B&D Roll-A-Pro User guide

1.0 USER OPERATING CONTROLS
PowerDrive &
Roll-A-Pro
Rolling Door Openers
Quick Operation Guide
02
05
Button Function
01 Open / Stop / Close
02 Flashes when a code is being stored
or when a remote control button is
pressed.
03 Flashes as the door closes and
remains on when closed.
04 Flashes as the door opens and
remains on when opened.
05 Indicates when the opener requires
service.
06 Is used for storing or erasing remote
control buttons for door operation.
01
03
04
06

TO DISENGAGE THE OPENER
2.0 MANUAL DOOR OPERATION
CAUTION: When the opener is manually
disengaged, the door is no longer locked.
To lock the door manually, re-engage the
opener after the door is closed.
TO ENGAGE THE OPENER
WARNING! Please test the manual release
mechanism to ensure that the manual
release is easy to operate. No more than
20kg of force should be required to
disengage the door using the manual
release cord. IF excessive force is required,
contact your dealer.
It is recommended to disengage the door with
the door in the closed position.
tip
Pull handle,
until you
hear a click Manually
operate door
Press to test
Pull handle,
until you
hear a click

Light StatusBattery
Solid OK
Flashing Replace
No light Replace
3.0 CODING A REMOTE CONTROL
STEP ONE
The opener can only be operated from remote
controllers that have been programmed into its
memory. Up to 64 remotes (8 for Roll-A-Pro) can be
programmed.
Battery Type: 1 x CR2032.
WARNING!: The battery is hazardous and must
be kept out of reach of children.The battery can
cause severe of fatal injuries within 2 hours or
less if swallowed or placed inside any part of the
body. If you suspect the battery has be
swallowed or placed inside any part of the body,
SEEK IMMEDIATE medical attention.
STEP THREE
Switch power on
Press and
release
HOLD for 3 sec
HOLD for 3 sec
RELEASE
STEP FOUR
Press to test
tip
STEP ONE
4.0 CHANGING A BATTERY
Check Light
Status Table
STEP TWO
tip
Use screwdriver
to remove
scews and
open
STEP THREE
Use non-metallic
object to push
out.
remove
controls cover
STEP TWO
RELEASE
HOLD
CODING REMOTE FROM THE OPENER
STEP ONE STEP TWO
Take a pre-coded
remote and press the
button to duplicate
REMOTELY CODING A REMOTE CONTROL
Remotely coding works when you have a
pre-coded remote control and are in range of the
opener.
tip
Use a pen,
HOLD for 2 sec
the middle button
through the
coding hole
STEP THREE
Opener ashes & beeps
HOLD for 3 sec
HOLD for 3 sec
RELEASE
Take new
remote
RELEASE
STEP FIVE
Press to test
Opener stops ashing &
beeping

(Requires Smart Hub)
5.0 SMART PHONE CONTROL
BEFORE YOU START
Download the B&D App
to your smartphone
STEP TWO
Ensure limits are
set prior to connecting
to wi
STEP ONE
Open APP
and click START
!
WARNING!: This device allows for operation of
the door when not in line-of-sight of the door
and opener. The door may operate unexpectedly,
therefore do not allow anything to stay in or near
the path of the door.
Go to phone settings,
then WiFi and select
(B&D000000)
The home WiFi router
is within range of
opener
The Smart Phone Control works via your home’s WiFi network.
Initial set up involves linking your phone app and smart hub
to your home network.
Set up new
Smart Hub in app
STEP THREE
Smart Hub connect
appears, ensure WiFi
network =
(B&D000000)
Follow
instructions in the app
Connect the Smart
Hub to power.
Upon completion,
test the opener
through the
B&D App.

6.0 TROUBLESHOOTING
SymptomPossible cause Remedy
Replace the battery
Faulty remote control
Flat battery
Replace remote control
Replace battery
Re-engage the opener
LED has failed
The opener
does not
work from
the remote
The opener does not
have power
Plug a device of similar
voltage (e.g. a hairdryer)
into the power point and
check it is OK.
The battery in the
remote control is at
The remote button is
not programmed to
operate the door.
Code in the remote control
button
CODE SET LED is
ashing yet the
opener is not working.
Ensure the correct button
on the transmitter is being
pressed.
One remote
works but
the other/s
do not
The motor is
running but
the door
remains
stationary
The opener is
disengaged
The remote
range varies
or is
restricted
Variations are normal
depending on
conditions e.g.
temperature or
external interference
Make sure you can see the
door when you use the
remote control
The battery life is
exhausted
Check the battery status as
per section 4 of this guide
The opener
light does
not work.
Contact dealer to organise
LED to be changed.
The door
reverses for
no appar-
ent reason
If Safety beams are
installed they may be
partially obstructed
Ensure the beam path is not
obstructed. Check the
alignment of the beams
The door
stops of
moves very
slowly
Garage door in poor
condition e.g. springs
may be broken
Check the door’s operation
(Optional Battery
Back Up Accessory)
the batteries may
have little OR no
charge
Connect mains power and
leave the batteries to
charge.The batteries may
take 24 to 48 hours to reach
their maximum charge
capacity.

7.0 CARING FOR YOUR OPENER
Preventative servicing of your garage door and opener, is
important.Your garage door is made up of numerous moving
parts designed to lift and lower your door safely and
efciently.
Ongoing preventative servicing ensures that your door
continues to function within factory specications, greatly
reduces the risk of failure and repair bills down the track and
ensure you maintain your Warranty.
Refer to your Owners Opener Handbook for your service
schedule available HERE.
Refer to the installation manual for monthly
testing procedures in Section 11 to ensure
garage door is t for use available HERE.
tip
Online warranty details are available HERE.
8.0 NEED A SERVICE CALL?
If the opener needs a service please call the dealer who
installed the garage door opener (their contact details are
usually on a sticker on the back of your garage door).
For product assistance, general enquiry or
more information, please visit:
bnd.com.au
or call 13 62 63.