B&R Automation Panel 5000 User manual

Automation Panel 5000
User's manual
Version: 2.11 (July 2020)
Order no.: MAAP5000-ENG
Translation of the original documentation
All values in this manual are current as of its creation. We reserve the right to change the contents of this manual
without notice. B&R Industrial Automation GmbH is not liable for technical or editorial errors and defects in this
manual. In addition, B&R Industrial Automation GmbH assumes no liability for damages that are directly or indirectly
attributable to the delivery, performance or use of this material. We point out that the software and hardware
designations and brand names of the respective companies used in this document are subject to general trademark,
brand or patent protection.

Table of contents
2 Automation Panel 5000 User's manual V2.11
1 Introduction................................................................................................................8
1.1 Manual history.................................................................................................................................................8
1.2 Information about this document.................................................................................................................. 11
1.2.1 Organization of safety notices.................................................................................................................11
1.2.2 Guidelines................................................................................................................................................ 11
2 General safety guidelines...................................................................................... 12
2.1 Intended use................................................................................................................................................. 12
2.2 Protection against electrostatic discharge.................................................................................................... 12
2.2.1 Packaging................................................................................................................................................ 12
2.2.2 Regulations for proper ESD handling..................................................................................................... 12
2.3 Regulations and measures........................................................................................................................... 12
2.4 Transport and storage.................................................................................................................................. 13
2.5 Installation..................................................................................................................................................... 13
2.6 Operation.......................................................................................................................................................13
2.6.1 Protection against contact with electrical parts.......................................................................................13
2.6.2 Ambient conditions - Dust, moisture, aggressive gases......................................................................... 13
2.6.3 Programs, viruses and malicious programs............................................................................................14
2.7 Cybersecurity disclaimer for products...........................................................................................................14
3 System overview..................................................................................................... 15
3.1 Information about this user's manual............................................................................................................15
3.2 Easy customization....................................................................................................................................... 15
3.3 Description of individual modules................................................................................................................. 16
3.3.1 AP5000 panels........................................................................................................................................ 16
3.3.2 Link modules........................................................................................................................................... 16
3.3.3 Mounting units......................................................................................................................................... 16
3.3.4 Flanges.................................................................................................................................................... 17
3.3.5 Expansion units....................................................................................................................................... 17
3.3.6 Handles....................................................................................................................................................17
3.4 Configuration................................................................................................................................................. 18
3.5 Overview........................................................................................................................................................19
4 Technical data......................................................................................................... 21
4.1 Complete system.......................................................................................................................................... 21
4.1.1 Connection options..................................................................................................................................21
4.1.1.1 SDL operation.................................................................................................................................... 21
4.1.1.2 DVI operation..................................................................................................................................... 23
4.1.1.3 SDL3 operation.................................................................................................................................. 25
4.1.1.4 SDL4 operation.................................................................................................................................. 26
4.1.2 Electrical properties................................................................................................................................. 28
4.1.2.1 Block diagrams...................................................................................................................................28
4.1.2.2 Power calculation...............................................................................................................................29
4.1.3 Mechanical properties..............................................................................................................................30
4.1.3.1 Dimensions.........................................................................................................................................30
4.1.3.2 Mounting orientations.........................................................................................................................39
4.1.3.3 Weight................................................................................................................................................ 40
4.1.4 Environmental properties.........................................................................................................................42
4.1.4.1 Temperature specifications................................................................................................................ 42
4.1.4.2 Relative humidity................................................................................................................................46
4.1.4.3 Vibration and shock........................................................................................................................... 46
4.1.4.4 Degree of protection.......................................................................................................................... 46
4.1.5 Device interfaces..................................................................................................................................... 48
4.1.5.1 SDL/DVI receiver (5DLSDL.1001-00)................................................................................................ 48
4.1.5.2 SDL3 receiver (5DLSD3.1001-00)..................................................................................................... 54
4.1.5.3 SDL4 receiver (5DLSD4.1001-00)..................................................................................................... 58
4.1.6 Equipping panels with expansion units................................................................................................... 62

Table of contents
Automation Panel 5000 User's manual V2.11 3
4.1.6.1 Button/Switching elements.................................................................................................................63
4.1.6.2 Button, switch and LED configuration............................................................................................... 63
4.1.6.3 USB interface.....................................................................................................................................64
4.1.6.4 Button/Switch interface...................................................................................................................... 65
4.1.6.5 B&R wireless assembly..................................................................................................................... 65
4.2 Individual components.................................................................................................................................. 66
4.2.1 Panels...................................................................................................................................................... 66
4.2.1.1 5AP5120.1505-000.............................................................................................................................66
4.2.1.2 5AP5120.1906-000.............................................................................................................................69
4.2.1.3 5AP5130.156B-000............................................................................................................................ 72
4.2.1.4 5AP5130.156C-000............................................................................................................................74
4.2.1.5 5AP5130.185B-000............................................................................................................................ 76
4.2.1.6 5AP5130.185C-000............................................................................................................................78
4.2.1.7 5AP5130.215C-000............................................................................................................................80
4.2.1.8 5AP5130.240C-000............................................................................................................................82
4.2.1.9 5AP5230.156B-000............................................................................................................................ 85
4.2.1.10 5AP5230.156C-000.......................................................................................................................... 88
4.2.1.11 5AP5230.185B-000.......................................................................................................................... 91
4.2.1.12 5AP5230.185C-000.......................................................................................................................... 94
4.2.1.13 5AP5230.215C-000.......................................................................................................................... 97
4.2.1.14 5AP5230.215I-000..........................................................................................................................100
4.2.1.15 5AP5230.240C-000........................................................................................................................ 103
4.2.2 Link modules......................................................................................................................................... 106
4.2.2.1 5DLSD4.1001-00..............................................................................................................................106
4.2.2.2 5DLSD3.1001-00..............................................................................................................................108
4.2.2.3 5DLSDL.1001-00..............................................................................................................................110
4.2.3 Mounting units....................................................................................................................................... 112
4.2.3.1 5ACCMA00.0000-000...................................................................................................................... 112
4.2.3.2 5ACCMA00.0001-000...................................................................................................................... 113
4.2.3.3 5ACCMA00.0002-000...................................................................................................................... 115
4.2.3.4 5ACCMA01.0100-000...................................................................................................................... 117
4.2.3.5 5ACCMA00.0100-000...................................................................................................................... 118
4.2.3.6 5ACCMA00.0101-000...................................................................................................................... 120
4.2.4 Flange.................................................................................................................................................... 122
4.2.4.1 5ACCFL00.0000-000........................................................................................................................122
4.2.4.2 5ACCFL00.0100-000........................................................................................................................124
4.2.4.3 5ACCFL00.0200-000........................................................................................................................126
4.2.5 Expansion units..................................................................................................................................... 127
4.2.5.1 5ACCKP00.xxxx-000........................................................................................................................127
4.2.5.2 5ACCKP01.xxxx-000........................................................................................................................129
4.2.5.3 5ACCKP03.xxxx-000........................................................................................................................131
4.2.5.4 5ACCKP04.xxxx-000........................................................................................................................134
4.2.5.5 5ACCKP05.xxxx-000........................................................................................................................136
4.2.5.6 5ACCKPSx.xxxx-xxx........................................................................................................................ 139
4.2.6 Handles..................................................................................................................................................140
4.2.6.1 5ACCHD0x.xxxx-000........................................................................................................................140
5 Installation and wiring.......................................................................................... 142
5.1 Basic information.........................................................................................................................................142
5.2 Automation Panel 5000 - Installation..........................................................................................................144
5.2.1 Installation with flange........................................................................................................................... 144
5.3 Removing the mounting unit cover.............................................................................................................146
5.4 Removing the link module.......................................................................................................................... 147
5.5 Installing accessories.................................................................................................................................. 148
5.5.1 Installing the handles.............................................................................................................................148
5.5.2 Installing the 5ACCFL00.0000-000 rotary flange..................................................................................149
5.5.3 Installing the 5ACCFL00.0100-000 swivel-tilt flange.............................................................................150

Table of contents
4 Automation Panel 5000 User's manual V2.11
5.5.4 Removing the swing arm mounting unit................................................................................................152
5.5.5 Installing the swing arm mounting unit..................................................................................................154
5.5.6 Removing the VESA mounting unit.......................................................................................................156
5.5.7 Installing the VESA mounting unit.........................................................................................................157
5.5.8 Uninstalling the IP54 VESA mounting unit............................................................................................158
5.5.9 Installing the IP54 VESA mounting unit................................................................................................159
5.5.10 Removing the expansion unit/cover.................................................................................................... 161
5.5.11 Installing the expansion unit/cover...................................................................................................... 163
5.5.12 Installing operating elements on the expansion cover........................................................................165
5.5.13 Replacing colored lenses.................................................................................................................... 166
5.6 Connecting to the power grid..................................................................................................................... 167
5.6.1 Installing the DC power cable............................................................................................................... 167
5.6.1.1 Wiring............................................................................................................................................... 167
5.6.2 Connecting the power supply to a B&R device.................................................................................... 168
5.6.3 Grounding concept - Functional ground................................................................................................168
5.7 Connecting cables.......................................................................................................................................169
5.7.1 Wiring with SDL cables......................................................................................................................... 169
6 Commissioning......................................................................................................170
6.1 Basic information.........................................................................................................................................170
6.2 Switching on the device for the first time................................................................................................... 170
6.2.1 General information before switching on the device.............................................................................170
6.2.2 Switching on the Automation Panel...................................................................................................... 170
6.3 Touch screen calibration............................................................................................................................. 171
6.3.1 Single-touch (analog resistive).............................................................................................................. 171
6.3.1.1 Windows 10 IoT Enterprise 2019 LTSC.......................................................................................... 171
6.3.1.2 Windows 10 IoT Enterprise 2016 LTSB.......................................................................................... 171
6.3.1.3 Windows 10 IoT Enterprise 2015 LTSB.......................................................................................... 171
6.3.1.4 Windows Embedded 8.1 Industry Pro............................................................................................. 171
6.3.1.5 Windows 7 Professional / Ultimate..................................................................................................171
6.3.1.6 Windows Embedded Standard 7 Embedded / Premium................................................................. 171
6.3.1.7 Windows XP Professional................................................................................................................171
6.3.1.8 Windows Embedded Standard 2009............................................................................................... 171
6.3.2 Multi-touch (projected capacitive - PCT)...............................................................................................172
6.3.2.1 Windows 10 IoT Enterprise 2019 LTSC.......................................................................................... 172
6.3.2.2 Windows 10 IoT Enterprise 2016 LTSB.......................................................................................... 172
6.3.2.3 Windows 10 IoT Enterprise 2015 LTSB.......................................................................................... 172
6.3.2.4 Windows Embedded 8.1 Industry Pro............................................................................................. 172
6.3.2.5 Windows 7 Professional / Ultimate..................................................................................................172
6.3.2.6 Windows Embedded Standard 7 Premium......................................................................................172
6.4 Display brightness control...........................................................................................................................173
6.4.1 Adjusting in SDL / SDL3 / SDL4 mode.................................................................................................173
6.4.2 Adjusting in DVI operation.................................................................................................................... 173
7 Software................................................................................................................. 174
7.1 Upgrade information....................................................................................................................................174
7.1.1 Firmware upgrade - Automation Panels............................................................................................... 174
7.2 Multi-touch drivers.......................................................................................................................................174
7.3 Automation Runtime....................................................................................................................................175
7.3.1 General information............................................................................................................................... 175
7.3.2 System requirements.............................................................................................................................175
7.4 Control Center.............................................................................................................................................176
7.4.1 Functions............................................................................................................................................... 176
7.4.2 Installation..............................................................................................................................................176
7.5 ADI Development Kit.................................................................................................................................. 177
7.6 ADI .NET SDK............................................................................................................................................ 178
7.7 Key Editor....................................................................................................................................................179

Table of contents
Automation Panel 5000 User's manual V2.11 5
7.8 KCF Editor...................................................................................................................................................180
7.9 HMI Service Center.................................................................................................................................... 181
7.9.1 5SWUTI.0001-000................................................................................................................................. 181
7.9.1.1 General information..........................................................................................................................181
7.9.1.2 Order data........................................................................................................................................181
8 Maintenance...........................................................................................................182
8.1 Cleaning...................................................................................................................................................... 182
8.2 User tips for increasing the service life of the display................................................................................183
8.2.1 Backlight................................................................................................................................................ 183
8.2.1.1 Measures to maintain backlight service life.....................................................................................183
8.2.2 Image persistence................................................................................................................................. 183
8.2.2.1 What causes image persistence?....................................................................................................183
8.2.2.2 How can image persistence be reduced?....................................................................................... 183
8.3 Pixel errors.................................................................................................................................................. 183
8.4 Repairs/Complaints and replacement parts................................................................................................183
9 Accessories........................................................................................................... 184
9.1 General accessories................................................................................................................................... 184
9.1.1 Accessories - Order data...................................................................................................................... 184
9.2 Power supply connectors............................................................................................................................184
9.2.1 0TB103.9x..............................................................................................................................................184
9.2.1.1 General information..........................................................................................................................184
9.2.1.2 Order data........................................................................................................................................184
9.2.1.3 Technical data..................................................................................................................................184
9.3 USB flash drives......................................................................................................................................... 186
9.3.1 5MMUSB.xxxx-01.................................................................................................................................. 186
9.3.1.1 General information..........................................................................................................................186
9.3.1.2 Order data........................................................................................................................................186
9.3.1.3 Technical data..................................................................................................................................186
9.3.1.4 Temperature/Humidity diagram........................................................................................................187
9.3.2 5MMUSB.032G-02.................................................................................................................................188
9.3.2.1 General information..........................................................................................................................188
9.3.2.2 Order data........................................................................................................................................188
9.3.2.3 Technical data..................................................................................................................................188
9.3.2.4 Temperature/Humidity diagram........................................................................................................189
9.4 Cables......................................................................................................................................................... 190
9.5 Heat pipe.....................................................................................................................................................190
9.5.1 5ACCHP00.0002-000............................................................................................................................ 190
9.5.1.1 General information..........................................................................................................................190
9.5.1.2 Order data........................................................................................................................................190
9.5.2 5ACCHP00.0003-000............................................................................................................................ 190
9.5.2.1 General information..........................................................................................................................190
9.5.2.2 Order data........................................................................................................................................190
10 International and national certifications...........................................................191
10.1 Directives and declarations.......................................................................................................................191
10.1.1 CE marking..........................................................................................................................................191
10.1.2 Radio Equipment Directive (RED).......................................................................................................191
10.1.3 EMC Directive......................................................................................................................................192
10.2 Certifications..............................................................................................................................................193
10.2.1 UL certification.....................................................................................................................................193
10.2.2 EAC......................................................................................................................................................193
10.2.3 KC........................................................................................................................................................ 193
10.2.4 RCM.....................................................................................................................................................193
10.3 Notes for the manual pursuant to radio approval.....................................................................................194

Table of contents
6 Automation Panel 5000 User's manual V2.11
11 Environmentally friendly disposal.....................................................................196
11.1 Separation of materials............................................................................................................................. 196
Appendix A Abbreviations...................................................................................... 197
Appendix B Viewing angles.................................................................................... 198
Appendix C Chemical resistance........................................................................... 199
C.1 Autotex panel overlay (polyester).............................................................................................................. 200
C.2 Coated aluminum front...............................................................................................................................200
C.3 Touch screen.............................................................................................................................................. 201
Appendix D Features............................................................................................... 202
D.1 Pushbutton RAFIX 22 FS+, 1.30.270.021/2300.........................................................................................202
D.2 Pushbutton RAFIX 22 FS+, 1.30.270.021/2500.........................................................................................202
D.3 Pushbutton RAFIX 22 FS+, 1.30.270.021/2600.........................................................................................202
D.4 Selector switch RAFIX 22 FS+, 1.30.272.102/2200.................................................................................. 202
D.5 Key switch RAFIX 22 FS+, 1.30.255.222/0000......................................................................................... 203
D.6 Emergency stop RAFIX 22 FS+ "Plus 1", 1.30.273.512/0300...................................................................203
D.7 Switching element RAFIX 22 FS universal, 1.20.126.005/0000................................................................ 203
D.8 Switching element RAFIX 22 FS+ PCB gold, 1.20.126.414/0000............................................................. 204
D.9 5ACCSE00.000x-00x..................................................................................................................................204
D.9.1 5ACCSE00.0000-000............................................................................................................................204
D.9.1.1 Pushbutton RAFIX 22 FS+, 1.30.270.921/2200..............................................................................204
D.9.1.2 Colored lens RAFIX 22 FS+, 5.49.263.062/1000........................................................................... 204
D.9.1.3 Colored lens RAFIX 22 FS+, 5.49.263.062/1300........................................................................... 205
D.9.1.4 Colored lens RAFIX 22 FS+, 5.49.263.062/1400........................................................................... 205
D.9.1.5 Colored lens RAFIX 22 FS+, 5.49.263.062/1500........................................................................... 205
D.9.1.6 Colored lens RAFIX 22 FS+, 5.49.263.062/1600........................................................................... 205
D.9.1.7 Switching element RAFIX FS, 1.20.126.102/9000..........................................................................205
D.9.2 5ACCSE00.0000-001............................................................................................................................206
D.9.2.1 Pushbutton RAFIX 22 FS+, 1.30.270.921/2200..............................................................................206
D.9.2.2 Colored lens RAFIX 22 FS+, 5.49.263.062/1000........................................................................... 206
D.9.2.3 Colored lens RAFIX 22 FS+, 5.49.263.062/1300........................................................................... 206
D.9.2.4 Colored lens RAFIX 22 FS+, 5.49.263.062/1400........................................................................... 206
D.9.2.5 Colored lens RAFIX 22 FS+, 5.49.263.062/1500........................................................................... 206
D.9.2.6 Colored lens RAFIX 22 FS+, 5.49.263.062/1600........................................................................... 207
D.9.2.7 Switching element RAFIX FS, 1.20.126.101/9000..........................................................................207
D.9.3 5ACCSE00.0001-000............................................................................................................................207
D.9.3.1 Emergency stop RAFIX 22 FS+ "Plus 1", 1.30.273.512/0300........................................................ 207
D.9.3.2 Switching element RAFIX 22 FS+ "Plus 1", 1.20.126.514/0000.....................................................208
D.9.4 5ACCSE00.0002-000............................................................................................................................208
D.9.4.1 Key switch RAFIX 22 FS+, 1.30.255.432/0000.............................................................................. 208
D.9.4.2 Switching element RAFIX 22 FS, 1.20.126.105/9000.....................................................................208
D.9.5 5ACCSE00.0003-000............................................................................................................................210
D.9.5.1 Key switch RAFIX 22 FS+, 1.30.255.222/0000.............................................................................. 210
D.9.5.2 Switching element RAFIX 22 FS, 1.20.126.103/9000.....................................................................210
D.9.6 5ACCSE00.0004-000............................................................................................................................211
D.9.6.1 Selector switch RAFIX 22 FS+, 1.30.272.102/2200....................................................................... 211
D.9.6.2 Switching element RAFIX FS, 1.20.126.102/9000..........................................................................211
D.9.7 5ACCSE00.0005-000............................................................................................................................212
D.9.7.1 USB extension RAFIX 22 FS+, 9.30.279.003/0700........................................................................212
Appendix E Touch screen....................................................................................... 213
E.1 Touch screen AMT 5-wire (single-touch)................................................................................................... 213
E.1.1 Technical data.......................................................................................................................................213

Table of contents
Automation Panel 5000 User's manual V2.11 7
E.1.2 Temperature/Humidity diagram.............................................................................................................213
E.2 3M touch screen (multi-touch generation 3).............................................................................................. 214
E.2.1 Technical data.......................................................................................................................................214
E.2.2 Temperature/Humidity diagram.............................................................................................................214

Introduction
8 Automation Panel 5000 User's manual V2.11
1 Introduction
Information:
B&R makes every effort to keep documents as current possible. The most current versions can be
downloaded from the B&R website (www.br-automation.com).
1.1 Manual history
Version Date Change
2.11 July 2020 •Updated accessories 5ACCMA00.0100-000 and 5ACCMA00.0101-000.
2.10 March 2020 •Updated accessory 5ACCMA00.0100-000.
•Updated grounding concept - Functional ground.
•Updated footnotes in the technical data of link module 5DLSDL.1001-00.
•Updated "Torques" in chapter "Installation".
•Updated cybersecurity disclaimer.
•Added description of the general limitation of USB endpoints.
•Editorial adjustments.
2.00 July 2019 •Removed register marks and directories.
•Updated date specification in the manual history.
•Revised terminology and standardization.
•Updated/Revised the following sections:
°International and national certifications
°Cybersecurity disclaimer for products
°Installation, wiring and commissioning
°Temperature/Humidity diagrams
°Block diagrams
°Device interfaces
•Updated the following:
°USB interfaces under "Individual components" > "Mounting units"
°Information about SDL4 modules
°Swivel-tilt flange
°Expansion units 5ACCKP03.xxxx-000 and 5ACCKP05.xxxx-000

Introduction
Automation Panel 5000 User's manual V2.11 9
Version Date Change
1.10 March 2018 •Updated section "Configuration" on page 18.
•Updated chapter Technical data.
•Updated the following individual components:
°"5AP5130.156C-000" on page 74
°"5AP5130.185C-000" on page 78
°"5AP5230.156C-000" on page 88
°"5AP5230.185C-000" on page 94
°"5DLSD4.1001-00" on page 106
•Updated information about installation and commissioning.
•Updated the following sections:
°"Display brightness control" on page 173
°"Adjusting in SDL / SDL3 / SDL4 mode" on page 173
°"Firmware upgrade - Automation Panels" on page 174
1.06 October 2017 •Documented expansion units "5ACCKP04.xxxx-000" on page 134.
•Documented mounting unit "5ACCMA00.0002-000" on page 115.
•Documented feature "5ACCSE00.0000-001" on page 206.
•Renamed "emergency switch-off" to "emergency stop".
•Updated the following sections:
°"Touch screen calibration" on page 171
°"Features" on page 202
°"Multi-touch drivers" on page 174
•Revised section "Installation".
•Updated the following sections:
°"Control Center" on page 176
°"ADI Development Kit" on page 177
°"ADI .NET SDK" on page 178
°"Key Editor" on page 179
°"KCF Editor" on page 180
°"HMI Service Center" on page 181
°"Repairs/Complaints and replacement parts" on page 183

Introduction
10 Automation Panel 5000 User's manual V2.11
Version Date Change
1.05 November 2016 •Renamed "display units" to "panels".
•Updated the following panels:
°"5AP5120.1505-000" on page 66
°"5AP5120.1906-000" on page 69
°"5AP5230.156B-000" on page 85
°"5AP5130.185B-000" on page 76
°"5AP5230.185B-000" on page 91
°"5AP5130.215C-000" on page 80
°"5AP5230.215I-000" on page 100
•Updated VESA mounting unit "5ACCMA01.0100-000" on page 117.
•Updated the following expansion units to 5ACCKP01.xxxx-000:
°5ACCKP01.156B-000
°5ACCKP01.185B-000
°5ACCKP01.215I-000
•Updated the following expansion covers to 5ACCKP00.xxxx-000:
°5ACCKP00.156B-000
°5ACCKP00.185B-000
°5ACCKP00.215I-000
•Updated the following handles to 5ACCHD0x.xxxx-000:
°5ACCHD00.1505-000
°5ACCHD00.185B-000
°5ACCHD00.1906-000
°5ACCHD00.215C-000
°5ACCHD01.156B-000
°5ACCHD01.185B-000
°5ACCHD01.215I-000
•Updated section "Installation".
•Updated the technical data.
•Updated the following features:
°"5ACCSE00.0000-000" on page 204
°"5ACCSE00.0001-000" on page 207
°"5ACCSE00.0002-000" on page 208
°"5ACCSE00.0003-000" on page 210
°"5ACCSE00.0004-000" on page 211
°"5ACCSE00.0005-000" on page 212
1.00 June 2016 •First version

Introduction
Automation Panel 5000 User's manual V2.11 11
1.2 Information about this document
This document is not intended for end customers! The safety guidelines required for end customers
must be incorporated into the operating instructions for end customers in the respective national lan-
guage by the machine manufacturer or system provider.
1.2.1 Organization of safety notices
Safety notices in this manual are organized as follows:
Safety notice Description
Danger! Failure to observe these safety guidelines and notices can result in death, severe injury or substantial damage to property.
Warning! Failure to observe these safety guidelines and notices can result in severe injury or substantial damage to property.
Caution! Failure to observe these safety guidelines and notices can result in injury or damage to property.
Information: These instructions are important for avoiding malfunctions.
Table 1: Description of the safety notices used in this documentation
1.2.2 Guidelines
European dimension standards apply to all dimension diagrams.
All dimensions in mm.
Unless otherwise specified, the following general tolerances apply:
Nominal dimension range General tolerance per
DIN ISO 2768 medium
Up to 6 mm ±0.1 mm
Over 6 to 30 mm ±0.2 mm
Over 30 to 120 mm ±0.3 mm
Over 120 to 400 mm ±0.5 mm
Over 400 to 1000 mm ±0.8 mm
Table 2: Nominal dimension ranges

General safety guidelines
12 Automation Panel 5000 User's manual V2.11
2 General safety guidelines
2.1 Intended use
Programmable logic controllers, operating and monitoring devices (e.g. industrial PCs, Power Panels, Mobile Pan-
els) as well as uninterruptible power supplies from B&R have been designed, developed and manufactured for
normal use in industry. They have not been designed, developed and manufactured for use that involves fatal
risks or hazards that could result in death, injury, serious physical harm or other loss without the assurance of
exceptionally stringent safety precautions. In particular, this includes the use of these systems to monitor nuclear
reactions in nuclear power plants, flight control systems, air traffic control, the control of mass transport vehicles,
medical life support systems and the control of weapon systems.
2.2 Protection against electrostatic discharge
Electrical assemblies that can be damaged by electrostatic discharge (ESD) must be handled accordingly.
2.2.1 Packaging
•Electrical assemblies with housing:
Do not require special ESD packaging but must be handled properly (see "Electrical assemblies with hous-
ing").
•Electrical assemblies without housing:
Are protected by ESD-suitable packaging.
2.2.2 Regulations for proper ESD handling
Electrical assemblies with housing
•Do not touch the connector contacts of connected cables.
•Do not touch the contact tips on circuit boards.
Electrical assemblies without housing
The following applies in addition to "Electrical assemblies with housing":
•All persons handling electrical assemblies and devices in which electrical assemblies are installed must
be grounded.
•Assemblies are only permitted to be touched on the narrow sides or front plate.
•Always place assemblies on suitable surfaces (ESD packaging, conductive foam, etc.). Metallic surfaces
are not suitable surfaces!
•Assemblies must not be subjected to electrostatic discharges (e.g. due to charged plastics).
•A minimum distance of 10 cm from monitors or television sets must be maintained.
•Measuring instruments and devices must be grounded.
•Test probes of floating potential measuring instruments must be discharged briefly on suitable grounded
surfaces before measurement.
Individual components
•ESD protective measures for individual components are implemented throughout B&R (conductive floors,
shoes, wrist straps, etc.).
•The increased ESD protective measures for individual components are not required for handling B&R
products at customer locations.
2.3 Regulations and measures
Electronic devices are generally not failsafe. If the programmable logic controller, operating or control device or
uninterruptible power supply fails, the user is responsible for ensuring that connected devices (such as motors)
are brought to a safe state.

General safety guidelines
Automation Panel 5000 User's manual V2.11 13
When using programmable logic controllers as well as when using operating and monitoring devices as control
systems in conjunction with a Soft PLC (e.g. B&R Automation Runtime or similar product) or Slot PLC (e.g. B&R
LS251 or similar product), the safety measures that apply to industrial controllers (protection by protective equip-
ment such as emergency stops) must be observed in accordance with applicable national and international regu-
lations. This also applies to all other connected devices, such as drives.
All work such as installation, commissioning and servicing are only permitted to be carried out by qualified person-
nel. Qualified personnel are persons who are familiar with the transport, installation, assembly, commissioning and
operation of the product and have the appropriate qualifications for their job (e.g. IEC 60364). National accident
prevention regulations must be observed.
The safety guidelines, information about connection conditions (nameplate and documentation) and limit values
specified in the technical data must be read carefully before installation and commissioning and must be strictly
observed.
2.4 Transport and storage
During transport and storage, devices must be protected against undue stress (mechanical stress, temperature,
humidity, aggressive atmosphere).
2.5 Installation
•The devices are not ready for use and must be installed and wired according to the requirements of this
documentation in order to comply with EMC limit values.
•Installation must be carried out according to the documentation using suitable equipment and tools.
•Devices are only permitted to be installed by qualified personnel when the power is switched off. The control
cabinet must first be disconnected from the power supply and secured against being switched on again.
•General safety regulations and national accident prevention regulations must be observed.
•The electrical installation must be carried out in accordance with relevant regulations (e.g. wire cross sec-
tion, fuse protection, protective ground connection).
2.6 Operation
2.6.1 Protection against contact with electrical parts
In order to operate programmable logic controllers, operating and monitoring devices and uninterruptible power
supplies, it is necessary for certain components to carry dangerous voltages over 42 VDC. Touching one of these
components can result in a life-threatening electric shock. There is a risk of death, serious injury or damage to
property.
Before switching on programmable logic controllers, operating and monitoring devices and uninterruptible power
supplies, it must be ensured that the housing is properly connected to ground potential (PE rail). The ground
connection must also be made if the operating and monitoring device and uninterruptible power supply are only
connected for testing purposes or only operated for a short time!
Before switching on, live parts must be securely covered. All covers must be kept closed during operation.
2.6.2 Ambient conditions - Dust, moisture, aggressive gases
The use of operating and monitoring devices (e.g. industrial PCs, Power Panels, Mobile Panels) and uninterruptible
power supplies in dusty environments must be avoided. This can otherwise result in dust deposits that affect the
functionality of the device, especially in systems with active cooling (fans), which may no longer ensure sufficient
cooling.
The presence of aggressive gases in the environment can also result in malfunctions. In combination with high
temperature and relative humidity, aggressive gases – for example with sulfur, nitrogen and chlorine components
– trigger chemical processes that can very quickly impair or damage electronic components. Blackened copper
surfaces and cable ends in existing installations are indicators of aggressive gases.
When operated in rooms with dust and condensation that can endanger functionality, operating and monitoring
devices such as Automation Panels or Power Panels are protected on the front against the ingress of dust and
moisture when installed correctly (e.g. cutout installation). The back of all devices must be protected against the
ingress of dust and moisture, however, or the dust deposits must be removed at suitable intervals.

General safety guidelines
14 Automation Panel 5000 User's manual V2.11
2.6.3 Programs, viruses and malicious programs
Any data exchange or installation of software using data storage media (e.g. floppy disk, CD-ROM, USB flash
drive) or via networks or the Internet poses a potential threat to the system. It is the direct responsibility of the user
to avert these dangers and to take appropriate measures such as virus protection programs and firewalls to protect
against them and to use only software from trustworthy sources.
2.7 Cybersecurity disclaimer for products
B&R products communicate via a network interface and were developed for secure connection with internal and,
if necessary, other networks such as the Internet.
Information:
In the following, B&R products are referred to as "product" and all types of networks (e.g. internal
networks and the Internet) are referred to as "network".
It is the sole responsibility of the customer to establish and continuously ensure a secure connection between
the product and the network. In addition, appropriate security measures must be implemented and maintained
to protect the product and entire network from any security breaches, unauthorized access, interference, digital
intrusion, data leakage and/or theft of data or information.
B&R Industrial Automation GmbH and its subsidiaries are not liable for damages and/or losses in connection
with security breaches, unauthorized access, interference, digital intrusion, data leakage and/or theft of data or
information.
The aforementioned appropriate security measures include, for example:
•Segmentation of the network (e.g. separation of the IT network from the control network1))
•Use of firewalls
•Use of authentication mechanisms
•Encryption of data
•Use of anti-malware software
Before B&R releases products or updates, they are subjected to appropriate functional testing. Independently of
this, we recommend that our customers develop their own test processes in order to be able to check the effects
of changes in advance. Such changes include, for example:
•Installation of product updates
•Significant system modifications such as configuration changes
•Deployment of updates or patches for third-party software (non-B&R software)
•Hardware replacement
These tests should ensure that implemented security measures remain effective and that systems in the customer's
environment behave as expected.
1) The term "control network" refers to computer networks used to connect control systems. The control network can be divided into zones, and there can be
several separate control networks within a company or site. The term "control systems" refers to all types of B&R products such as controllers (e.g. X20), HMI
systems (e.g. Power Panel T30), process control systems (e.g. APROL) and supporting systems such as engineering workstations with Automation Studio.

System overview
Automation Panel 5000 User's manual V2.11 15
3 System overview
3.1 Information about this user's manual
This user's manual contains all the necessary information for a functioning Automation Panel 5000 swing arm
device.
This user's manual applies to the modular Automation Panel 5000 product generation. For information about the
Panel PC 2100 or Panel PC 2200 in combination with the Automation Panel 5000, see "Panel PC 2100 support
arm devices (AP5000)" or "Panel PC 2200 support arm devices (AP5000)" user's manual.
Information:
All specifications in dimension diagrams and associated tables are in millimeters [mm].
3.2 Easy customization
The Automation Panel 5000 can be used as a remote panel or part of a Panel PC. For this, the panel is either
equipped with a receiver for Smart Display Link (SDL), SDL3 or SDL4, or a PC unit is attached. The operator panel
is always identical.

System overview
16 Automation Panel 5000 User's manual V2.11
3.3 Description of individual modules
3.3.1 AP5000 panels
The AP5000 series forms the basis for the Automation Panel 5000 and two Panel PC variants: Panel PC 2100 or
Panel PC 2200 swing arm device with Automation Panel 5000. They consist of a display and touch screen. Different
display sizes, touch screen technologies, mounting systems and panels with operating elements are available. The
panels can only be operated as a complete system in combination with a link module (Automation Panel 5000) or
a system unit (PPC2100 swing arm device or PPC2200 with Automation Panel 5000).
Single-touch panels start with model number 5AP5120.xxxx-xxx, multi-touch panels start with 5AP5130.xxxx-xxx
and multi-touch panels with an expansion option start with model number 5AP5230.xxxx-xxx.
3.3.2 Link modules
Link modules have various graphics interfaces and connections. An Automation Panel is put together by installing
a link module onto a panel.
A link module cannot be operated without a panel.
3.3.3 Mounting units
Mounting units are installed on the back of the panel. They serve to protect the installed link module / system unit,
enabling IP65, IP54, IP20 or IP10 protection for the complete system depending on its variant.
The flange is installed on swing arm mounting unit 5ACCMA00.000x-000. Due to the symmetrical design of the
back of the panel, it is possible to install the mounting unit in 2 directions. If a flange is selected for mounting, flange
output is possible towards the top or bottom.
The VESA bracket is installed on VESA mounting unit 5ACCMA01.0100-000. If a VESA bracket is selected for
mounting, VESA 100 or VESA 75 installation is possible.

System overview
Automation Panel 5000 User's manual V2.11 17
The VESA bracket is installed on IP54 VESA mounting units (5ACCMA00.0100-000 and 5ACCMA00.0101-000).
If a VESA bracket is selected as the mounting system, as with the mounting unit mentioned above, VESA 100 or
VESA 75 installation is possible.
3.3.4 Flanges
A flange is installed on the mounting unit and establishes the connection between the Automation Panel or Panel
PC and the swing arm system.
3.3.5 Expansion units
Expansion units can be installed on AP5230 panels with expansion option. It is possible to choose between an
expansion cover and an expansion unit.
Expansion covers have cutouts that can be used to install the desired operating elements at a later time.
The operating elements are already integrated in expansion units.
3.3.6 Handles
Handles can be installed on the sides of the panel to enable comfortable, ergonomic operation.

System overview
18 Automation Panel 5000 User's manual V2.11
3.4 Configuration
The following individual components are mandatory for operation as an Automation Panel 5000:
•Panel
•Link module
•Swing arm mounting unit or VESA
•Flange (swing arm mounting unit only)
•Expansion unit (only for AP5230)
Configuration
Panels Select 1
Diagonal Resolution Touch screen Keys Format
5120 panels
5AP5120.1505-000 15.0" XGA Single-touch No Landscape
5AP5120.1906-000 19.0" SXGA Single-touch No Landscape
5130 panels
5AP5130.156B-000 15.6" HD Multi-touch No Landscape
5AP5130.156C-000 15.6" FHD Multi-touch No Landscape
5AP5130.185B-000 18.5" HD Multi-touch No Landscape
5AP5130.185C-000 18.5" FHD Multi-touch No Landscape
5AP5130.215C-000 21.5" FHD Multi-touch No Landscape
5AP5130.240C-000 24.0" FHD Multi-touch No Landscape
5230 panels1)
5AP5230.156B-000 15.6" HD Multi-touch Yes Landscape
5AP5230.156C-000 15.6" FHD Multi-touch Yes Landscape
5AP5230.185B-000 18.5" HD Multi-touch Yes Landscape
5AP5230.185C-000 18.5" FHD Multi-touch Yes Landscape
5AP5230.215C-000 21.5" FHD Multi-touch Yes Landscape
5AP5230.215I-000 21.5" FHD Multi-touch Yes Portrait
5AP5230.240C-000 24.0" FHD Multi-touch Yes Landscape
Link modules Select 1
5DLSDL.1001-00 SDL/DVI receiver
5DLSD3.1001-00 SDL3 receiver
5DLSD4.1001-00 SDL4 receiver
Mounting units Select 1
Mounting unit without USB interface 5ACCMA00.0000-000
Mounting unit with USB interface 5ACCMA00.0001-000
Mounting unit with 2x USB interface 5ACCMA00.0002-000
VESA mounting unit 5ACCMA01.0100-000
IP54 VESA mounting unit 5ACCMA00.0100-000
5ACCMA00.0101-000 HMI VESA IP54 mounting unit with USB interface
Flange2) Select 1
Rotary flange 5ACCFL00.0000-000
5ACCFL00.0100-000 swivel-tilt flange
Rittal flange adapter 5ACCFL00.0200-000
Expansion units1) Select 1
5ACCKP00.156B-000
5ACCKP00.185B-000
5ACCKP00.215C-000
5ACCKP00.215I-000
5ACCKP00.240C-000
5ACCKP01.156B-000
5ACCKP01.185B-000
5ACCKP01.215C-000
5ACCKP01.215I-000
5ACCKP01.240C-000
5ACCKP04.156B-000
5ACCKP04.185B-000
5ACCKP04.215C-000
5ACCKP04.215I-000
5ACCKP04.240C-000
5ACCKP03.185B-000
5ACCKP03.215C-000
5ACCKP03.240C-000
5ACCKP05.185B-000
5ACCKP05.215C-000
5ACCKP05.240C-000
Handles3) Select 1
5ACCHD00.1505-000
5ACCHD00.156B-000
5ACCHD00.185B-000
5ACCHD00.1906-000
5ACCHD00.215C-000
5ACCHD00.240C-000
5ACCHD01.156B-000
5ACCHD01.185B-000
5ACCHD01.215C-000
5ACCHD01.215I-000
5ACCHD01.240C-000
Terminal blocks Select 1
Power supply connectors
0TB103.9
0TB103.91
1) Expansion units can only be combined with AP5230 panels.
2) A flange must be selected if a standard mounting unit is used.
3) Handles are not factory-installed and must be mounted after delivery.

System overview
Automation Panel 5000 User's manual V2.11 19
3.5 Overview
Model number Short description Page
Accessories
0TB103.9 Connector 24 VDC - 3-pin female - Screw clamp terminal block 3.31 mm² 184
0TB103.91 Connector 24 VDC - 3-pin female - Cage clamp terminal block 3.31 mm² 184
5SWUTI.0001-000 HMI Service Center USB flash drive - Hardware diagnostic software - For APC810/PPC800 - For APC910/
PPC900 - For APC2100/PPC2100 - For APC2200/PPC2200 - For APC3100/PPC3100 - For APC51x/PP500 -
For Automation Panel 800/900 - For Automation Panel 1000/5000
181
Expansion units
5ACCKP00.156B-000 AP5000 swing arm expansion option - Expansion cover - For switching elements - 10x cutouts for 22.3 mm
switching elements - For panel 5AP5230.156B/156C-000
127
5ACCKP00.185B-000 AP5000 swing arm expansion option - Expansion cover - For switching elements - 11x cutouts for 22.3 mm
switching elements - For panel 5AP5230.185B/185C-000
127
5ACCKP00.215C-000 AP5000 swing arm expansion option - Expansion cover - For switching elements - 13x cutouts for 22.3 mm
switching elements - For panel 5AP5230.215C-000
127
5ACCKP00.215I-000 AP5000 swing arm expansion option - Expansion cover - For switching elements - 7x cutouts for 22.3 mm
switching elements - For panel 5AP5230.215I-000
127
5ACCKP00.240C-000 AP5000 swing arm expansion option - Expansion cover - For switching elements - 14x cutouts for 22.3 mm
switching elements - For panel 5AP5230.240C-000
127
5ACCKP01.156B-000 AP5000 swing arm expansion option - Expansion unit - 1x emergency stop - 2x pushbutton (red and green) -
1x selector switch - 1x key switch - 1x front USB interface - For panel 5AP5230.156B/156C-000
129
5ACCKP01.185B-000 AP5000 swing arm expansion option - Expansion unit - 1x emergency stop - 2x pushbutton (red and green) -
1x selector switch - 1x key switch - 1x front USB interface - For panel 5AP5230.185B/185C-000
129
5ACCKP01.215C-000 AP5000 swing arm expansion option - Expansion unit - 1x emergency stop - 2x pushbutton (red and green) -
1x selector switch - 1x key switch - 1x front USB interface - For panel 5AP5230.215C-000
129
5ACCKP01.215I-000 AP5000 swing arm expansion option - Expansion unit - 1x emergency stop - 2x pushbutton (red and green) -
1x selector switch - 1x key switch - 1x front USB interface - For panel 5AP5230.215I-000
129
5ACCKP01.240C-000 AP5000 swing arm expansion option - Expansion unit - 1x emergency stop - 2x pushbutton (red and green) -
1x selector switch - 1x key switch - 1x front USB interface - For panel 5AP5230.240C-000
129
5ACCKP03.185B-000 AP5000 swing arm expansion option - Expansion unit - 1x RFID read/write unit - 1x emergency stop -
2x pushbutton (red and green) - 1x selector switch - 1x key switch - 1x front USB interface - For panel
5AP5230.185B/185C-000
131
5ACCKP03.215C-000 AP5000 swing arm expansion option - Expansion unit - 1x RFID read/write unit - 1x emergency stop - 2x push-
button (red and green) - 1x selector switch - 1x key switch - 1x front USB interface - For panel 5AP5230.215C-000
131
5ACCKP03.240C-000 AP5000 swing arm expansion option - Expansion unit - 1x RFID read/write unit - 1x emergency stop - 2x push-
button (red and green) - 1x selector switch - 1x key switch - 1x front USB interface - For panel 5AP5230.240C-000
131
5ACCKP04.156B-000 AP5000 swing arm expansion option - Expansion unit - 1x emergency stop - 3x pushbutton (red, green, blue)
- 1x key switch - 1x front USB interface - For panel 5AP5230.156B/156C-000
134
5ACCKP04.185B-000 AP5000 swing arm expansion option - Expansion unit - 1x emergency stop - 3x pushbutton (red, green, blue)
- 1x key switch - 1x front USB interface - For panel 5AP5230.185B/185C-000
134
5ACCKP04.215C-000 AP5000 swing arm expansion option - Expansion unit - 1x emergency stop - 3x pushbutton (red, green, blue)
- 1x key switch - 1x front USB interface - For panel 5AP5230.215C-000
134
5ACCKP04.215I-000 AP5000 swing arm expansion option - Expansion unit - 1x emergency stop - 3x pushbutton (red, green, blue)
- 1x key switch - 1x front USB interface - For panel 5AP5230.215I-000
134
5ACCKP04.240C-000 AP5000 swing arm expansion option - Expansion unit - 1x emergency stop - 3x pushbutton (red, green, blue)
- 1x key switch - 1x front USB interface - For panel 5AP5230.240C-000
134
5ACCKP05.185B-000 AP5000 swing arm expansion option - Expansion unit - 1x RFID read/write unit - 1x emergency stop - 3x
pushbutton (red, green, blue) - 1x key switch - 1x front USB interface - For panel 5AP5230.185B/185C-000
136
5ACCKP05.215C-000 AP5000 swing arm expansion option - Expansion unit - 1x RFID read/write unit - 1x emergency stop - 3x
pushbutton (red, green, blue) - 1x key switch - 1x front USB interface - For panel 5AP5230.215C-000
136
5ACCKP05.240C-000 AP5000 swing arm expansion option - Expansion unit - 1x RFID read/write unit - 1x emergency stop - 3x
pushbutton (red, green, blue) - 1x key switch - 1x front USB interface - For panel 5AP5230.240C-000
136
Flange
5ACCFL00.0000-000 AP5000 flange - Swing arm rotary flange - For swing arm mounting unit 122
5ACCFL00.0100-000 AP5000 flange - Swivel-tilt flange for swing arm - For swing arm mounting unit 124
5ACCFL00.0200-000 AP5000 flange - Swing arm flange adapter - For Rittal - For swing arm mounting unit 126
Handles
5ACCHD00.1505-000 AP5000 swing arm handles - For panel 5AP5120.1505-000 140
5ACCHD00.156B-000 AP5000 swing arm handles - For panel 5AP5130.156B-000 140
5ACCHD00.185B-000 AP5000 swing arm handles - For panel 5AP5130.185B-000 140
5ACCHD00.1906-000 AP5000 swing arm handles - For panel 5AP5120.1906-000 140
5ACCHD00.215C-000 AP5000 swing arm handles - For panel 5AP5130.215C-000 140
5ACCHD00.240C-000 AP5000 swing arm handles - For panel 5AP5130.240C-000 140
5ACCHD01.156B-000 AP5000 swing arm handles - For panel 5AP5230.156B-000 140
5ACCHD01.185B-000 AP5000 swing arm handles - For panel 5AP5230.185B-000 140
5ACCHD01.215C-000 AP5000 swing arm handles - For panel 5AP5230.215C-000 140
5ACCHD01.215I-000 AP5000 swing arm handles - For panel 5AP5230.215I-000 140
5ACCHD01.240C-000 AP5000 swing arm handles - For panel 5AP5230.240C-000 140
Heat pipe
5ACCHP00.0002-000 AP5000 heat pipe - For PPC2200 - For swing arm mounting unit 190
5ACCHP00.0003-000 HMI Heatpipe00 PPC2200+AP5000 VESA 190
Link modules
5DLSD3.1001-00 Automation Panel link module - SDL3 receiver - For Automation Panel 923/933/1000 - For Automation Panel
5000
108
5DLSD4.1001-00 Automation Panel link module - SDL4 receiver - For Automation Panel 923/933/1000 - For Automation Panel
5000
106
5DLSDL.1001-00 Automation Panel link module - SDL/DVI receiver - For Automation Panel 923/933/1000 - For Automation Panel
5000
110

System overview
20 Automation Panel 5000 User's manual V2.11
Model number Short description Page
Mounting units
5ACCMA00.0000-000 AP5000 swing arm mounting unit 112
5ACCMA00.0001-000 AP5000 swing arm mounting unit - 1x rear USB interface 113
5ACCMA00.0100-000 HMI mounting unit VESA IP54 - Leak tightness is only provided with suitable cable grommets. 118
5ACCMA00.0101-000 HMI mounting unit VESA IP54 w/USB - Leak tightness is only provided with suitable cable grommets. 120
5ACCMA01.0100-000 AP5000 VESA mounting unit IP20 117
Panels
5AP5120.1505-000 Automation Panel 15.0" XGA TFT - 1024 x 768 pixels (4:3) - Single-touch (analog resistive) - Swing arm mount-
ing - Landscape format - For PPC2100 / PPC2200 / link modules
66
5AP5120.1906-000 Automation Panel 19.0" SXGA TFT - 1280 x 1024 pixels (5:4) - Single-touch (analog resistive) - Swing arm
mounting - Landscape format - For PPC2100 / PPC2200 / link modules
69
5AP5130.156B-000 Automation Panel 15.6" HD TFT - 1366 x 768 pixels (16:9) - Multi-touch (projected capacitive) - Swing arm
mounting - Landscape format - For PPC2100 / PPC2200 / link modules
72
5AP5130.156C-000 Automation Panel 15.6" Full HD TFT - 1920 x 1080 pixels (16:9) - Multi-touch (projected capacitive) - Swing
arm mounting - Landscape format - For PPC2100 / PPC2200 / link modules
74
5AP5130.185B-000 Automation Panel 18.5" HD TFT - 1366 x 768 pixels (16:9) - Multi-touch (projected capacitive) - Swing arm
mounting - Landscape format - For PPC2100 / PPC2200 / link modules
76
5AP5130.185C-000 Automation Panel 18.5" Full HD TFT - 1920 x 1080 pixels (16:9) - Multi-touch (projected capacitive) - Swing
arm mounting - Landscape format - For PPC2100 / PPC2200 / link modules
78
5AP5130.215C-000 Automation Panel 21.5" Full HD TFT - 1920 x 1080 pixels (16:9) - Multi-touch (projected capacitive) - Swing
arm mounting - Landscape format - For PPC2100 / PPC2200 / link modules
80
5AP5130.240C-000 Automation Panel 24.0" Full HD TFT - 1920 x 1080 pixels (16:9) - Multi-touch (projected capacitive) - Swing
arm mounting - Landscape format - For PPC2100 / PPC2200 / link modules
82
5AP5230.156B-000 Automation Panel 15.6" HD TFT - 1366 x 768 pixels (16:9) - Multi-touch (projected capacitive) - Swing arm
mounting - Landscape format - Expansion option - For PPC2100 / PPC2200 / link modules
85
5AP5230.156C-000 Automation Panel 15.6" Full HD TFT - 1920 x 1080 pixels (16:9) - Multi-touch (projected capacitive) - Swing
arm mounting - Landscape format - Expansion option - For PPC2100 / PPC2200 / link modules
88
5AP5230.185B-000 Automation Panel 18.5" HD TFT - 1366 x 768 pixels (16:9) - Multi-touch (projected capacitive) - Swing arm
mounting - Landscape format - Expansion option - For PPC2100 / PPC2200 / link modules
91
5AP5230.185C-000 Automation Panel 18.5" Full HD TFT - 1920 x 1080 pixels (16:9) - Multi-touch (projected capacitive) - Swing
arm mounting - Landscape format - Expansion option - For PPC2100 / PPC2200 / link modules
94
5AP5230.215C-000 Automation Panel 21.5" Full HD TFT - 1920 x 1080 pixels (16:9) - Multi-touch (projected capacitive) - Swing
arm mounting - Landscape format - Expansion option - For PPC2100 / PPC2200 / link modules
97
5AP5230.215I-000 Automation Panel 21.5" Full HD TFT - 1920 x 1080 pixels (16:9) - Multi-touch (projected capacitive) - Swing
arm mounting - Portrait format - Expansion option - For PPC2100 / PPC2200 / link modules
100
5AP5230.240C-000 Automation Panel 24.0" Full HD TFT - 1920 x 1080 pixels (16:9) - Multi-touch (projected capacitive) - Swing
arm mounting - Landscape format - Expansion option - For PPC2100 / PPC2200 / link modules
103
Swing arm mounting units
5ACCMA00.0002-000 AP5000 swing arm mounting unit - 2x rear USB interface 115
USB accessories
5MMUSB.032G-02 USB 3.0 flash drive 32 GB MLC 188
5MMUSB.2048-01 USB 2.0 flash drive 2048 MB B&R 186
5MMUSB.4096-01 USB 2.0 flash drive 4096 MB B&R 186