B&R PC 1200 User manual

Panel PC 1200 pan-
el mount device
User's manual
Version: 1.08 (November 2021)
Order no.: MAPPC1200-ENG
Translation of the original documentation

Publishing information
B&R Industrial Automation GmbH
B&R Strasse 1
5142 Eggelsberg
Austria
Telephone: [phone]
Fax: [phone]
[email protected]
Disclaimer
All information in this manual is current as of its creation. The contents of this manual are subject to change without
notice. B&R Industrial Automation GmbH assumes unlimited liability in particular for technical or editorial errors
in this manual only (i) in the event of gross negligence or (ii) for culpably inflicted personal injury. Beyond that,
liability is excluded to the extent permitted by law. Liability in cases in which the law stipulates mandatory unlimited
liability (such as product liability) remains unaffected. Liability for indirect damage, consequential damage, business
interruption, loss of profit or loss of information and data is excluded, in particular for damage that is directly or
indirectly attributable to the delivery, performance and use of this material.
B&R Industrial Automation GmbH notes that the software and hardware designations and brand names of the
respective companies used in this document are subject to general trademark, brand or patent protection.
Hardware and software from third-party suppliers referenced in this manual is subject exclusively to the respective
terms of use of these third-party providers. B&R Industrial Automation GmbH assumes no liability in this regard.
Any recommendations made by B&R Industrial Automation GmbH are not contractual content, but merely non-
binding information for which no liability is assumed. When using hardware and software from third-party suppliers,
the relevant manuals of these third-party suppliers must additionally be consulted and, in particular, the safety
guidelines and technical specifications contained therein must be observed. The compatibility of the products from
B&R Industrial Automation GmbH described in this manual with hardware and software from third-party suppliers
is not contractual content unless this has been separately agreed in individual cases; in this respect, warranty for
such compatibility is excluded in any case, and it is the sole responsibility of the customer to verify this compatibility
in advance.
1575240488693-1.08

Table of contents
1 Introduction................................................................................................................7
1.1 Manual history.................................................................................................................................................7
1.2 Information about this document.................................................................................................................... 7
1.2.1 Organization of notices..............................................................................................................................7
1.2.2 Guidelines.................................................................................................................................................. 7
2 General safety guidelines........................................................................................ 9
2.1 Intended use................................................................................................................................................... 9
2.2 Protection against electrostatic discharge...................................................................................................... 9
2.2.1 Packaging.................................................................................................................................................. 9
2.2.2 Regulations for proper ESD handling....................................................................................................... 9
2.3 Regulations and measures........................................................................................................................... 10
2.4 Transport and storage.................................................................................................................................. 10
2.5 Installation..................................................................................................................................................... 10
2.6 Operation.......................................................................................................................................................10
2.6.1 Protection against contact with electrical parts.......................................................................................10
2.6.2 Ambient conditions - Dust, moisture, aggressive gases......................................................................... 11
2.6.3 Programs, viruses and malicious programs............................................................................................11
2.7 Cybersecurity disclaimer for products...........................................................................................................11
3 System overview..................................................................................................... 12
3.1 General information.......................................................................................................................................12
3.2 Order data.....................................................................................................................................................13
3.3 Overview........................................................................................................................................................14
4 Technical data......................................................................................................... 15
4.1 System data.................................................................................................................................................. 15
4.1.1 Technical data - 7.0" variants................................................................................................................. 15
4.1.2 Technical data - 10.1" variants............................................................................................................... 17
4.1.3 Technical data - 12.1" variants............................................................................................................... 19
4.1.4 Technical data - 15.6" variants............................................................................................................... 21
4.2 Product information....................................................................................................................................... 23
4.2.1 Identification.............................................................................................................................................23
4.3 Mechanical properties................................................................................................................................... 24
4.3.1 Dimensions.............................................................................................................................................. 24
4.3.1.1 7.0" variants....................................................................................................................................... 24
4.3.1.2 10.1" variants..................................................................................................................................... 25
4.3.1.3 12.1" variants..................................................................................................................................... 26
4.3.1.4 15.6" variants..................................................................................................................................... 27
4.3.2 Spacing for air circulation........................................................................................................................28
4.3.3 Mounting orientations.............................................................................................................................. 29
4.3.3.1 Typical application..............................................................................................................................29
4.3.3.2 Worst-case application.......................................................................................................................29
4.4 Environmental properties.............................................................................................................................. 32
4.4.1 Temperature monitoring.......................................................................................................................... 32
4.4.2 Temperature sensor positions.................................................................................................................32
4.4.3 Temperature/Humidity diagrams............................................................................................................. 33
4.4.4 Derating the ambient temperature.......................................................................................................... 35
4.4.4.1 Calculation example A (worst-case application)................................................................................35
4.4.4.2 Calculation example B (worst-case application)................................................................................35
4.4.4.3 Calculation example C (worst-case application)................................................................................35
4.4.4.4 Calculation example D (worst-case application)................................................................................35
4.4.4.5 Information about the use cases....................................................................................................... 36
4.4.5 Vibration and shock.................................................................................................................................37
4.5 Electrical properties.......................................................................................................................................38
4.5.1 Block diagram..........................................................................................................................................38
4.6 Device interfaces and slots...........................................................................................................................39
Panel PC 1200 panel mount device User's manual V1.08 3

Table of contents
4.6.1 Device interface overview....................................................................................................................... 39
4.6.1.1 24 VDC power supply........................................................................................................................39
4.6.1.2 Grounding...........................................................................................................................................40
4.6.1.3 Ethernet interfaces.............................................................................................................................40
4.6.1.4 USB interfaces................................................................................................................................... 41
4.6.1.5 CFast slot........................................................................................................................................... 41
4.6.1.6 Power and reset buttons....................................................................................................................42
4.6.1.7 LED status indicators.........................................................................................................................42
4.6.1.8 Battery................................................................................................................................................ 43
4.6.1.9 Trusted Platform Module (TPM)........................................................................................................ 43
4.7 Individual components.................................................................................................................................. 44
4.7.1 CFast cards............................................................................................................................................. 44
5 Installation and wiring............................................................................................ 45
5.1 Basic information...........................................................................................................................................45
5.1.1 Requirements for the installation cutout..................................................................................................46
5.1.1.1 Installation cutout............................................................................................................................... 47
5.2 Installation for mounting with retaining clips.................................................................................................48
5.2.1 Installing with retaining clips................................................................................................................... 48
5.3 Installing with a VESA bracket..................................................................................................................... 50
5.4 Grounding concept - Functional ground....................................................................................................... 51
5.5 Securing the connecting cables....................................................................................................................52
6 Commissioning........................................................................................................53
6.1 Basic information...........................................................................................................................................53
6.2 Switching on the device for the first time..................................................................................................... 53
6.2.1 General information before switching on the device...............................................................................53
6.2.2 Switching on the device.......................................................................................................................... 53
6.3 Touch screen calibration............................................................................................................................... 54
6.4 Display brightness control.............................................................................................................................54
6.5 General instructions for the temperature test procedure..............................................................................55
6.5.1 Procedure................................................................................................................................................ 55
6.5.2 Evaluating temperatures in Windows operating systems....................................................................... 55
6.5.2.1 Evaluating with the ADI Control Center.............................................................................................55
6.5.2.2 Evaluation with BurnInTest from PassMark.......................................................................................55
6.5.3 Evaluating the measurement results.......................................................................................................55
7 Software................................................................................................................... 56
7.1 UEFI BIOS options....................................................................................................................................... 56
7.1.1 General information................................................................................................................................. 56
7.1.1.1 Adaptation for touch operation.......................................................................................................... 56
7.1.1.2 Overview of BIOS description............................................................................................................56
7.1.2 BIOS Setup and startup procedure.........................................................................................................58
7.1.2.1 Input options.......................................................................................................................................58
7.1.3 Boot menu............................................................................................................................................... 60
7.1.4 Boot manager.......................................................................................................................................... 61
7.1.5 Device manager...................................................................................................................................... 62
7.1.6 Setup utility.............................................................................................................................................. 63
7.1.6.1 Main....................................................................................................................................................64
7.1.6.2 Advanced............................................................................................................................................65
7.1.6.3 Security...............................................................................................................................................74
7.1.6.4 Power................................................................................................................................................. 75
7.1.6.5 Boot.................................................................................................................................................... 77
7.1.6.6 Exit......................................................................................................................................................80
7.2 Upgrade information......................................................................................................................................81
7.2.1 UEFI BIOS upgrade................................................................................................................................ 81
7.2.1.1 BIOS upgrade.................................................................................................................................... 81
4 Panel PC 1200 panel mount device User's manual V1.08

Table of contents
7.2.2 PC firmware upgrade.............................................................................................................................. 81
7.2.2.1 Procedure in Windows (ADI Control Center).....................................................................................81
7.2.2.2 Procedure in the EFI shell.................................................................................................................82
7.2.2.3 Automatic firmware upgrade..............................................................................................................83
7.3 Multi-touch drivers.........................................................................................................................................83
7.4 Operating systems........................................................................................................................................ 84
7.4.1 Windows 10 IoT Enterprise 2019 LTSC..................................................................................................84
7.4.1.1 General information............................................................................................................................84
7.4.1.2 Order data.......................................................................................................................................... 84
7.4.1.3 Overview.............................................................................................................................................84
7.4.1.4 Features............................................................................................................................................. 84
7.4.1.5 Installation.......................................................................................................................................... 85
7.4.1.6 Drivers................................................................................................................................................ 85
7.4.1.7 Activation............................................................................................................................................86
7.4.1.8 Supported display resolutions............................................................................................................86
7.4.2 B&R Linux 10 (GNU/Linux)..................................................................................................................... 87
7.4.2.1 General information............................................................................................................................87
7.4.2.2 Order data.......................................................................................................................................... 87
7.4.2.3 Overview.............................................................................................................................................87
7.4.2.4 Features............................................................................................................................................. 87
7.4.2.5 Installation.......................................................................................................................................... 87
7.4.2.6 Drivers................................................................................................................................................ 87
7.5 Automation Device Interface (ADI)............................................................................................................... 88
7.5.1 ADI driver.................................................................................................................................................88
7.5.1.1 Installation.......................................................................................................................................... 88
7.5.1.2 ADI Control Center............................................................................................................................ 88
7.5.2 ADI Development Kit...............................................................................................................................89
7.5.3 ADI .NET SDK.........................................................................................................................................90
7.6 Key Editor......................................................................................................................................................91
7.7 KCF Editor.....................................................................................................................................................92
7.8 HMI Service Center...................................................................................................................................... 93
7.8.1 General information................................................................................................................................. 93
7.8.2 Order data............................................................................................................................................... 93
8 Maintenance.............................................................................................................94
8.1 Replacing the CFast card............................................................................................................................. 94
8.1.1 After changing the CFast card................................................................................................................ 95
8.2 Changing the battery.................................................................................................................................... 96
8.3 Cleaning........................................................................................................................................................ 98
8.4 Pixel errors....................................................................................................................................................99
8.5 User tips for increasing the service life of the display..................................................................................99
8.5.1 Backlight.................................................................................................................................................. 99
8.5.1.1 Measures to maintain backlight service life.......................................................................................99
8.5.2 Image persistence................................................................................................................................... 99
8.5.2.1 What causes image persistence?......................................................................................................99
8.5.2.2 How can image persistence be reduced?......................................................................................... 99
8.6 Repairs/Complaints and replacement parts..................................................................................................99
9 Accessories........................................................................................................... 100
9.1 0TB6102 2-pin power supply connector.....................................................................................................100
9.1.1 Order data............................................................................................................................................. 100
9.1.2 Technical data....................................................................................................................................... 100
9.2 Replacement parts...................................................................................................................................... 101
9.2.1 5ACCRHMI.0018-000 - Technical data.................................................................................................101
10 International and national certifications...........................................................102
10.1 Directives and declarations.......................................................................................................................102
Panel PC 1200 panel mount device User's manual V1.08 5

Table of contents
10.1.1 CE marking..........................................................................................................................................102
10.1.2 EMC Directive......................................................................................................................................102
10.2 Certifications..............................................................................................................................................103
10.2.1 UL certification.....................................................................................................................................103
10.2.2 EAC......................................................................................................................................................103
10.2.3 KC........................................................................................................................................................ 103
10.2.4 RCM.....................................................................................................................................................103
11 Environmentally friendly disposal.....................................................................104
11.1 Separation of materials............................................................................................................................. 104
A.1 MTCX.......................................................................................................................................................... 105
A.2 Viewing angles............................................................................................................................................106
A.3 Projected capacitive touch (PCT)...............................................................................................................107
A.4 Surface resistance of the touchscreen (PCT)............................................................................................ 107
6 Panel PC 1200 panel mount device User's manual V1.08

Introduction
1 Introduction
Information:
B&R makes every effort to keep documents as current as possible. The most current versions can be
downloaded from the B&R website (www.br-automation.com).
1.1 Manual history
Version Date Changes
1.08 November 2021 Dokument aktualisiert.
•Updated ground connection requirements, see Grounding, Grounding concept - Functional ground and
Securing the connecting cables.
•"Changing the battery" on page 96 aktualisiert.
•"Ethernet interfaces" on page 40 aktualisiert.
•"UEFI BIOS options" on page 56 aktualisiert.
•"Derating the ambient temperature" on page 35 aktualisiert.
°"Mounting orientations" on page 29 aktualisiert.
1.05 April 2021 Updated document, editorial changes.
•Added "Installation cutout" on page 47 and updated "Requirements for the installation cutout" on page
46.
•Updated "Technical data - 10.1" variants" on page 17 and "Technical data - 15.6" variants" on page
21.
•Updated "Derating the ambient temperature" on page 35.
°Updated "Mounting orientations" on page 29.
1.00 December 2020 First official version
1.2 Information about this document
This document is not intended for end customers! The safety guidelines required for end customers
must be incorporated into the operating instructions for end customers in the respective national lan-
guage by the machine manufacturer or system provider.
1.2.1 Organization of notices
Safety notices
Contain only information that warns of dangerous functions or situations.
Signal word Description
Danger! Failure to observe these safety guidelines and notices will result in death, severe injury or substantial damage to property.
Warning! Failure to observe these safety guidelines and notices can result in death, severe injury or substantial damage to property.
Caution! Failure to observe these safety guidelines and notices can result in minor injury or damage to property.
Notice! Failure to observe these safety guidelines and notices can result in damage to property.
General notices
Contain useful information for users and instructions for avoiding malfunctions.
Signal word Description
Information: Useful information, application tips and instructions for avoiding malfunctions.
1.2.2 Guidelines
European dimension standards apply to all dimension diagrams.
All dimensions in millimeters.
Unless otherwise specified, the following general tolerances apply:
Panel PC 1200 panel mount device User's manual V1.08 7

Introduction
Nominal dimension range General tolerance per
DIN ISO 2768 medium
Up to 6 mm ±0.1 mm
Over 6 to 30 mm ±0.2 mm
Over 30 to 120 mm ±0.3 mm
Over 120 to 400 mm ±0.5 mm
Over 400 to 1000 mm ±0.8 mm
8 Panel PC 1200 panel mount device User's manual V1.08

General safety guidelines
2 General safety guidelines
2.1 Intended use
In all cases, it is necessary to observe and comply with applicable national and international standards, regulations
and safety measures!
The B&R products described in this manual are intended for use in industry and industrial applications.
The intended use includes control, operation, monitoring, drive and HMI tasks as part of automation processes
in machines and systems.
B&R products are only permitted to be used in their original condition. Modifications and extensions are only per-
mitted if they are described in this manual.
B&R excludes liability for damage of any kind resulting from the use of B&R products in any intended way.
B&R products have not been designed, developed and manufactured for use that involves fatal risks or hazards
that could result in death, injury, serious physical harm or other loss without the assurance of exceptionally stringent
safety precautions.
B&R products are explicitly not intended for use in the following applications:
•Monitoring and control of thermonuclear processes
•Weapon systems control
•Flight and traffic control systems for passenger and freight transport
•Health monitoring and life support systems
2.2 Protection against electrostatic discharge
Electrical assemblies that can be damaged by electrostatic discharge (ESD) must be handled accordingly.
2.2.1 Packaging
•Electrical assemblies with housing:
Do not require special ESD packaging but must be handled properly (see "Electrical assemblies with hous-
ing").
•Electrical assemblies without housing:
Are protected by ESD-suitable packaging.
2.2.2 Regulations for proper ESD handling
Electrical assemblies with housing
•Do not touch the connector contacts of connected cables.
•Do not touch the contact tips on circuit boards.
Electrical assemblies without housing
The following applies in addition to "Electrical assemblies with housing":
•All persons handling electrical assemblies and devices in which electrical assemblies are installed must
be grounded.
•Assemblies are only permitted to be touched on the narrow sides or front plate.
•Always place assemblies on suitable surfaces (ESD packaging, conductive foam, etc.). Metallic surfaces
are not suitable surfaces!
•Assemblies must not be subjected to electrostatic discharges (e.g. due to charged plastics).
Panel PC 1200 panel mount device User's manual V1.08 9

General safety guidelines
•A minimum distance of 10 cm from monitors or television sets must be maintained.
•Measuring instruments and devices must be grounded.
•Test probes of floating potential measuring instruments must be discharged briefly on suitable grounded
surfaces before measurement.
Individual components
•ESD protective measures for individual components are implemented throughout B&R (conductive floors,
shoes, wrist straps, etc.).
•The increased ESD protective measures for individual components are not required for handling B&R
products at customer locations.
2.3 Regulations and measures
Electronic devices are generally not failsafe. If the programmable logic controller, operating or control device or
uninterruptible power supply fails, the user is responsible for ensuring that connected devices (such as motors)
are brought to a safe state.
When using programmable logic controllers as well as when using operating and monitoring devices as control
systems in conjunction with a Soft PLC (e.g. B&R Automation Runtime or similar product) or Slot PLC (e.g. B&R
LS251 or similar product), the safety measures that apply to industrial controllers (protection by protective equip-
ment such as emergency stops) must be observed in accordance with applicable national and international regu-
lations. This also applies to all other connected devices, such as drives.
All work such as installation, commissioning and servicing are only permitted to be carried out by qualified person-
nel. Qualified personnel are persons who are familiar with the transport, installation, assembly, commissioning and
operation of the product and have the appropriate qualifications for their job (e.g. IEC 60364). National accident
prevention regulations must be observed.
The safety guidelines, information about connection conditions (nameplate and documentation) and limit values
specified in the technical data must be read carefully before installation and commissioning and must be strictly
observed.
2.4 Transport and storage
During transport and storage, devices must be protected against undue stress (mechanical stress, temperature,
humidity, aggressive atmosphere).
2.5 Installation
•The devices are not ready for use and must be installed and wired according to the requirements of this
documentation in order to comply with EMC limit values.
•Installation must be carried out according to the documentation using suitable equipment and tools.
•Devices are only permitted to be installed in a voltage-free state and by qualified personnel. The control
cabinet must first be disconnected from the power supply and secured against being switched on again.
•General safety regulations and national accident prevention regulations must be observed.
•The electrical installation must be carried out in accordance with relevant regulations (e.g. line cross section,
fuse protection, protective ground connection).
2.6 Operation
2.6.1 Protection against contact with electrical parts
In order to operate programmable logic controllers, operating and monitoring devices and uninterruptible power
supplies, it is necessary for certain components to carry dangerous voltages over 42 VDC. Touching one of these
components can result in a life-threatening electric shock. There is a risk of death, serious injury or damage to
property.
Before switching on programmable logic controllers, operating and monitoring devices and uninterruptible power
supplies, it must be ensured that the housing is properly connected to ground potential (PE rail). Ground connec-
tions must also be made if the operating and monitoring device and uninterruptible power supply are only connect-
ed for testing purposes or only operated for a short time!
Before switching on, live parts must be securely covered. All covers must be kept closed during operation.
10 Panel PC 1200 panel mount device User's manual V1.08

General safety guidelines
2.6.2 Ambient conditions - Dust, moisture, aggressive gases
The use of operating and monitoring devices (e.g. industrial PCs, Power Panels, Mobile Panels) and uninterruptible
power supplies in dusty environments must be avoided. This can otherwise result in dust deposits that affect the
functionality of the device, especially in systems with active cooling (fans), which may no longer ensure sufficient
cooling.
The presence of aggressive gases in the environment can also result in malfunctions. In combination with high
temperature and relative humidity, aggressive gases – for example with sulfur, nitrogen and chlorine components
– trigger chemical processes that can very quickly impair or damage electronic components. Blackened copper
surfaces and cable ends in existing installations are indicators of aggressive gases.
When operated in rooms with dust and condensation that can endanger functionality, operating and monitoring
devices such as Automation Panels or Power Panels are protected on the front against the ingress of dust and
moisture when installed correctly (e.g. cutout installation). The back of all devices must be protected against the
ingress of dust and moisture, however, or the dust deposits must be removed at suitable intervals.
2.6.3 Programs, viruses and malicious programs
Any data exchange or installation of software using data storage media (e.g. floppy disk, CD-ROM, USB flash
drive) or via networks or the Internet poses a potential threat to the system. It is the direct responsibility of the user
to avert these dangers and to take appropriate measures such as virus protection programs and firewalls to protect
against them and to use only software from trustworthy sources.
2.7 Cybersecurity disclaimer for products
B&R products communicate via a network interface and were developed for secure connection with internal and,
if necessary, other networks such as the Internet.
Information:
In the following, B&R products are referred to as "product" and all types of networks (e.g. internal
networks and the Internet) are referred to as "network".
It is the sole responsibility of the customer to establish and continuously ensure a secure connection between
the product and the network. In addition, appropriate security measures must be implemented and maintained
to protect the product and entire network from any security breaches, unauthorized access, interference, digital
intrusion, data leakage and/or theft of data or information.
B&R Industrial Automation GmbH and its subsidiaries are not liable for damages and/or losses in connection
with security breaches, unauthorized access, interference, digital intrusion, data leakage and/or theft of data or
information.
The aforementioned appropriate security measures include, for example:
•Segmentation of the network (e.g. separation of the IT network from the control network1))
•Use of firewalls
•Use of authentication mechanisms
•Encryption of data
•Use of anti-malware software
Before B&R releases products or updates, they are subjected to appropriate functional testing. Independently of
this, we recommend that our customers develop their own test processes in order to be able to check the effects
of changes in advance. Such changes include, for example:
•Installation of product updates
•Significant system modifications such as configuration changes
•Deployment of updates or patches for third-party software (non-B&R software)
•Hardware replacement
These tests should ensure that implemented security measures remain effective and that systems in the customer's
environment behave as expected.
1) The term "control network" refers to computer networks used to connect control systems. The control network can be divided into zones, and there can be
several separate control networks within a company or site. The term "control systems" refers to all types of B&R products such as controllers (e.g. X20), HMI
systems (e.g. Power Panel T30), process control systems (e.g. APROL) and supporting systems such as engineering workstations with Automation Studio.
Panel PC 1200 panel mount device User's manual V1.08 11

System overview
3 System overview
3.1 General information
With the Panel PC 1200, B&R offers an all-in-one PC family as part of the product portfolio. Its compact design
allows installation in almost any control cabinet. By using removable mass storage devices that can be expanded
up to 256 GB, the Panel PC 1200 is ideal for installing Windows or Linux operating systems. Four different display
diagonals with projected capacitive multi-touch screens make the Panel PC 1200 an optimal solution for a variety
of applications – even in harsh industrial environments.
•Compact and robust design
•Powerful with Intel Atom x5-E3940 1.6 GHz quad-core processor and 4 GB LPDDR4 RAM
•Widescreen variants from 7.0" to 15.6" with PCT multi-touch
•Installation dimensions compatible with Automation Panel 1000
•Installing with retaining clips or with VESA bracket
•Low installation depth
•Low maintenance with fanless operation
•2x USB 3.0
•2x Gigabit Ethernet
•1x CFast slot
•Real time clock, RTC (battery-backed)
•TPM 2.0 security
•5PPC1200.xxxx-xxA: Anti-glare display
•5PPC1200.xxxx-xxB: Clear glass display
12 Panel PC 1200 panel mount device User's manual V1.08

System overview
3.2 Order data
Order number Short description Figure
Display variants
5PPC1200.0702-10A Panel PC 1200, 7", glass front. CPU and memory: Intel Atom
E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM. Display and
touch screen: 7", 800 x 480 pixels (WVGA) widescreen, mul-
ti-touch (projected capacitive), control cabinet installation, land-
scape format, anti-glare. Interfaces: 2x Ethernet 10/100/1000
Mbit/s, 2x USB 3.0.
5PPC1200.0702-10B Panel PC 1200, 7", glass front. CPU and memory: Intel Atom
E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM. Display and
touch screen: 7", 800 x 480 pixels (WVGA) widescreen, mul-
ti-touch (projected capacitive), control cabinet installation, land-
scape format, clear glass. Interfaces: 2x Ethernet 10/100/1000
Mbit/s, 2x USB 3.0.
5PPC1200.101E-10A Panel PC 1200, 10.1", glass front. CPU and memory: Intel
Atom E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM. Dis-
play and touch screen: 10.1", 1280 x 800 pixels (WXGA)
widescreen, multi-touch (projected capacitive), control cabinet
installation, landscape format, anti-glare. Interfaces: 2x Ethernet
10/100/1000 Mbit/s, 2x USB 3.0.
5PPC1200.101E-10B Panel PC 1200, 10.1", glass front. CPU and memory: Intel
Atom E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM. Dis-
play and touch screen: 10.1", 1280 x 800 pixels (WXGA)
widescreen, multi-touch (projected capacitive), control cabinet
installation, landscape format, clear glass. Interfaces: 2x Ether-
net 10/100/1000 Mbit/s, 2x USB 3.0.
5PPC1200.121E-10A Panel PC 1200, 12.1", glass front. CPU and memory: Intel
Atom E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM. Dis-
play and touch screen: 12.1", 1280 x 800 pixels (WXGA)
widescreen, multi-touch (projected capacitive), control cabinet
installation, landscape format, anti-glare. Interfaces: 2x Ethernet
10/100/1000 Mbit/s, 2x USB 3.0.
5PPC1200.121E-10B Panel PC 1200, 12.1", glass front. CPU and memory: Intel
Atom E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM. Dis-
play and touch screen: 12.1", 1280 x 800 pixels (WXGA)
widescreen, multi-touch (projected capacitive), control cabinet
installation, landscape format, clear glass. Interfaces: 2x Ether-
net 10/100/1000 Mbit/s, 2x USB 3.0.
5PPC1200.156B-10A Panel PC 1200, 15.6", glass front. CPU and memory: Intel Atom
E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM. Display and
touch screen: 15.6", 1366 x 768 pixels (HD) widescreen, mul-
ti-touch (projected capacitive), control cabinet installation, land-
scape format, anti-glare. Interfaces: 2x Ethernet 10/100/1000
Mbit/s, 2x USB 3.0.
5PPC1200.156B-10B Panel PC 1200, 15.6", glass front. CPU and memory: Intel Atom
E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM. Display and
touch screen: 15.6", 1366 x 768 pixels (HD) widescreen, mul-
ti-touch (projected capacitive), control cabinet installation, land-
scape format, clear glass. Interfaces: 2x Ethernet 10/100/1000
Mbit/s, 2x USB 3.0.
Optional accessories
Accessories
5ACCRRPC1.0000-000 Montagesatz für Varianten des PPC1200: 9x Halteklammer mit
Drehmomentbegrenzung, 1x 2-polige Federzugklemme, 1x 2-
polige Schraubklemme
CFast cards
5CFAST.032G-10 CFast 32 GB MLC
5CFAST.064G-10 CFast 64 GB MLC
5CFAST.128G-10 CFast 128 GB MLC
5CFAST.256G-10 CFast 256 GB MLC
Terminal blocks
0TB6102.3000-00 2-pin accessory screw clamp terminal block (3.81)
0TB6102.3100-00 Accessory 2-pin cage clamp terminal block (3.81)
Panel PC 1200 panel mount device User's manual V1.08 13

System overview
3.3 Overview
Order number Short description Page
Accessories
5ACCRHMI.0018-000 HMI C80/PPC1200 battery compartment - 1x battery holder C80/PPC1200 - 1x battery including circuit board 101
5SWUTI.0001-000 HMI Service Center USB flash drive - Hardware diagnostic software - For APC910/PPC900 - For PPC1200 -
For APC2100/PPC2100 - For APC2200/PPC2200 - For APC3100/PPC3100 - For APC mobile - For AP800/
AP900 - For AP9x3/AP9xD - For AP1000/AP5000
93
B&R Linux 10
5SWLIN.0865-MUL B&R Linux 10 - 64-bit - Multilingual - PPC1200 (UEFI boot) - Installation - Only available with a new device 87
Display variants
5PPC1200.0702-10A Panel PC 1200, 7", glass front. CPU and memory: Intel Atom E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM.
Display and touch screen: 7", 800 x 480 pixels (WVGA) widescreen, multi-touch (projected capacitive), control
cabinet installation, landscape format, anti-glare. Interfaces: 2x Ethernet 10/100/1000 Mbit/s, 2x USB 3.0.
13
5PPC1200.0702-10B Panel PC 1200, 7", glass front. CPU and memory: Intel Atom E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM.
Display and touch screen: 7", 800 x 480 pixels (WVGA) widescreen, multi-touch (projected capacitive), control
cabinet installation, landscape format, clear glass. Interfaces: 2x Ethernet 10/100/1000 Mbit/s, 2x USB 3.0.
13
5PPC1200.101E-10A Panel PC 1200, 10.1", glass front. CPU and memory: Intel Atom E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM.
Display and touch screen: 10.1", 1280 x 800 pixels (WXGA) widescreen, multi-touch (projected capacitive),
control cabinet installation, landscape format, anti-glare. Interfaces: 2x Ethernet 10/100/1000 Mbit/s, 2x USB
3.0.
13
5PPC1200.101E-10B Panel PC 1200, 10.1", glass front. CPU and memory: Intel Atom E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM.
Display and touch screen: 10.1", 1280 x 800 pixels (WXGA) widescreen, multi-touch (projected capacitive),
control cabinet installation, landscape format, clear glass. Interfaces: 2x Ethernet 10/100/1000 Mbit/s, 2x USB
3.0.
13
5PPC1200.121E-10A Panel PC 1200, 12.1", glass front. CPU and memory: Intel Atom E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM.
Display and touch screen: 12.1", 1280 x 800 pixels (WXGA) widescreen, multi-touch (projected capacitive),
control cabinet installation, landscape format, anti-glare. Interfaces: 2x Ethernet 10/100/1000 Mbit/s, 2x USB
3.0.
13
5PPC1200.121E-10B Panel PC 1200, 12.1", glass front. CPU and memory: Intel Atom E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM.
Display and touch screen: 12.1", 1280 x 800 pixels (WXGA) widescreen, multi-touch (projected capacitive),
control cabinet installation, landscape format, clear glass. Interfaces: 2x Ethernet 10/100/1000 Mbit/s, 2x USB
3.0.
13
5PPC1200.156B-10A Panel PC 1200, 15.6", glass front. CPU and memory: Intel Atom E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM.
Display and touch screen: 15.6", 1366 x 768 pixels (HD) widescreen, multi-touch (projected capacitive), control
cabinet installation, landscape format, anti-glare. Interfaces: 2x Ethernet 10/100/1000 Mbit/s, 2x USB 3.0.
13
5PPC1200.156B-10B Panel PC 1200, 15.6", glass front. CPU and memory: Intel Atom E3940 1.6 GHz, quad core, 4 GB LPDDR4 RAM.
Display and touch screen: 15.6", 1366 x 768 pixels (HD) widescreen, multi-touch (projected capacitive), control
cabinet installation, landscape format, clear glass. Interfaces: 2x Ethernet 10/100/1000 Mbit/s, 2x USB 3.0.
13
Terminal blocks
0TB6102.3000-00 2-pin accessory screw clamp terminal block (3.81) 100
0TB6102.3100-00 Accessory 2-pin cage clamp terminal block (3.81) 100
Windows 10 IoT Enterprise 2019 LTSC
5SWW10.0965-MUL Windows 10 IoT Enterprise 2019 LTSC - 64-bit - Entry - Multilingual - PPC1200 (UEFI boot) - License - Only
available with a new device
84
14 Panel PC 1200 panel mount device User's manual V1.08

Technical data
4 Technical data
4.1 System data
4.1.1 Technical data - 7.0" variants
Information:
The following specified characteristic data, features and limit values are only valid for these individual
components and may differ from those of the complete system. The data specified for the complete
system applies to the complete system in which this individual component is used, for example.
Order number 5PPC1200.0702-10A 5PPC1200.0702-10B
General information
LEDs Power, Disk
B&R ID code 0xA69C 0xA6BB
Cooling Passive
Power button Yes
Reset button Yes
Type All-in-one PC
Certifications
CE Yes
UL In preparation
Controller
Bootloader UEFI BIOS
Processor
Type Intel Atom x5-E3940
Clock frequency 1600 MHz
Number of cores 4
Architecture 14 nm
Thermal design power (TDP) 9.5 W
L2 cache 2 MB
Intel 64 architecture Yes
Intel Hyper-Threading Technology No
Intel vPro Technology No
Intel Virtualization Technology (VT-x) Yes
Intel Virtualization Technology for Directed I/O
(VT-d)
Yes
Enhanced Intel SpeedStep Technology Yes
Chipset Apollo Lake
Trusted Platform Module TPM 2.0
Real-time clock
Accuracy At 25 °C: Typ. 12 ppm (1 second) per day 1)
Self-discharge time Approx. 8 years
Battery-backed Yes
Memory
Type LPDDR4 SDRAM
Memory size 4 GB
Velocity DDR4L-2133
Memory interface width Dual channel
Removable No
Graphics
Controller Intel HD Graphics
Max. dynamic graphics frequency 600 MHz
Color depth Max. 32-bit
DirectX support 12
OpenGL support 4.3
Power management ACPI 5.0
Display
Type TFT color
Diagonal 7.0"
Colors 16.7 million
Resolution WVGA, 800 x 480 px
Contrast Typ. 800:1
Viewing angles
Horizontal Direction L / Direction R = Typ. 89°, min. 80°
Vertical Direction U / Direction D = Typ. 89°, min. 80°
Panel PC 1200 panel mount device User's manual V1.08 15

Technical data
Order number 5PPC1200.0702-10A 5PPC1200.0702-10B
Backlight
Type LED
Brightness (dimmable) Typ. 25 to 500 cd/m²
Half-brightness time 50,000 h
Filter glass
Transmittance ≥85%
Anti-glare coating Optical/Gloss = 70 No
Touch screen
Type Multi-touch
Technology PCT (projected capacitive touch)
Interfaces
CFast slot
Quantity 1
Type SATA III (SATA 6.0 Gbit/s)
USB
Quantity 2
Type USB 3.0
Variant Type A
Transfer rate Low speed (1.5 Mbit/s), full speed (12 Mbit/s), high speed (480 Mbit/s) to SuperSpeed (5 Gbit/s) 2)
Current-carrying capacity Max. 1 A per connection
Ethernet
Quantity 2
Variant RJ45, shielded
Transfer rate 10/100/1000 Mbit/s
Electrical properties
Nominal voltage 24 VDC ±25%, SELV/PELV 3)
Nominal current Max. 1.5 A
Inrush current Typ. 5 A, max. 100 A for < 50 μs
Power consumption 4) 36 W
Overvoltage category per EN 61131-2 II
Galvanic isolation No
Operating conditions
Pollution degree per EN 61131-2 Pollution degree 2
Degree of protection per EN 60529 Back: IP20
Front: IP55
Ambient conditions
Temperature
Operation -20 to 60°C 5)
Storage -20 to 80 °C
Transport -20 to 80 °C
Relative humidity See section "Temperature/Humidity diagrams".
Elevation
Operation Max. 3000 m 5)
Mechanical properties
Front
Design Black
Dimensions
Width 209 mm
Height 153 mm
Depth 41.5 mm
Weight Approx. 1130 g
1) At max. specified ambient temperature: Typ. 58 ppm (5 seconds) - worst case 220 ppm (19 seconds).
2) The SuperSpeed transfer rate (5 Gbit/s) is only possible with USB 3.0.
3) IEC 61010-2-201 requirements must be observed.
4) Power consumption including all interfaces.
5) The temperature specifications correspond to a specification at 500 meters above sea level. The max. ambient temperature is typically derated 1 °C per
1000 meters starting at 500 m above sea level.
16 Panel PC 1200 panel mount device User's manual V1.08

Technical data
4.1.2 Technical data - 10.1" variants
Information:
The following specified characteristic data, features and limit values are only valid for these individual
components and may differ from those of the complete system. The data specified for the complete
system applies to the complete system in which this individual component is used, for example.
Order number 5PPC1200.101E-10A 5PPC1200.101E-10B
General information
LEDs Power, Disk
B&R ID code 0xA6EE 0xA6EF
Cooling Passive
Power button Yes
Reset button Yes
Type All-in-one PC
Certifications
CE Yes
UL In preparation
Controller
Bootloader UEFI BIOS
Processor
Type Intel Atom x5-E3940
Clock frequency 1600 MHz
Number of cores 4
Architecture 14 nm
Thermal design power (TDP) 9.5 W
L2 cache 2 MB
Intel 64 architecture Yes
Intel Hyper-Threading Technology No
Intel vPro Technology No
Intel Virtualization Technology (VT-x) Yes
Intel Virtualization Technology for Directed I/O
(VT-d)
Yes
Enhanced Intel SpeedStep Technology Yes
Chipset Apollo Lake
Trusted Platform Module TPM 2.0
Real-time clock
Accuracy At 25 °C: Typ. 12 ppm (1 second) per day 1)
Self-discharge time Approx. 8 years
Battery-backed Yes
Memory
Type LPDDR4 SDRAM
Memory size 4 GB
Velocity DDR4L-2133
Memory interface width Dual channel
Removable No
Graphics
Controller Intel HD Graphics
Max. dynamic graphics frequency 600 MHz
Color depth Max. 32-bit
DirectX support 12
OpenGL support 4.3
Power management ACPI 5.0
Display
Type TFT color
Diagonal 10.1"
Colors 16.7 million
Resolution WXGA, 1280 x 800 px
Contrast Typ. 800:1
Viewing angles
Horizontal Direction L / Direction R = Typ. 85°
Vertical Direction U / Direction D = Typ. 85°
Backlight
Type LED
Brightness (dimmable) Typ. 25 to 500 cd/m²
Half-brightness time 50,000 h
Filter glass
Transmittance ≥85%
Anti-glare coating Optical/Gloss = 70 No
Touch screen
Type Multi-touch
Technology PCT (projected capacitive touch)
Panel PC 1200 panel mount device User's manual V1.08 17

Technical data
Order number 5PPC1200.101E-10A 5PPC1200.101E-10B
Interfaces
CFast slot
Quantity 1
Type SATA III (SATA 6.0 Gbit/s)
USB
Quantity 2
Type USB 3.0
Variant Type A
Transfer rate Low speed (1.5 Mbit/s), full speed (12 Mbit/s), high speed (480 Mbit/s) to SuperSpeed (5 Gbit/s) 2)
Current-carrying capacity Max. 1 A per connection
Ethernet
Quantity 2
Variant RJ45, shielded
Transfer rate 10/100/1000 Mbit/s
Electrical properties
Nominal voltage 24 VDC ±25%, SELV/PELV 3)
Nominal current Max. 1.6 A
Inrush current Typ. 5 A, max. 100 A for < 50 μs
Power consumption 4) 38.4 W
Overvoltage category per EN 61131-2 II
Galvanic isolation No
Operating conditions
Pollution degree per EN 61131-2 Pollution degree 2
Degree of protection per EN 60529 Back: IP20
Front: IP55
Ambient conditions
Temperature
Operation Rev. B2 and later: -20 to 60°C
Up to Rev. B1: -20 to 55°C 5)
Storage -20 to 80 °C
Transport -20 to 80 °C
Relative humidity See section "Temperature/Humidity diagrams".
Elevation
Operation Max. 3000 m 5)
Mechanical properties
Front
Design Black
Dimensions
Width 279 mm
Height 191 mm
Depth 41.2 mm
Weight Approx. 1680 g
1) At max. specified ambient temperature: Typ. 58 ppm (5 seconds) - worst case 220 ppm (19 seconds).
2) The SuperSpeed transfer rate (5 Gbit/s) is only possible with USB 3.0.
3) IEC 61010-2-201 requirements must be observed.
4) Power consumption including all interfaces.
5) The temperature specifications correspond to a specification at 500 meters above sea level. The max. ambient temperature is typically derated 1 °C per
1000 meters starting at 500 m above sea level.
18 Panel PC 1200 panel mount device User's manual V1.08

Technical data
4.1.3 Technical data - 12.1" variants
Information:
The following specified characteristic data, features and limit values are only valid for these individual
components and may differ from those of the complete system. The data specified for the complete
system applies to the complete system in which this individual component is used, for example.
Order number 5PPC1200.121E-10A 5PPC1200.121E-10B
General information
LEDs Power, Disk
B&R ID code 0xA6F0 0xA6F1
Cooling Passive
Power button Yes
Reset button Yes
Type All-in-one PC
Certifications
CE Yes
UL In preparation
Controller
Bootloader UEFI BIOS
Processor
Type Intel Atom x5-E3940
Clock frequency 1600 MHz
Number of cores 4
Architecture 14 nm
Thermal design power (TDP) 9.5 W
L2 cache 2 MB
Intel 64 architecture Yes
Intel Hyper-Threading Technology No
Intel vPro Technology No
Intel Virtualization Technology (VT-x) Yes
Intel Virtualization Technology for Directed I/O
(VT-d)
Yes
Enhanced Intel SpeedStep Technology Yes
Chipset Apollo Lake
Trusted Platform Module TPM 2.0
Real-time clock
Accuracy At 25°C: Typ. 12 ppm (1 second) per day 1)
Self-discharge time Approx. 8 years
Battery-backed Yes
Memory
Type LPDDR4 SDRAM
Memory size 4 GB
Velocity DDR4L-2133
Memory interface width Dual channel
Removable No
Graphics
Controller Intel HD Graphics
Max. dynamic graphics frequency 600 MHz
Color depth Max. 32-bit
DirectX support 12
OpenGL support 4.3
Power management ACPI 5.0
Display
Type TFT color
Diagonal 12.1"
Colors 16.7 million
Resolution WXGA, 1280 x 800 px
Contrast Typ. 800:1
Viewing angles
Horizontal Direction L / Direction R = Typ. 80°
Vertical Direction U = Typ. 80° / Direction D = Typ. 65°
Backlight
Type LED
Brightness (dimmable) Typ. 40 to 400 cd/m²
Half-brightness time 50,000 h
Filter glass
Transmittance ≥85%
Anti-glare coating Optical/Gloss = 70 No
Touch screen
Type Multi-touch
Technology PCT (projected capacitive touch)
Panel PC 1200 panel mount device User's manual V1.08 19

Technical data
Order number 5PPC1200.121E-10A 5PPC1200.121E-10B
Interfaces
CFast slot
Quantity 1
Type SATA III (SATA 6.0 Gbit/s)
USB
Quantity 2
Type USB 3.0
Variant Type A
Transfer rate Low speed (1.5 Mbit/s), full speed (12 Mbit/s), high speed (480 Mbit/s) to SuperSpeed (5 Gbit/s) 2)
Current-carrying capacity Max. 1 A per connection
Ethernet
Quantity 2
Variant RJ45, shielded
Transfer rate 10/100/1000 Mbit/s
Electrical properties
Nominal voltage 24 VDC ±25%, SELV/PELV 3)
Nominal current Max. 2.2 A
Inrush current Typ. 5 A, max. 100 A for < 50 μs
Power consumption 4) 52.8 W
Overvoltage category per EN 61131-2 II
Galvanic isolation No
Operating conditions
Pollution degree per EN 61131-2 Pollution degree 2
Degree of protection per EN 60529 Back: IP20
Front: IP55
Ambient conditions
Temperature
Operation -20 to 60°C 5)
Storage -20 to 80°C
Transport -20 to 80°C
Relative humidity See section "Temperature/Humidity diagrams".
Elevation
Operation Max. 3000 m 5)
Mechanical properties
Front
Design Black
Dimensions
Width 324 mm
Height 221.5 mm
Depth 43.2 mm
Weight Approx. 2230 g
1) At max. specified ambient temperature: Typ. 58 ppm (5 seconds) - worst case 220 ppm (19 seconds).
2) The SuperSpeed transfer rate (5 Gbit/s) is only possible with USB 3.0.
3) IEC 61010-2-201 requirements must be observed.
4) Power consumption including all interfaces.
5) The temperature specifications correspond to a specification at 500 meters above sea level. The max. ambient temperature is typically derated 1°C per 1000
meters starting at 500 m above sea level.
20 Panel PC 1200 panel mount device User's manual V1.08