Banner SureCross Performance FlexPower DX80G9M2S-P7 User manual

The SureCross® wireless system is a radio frequency network with integrated I/O that can
operate in most environments and eliminate the need for wiring runs. Wireless networks are
formed around a Gateway, which acts as the wireless network master device, and one or
more Nodes.
• Wireless industrial I/O device with up to 12 sinking discrete inputs or outputs. Default
configuration is set to 6 inputs and 6 outputs (without bit-packing)
• Selectable transmit power levels of 250 mW or 1 Watt and license-free operation up to 4
watt EIRP, with a high-gain antenna, in the U.S. and Canada for 900 MHz
• Power options allow for +10 to 30V dc or solar for low power applications; this model is
not recommended for DX81 or DX81P6 battery-powered operations
• DIP switches for user configuration
• Modbus serial interface
• Site Survey analyzes the network’s signal strength and reliability and displays the re-
sults on the Gateway's LCD
• Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple
Access (TDMA) control architecture ensure reliable data delivery within the unlicensed
Industrial, Scientific, and Medical (ISM) band
• Transceivers provide bidirectional communication between the Gateway and Node, in-
cluding fully acknowledged data transmission
• Lost RF links are detected and relevant outputs set to user-defined conditions
For additional information, the most recent version of all documentation, and a complete list of accessories, refer to Banner Engineering's
website, www.bannerengineering.com/surecross.
Models Frequency Power I/O
DX80G9M2S-P7 900 MHz ISM
Band +10 to 30V dc or solar power (this model is
not recommended for DX81 or DX81P6 bat-
tery-powered operation)
Discrete I/O: Up to 12 sinking inputs or up to 12
NMOS sinking outputs (for a total of 12 I/O)
(Default configuration is 6 IN and 6 OUT, without
bit-packing)
DX80G2M2S-P7 2.4 GHz ISM
Band
DX80...C (IP20; NEMA 1) models are also available. To order this model with an IP20 housing, add a C
to the end of the model number: DX80G9M2S-P7C.
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to serious
injury or death. This device does NOT include the self-checking redundant circuitry necessary to allow its
use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-
energized sensor output condition.
CAUTION: Never Operate 1 Watt Radios Without Antennas
To avoid damaging the radio circuitry, never power up SureCross Performance or SureCross MultiHop (1
Watt) radios without an antenna.
The SureCross® Performance Wireless Network
SureCross Performance FlexPower Gateway
P/N 155285_web
Rev. D
3/14/2013

The SureCross® Performance wireless I/O network provides reliable monitoring without the burden of wiring or conduit installation. The
SureCross wireless network can operate independently or in conjunction with a host system, PLC, and/or PC software.
Each wireless network system consists of one Gateway and one or more Nodes. Devices ship with factory defined inputs and outputs
that may be all discrete, all analog, or a mix of discrete and analog I/O.
Gateway
Node
Node
FlexPower Node with
integrated battery
The SureCross® Performance network is a deterministic system—the network identifies when the radio signal is lost and drives relevant
outputs to user-defined conditions. Once the radio signal is reacquired, the network returns to normal operation.
SureCross® Performance Gateways and Nodes
A Gateway is the master device within each radio network. Every wireless network must have one Gateway that schedules communica-
tion traffic and controls the I/O configuration for the network. A radio network contains only one Gateway, but can contain many Nodes.
Similar to how a gateway device on a wired network acts as a “portal” between networks, the SureCross Gateway acts as the portal
between the wireless network and the host controller. When the Gateway, using its Modbus RTU RS-485 connection, is a Modbus slave
to a Modbus RTU host controller, the wireless network may contain up to 47 Nodes in a single wireless network and the Gateway holds
the Modbus registers of all wireless devices within the network.
A Node is a wireless network end-point device used to provide sensing capability in a remote area or factory. The Node collects data
from sensors and communicates the data back to the Gateway. Nodes are available in a wide variety of power or input/output options.
Each Node device can be connected to sensors or output devices and reports I/O status to the Gateway.
SureCross User Configuration Tool
The User Configuration Tool (UCT) offers an easy way to link I/O points in your
wireless network, view I/O register values graphically, and set system communi-
cation parameters when a host system is not part of the wireless network.
The UCT requires a special USB to RS-485 (model number BWA-UCT-900 for 1
Watt radios, BWA-HW-006 can be used for all other radios) converter cable to
pass information between your computer and the Gateway. Download the most
recent revisions of the UCT software from Banner Engineering's website: http://
www.bannerengineering.com/wireless.
Setting Up Your Wireless Network
To set up and install your wireless network, follow these steps:
1. Configure the DIP switches of all devices.
2. Connect the sensors to the SureCross devices.
3. Apply power to all devices.
4. Form the wireless network by binding the Nodes to the Gateway. If the binding instructions are not included in the datasheet, refer to
the product manual for binding instructions.
5. Observe the LED behavior to verify the devices are communicating with each other.
SureCross Performance FlexPower Gateway
2 www.bannerengineering.com - tel: [phone] P/N 155285_web
Rev. D

6. Conduct a site survey between the Gateway and Nodes. If the site survey instructions are not included in this datasheet, refer to the
product manual for detailed site survey instructions.
7. Install your wireless sensor network components. If installation instructions are not included in this datasheet, refer to the product
manual for detailed installation instructions.
For additional information, including installation and setup, weatherproofing, device menu maps, troubleshooting, and a list of accesso-
ries, refer to one of the following product manuals.
• SureCross Quick Start Guide: Banner part number 128185
• SureCross Wireless I/O Network Manual: 132607
• Web Configurator Manual (used with "Pro" and DX83 models): 134421
• Host Configuration Manual 132114
Configuring the DIP Switches
Before making any changes to the DIP switch positions, disconnect the power. For devices with batteries integrated into the housing,
remove the battery for at least one minute. DIP switch changes will not be recognized if power isn't cycled to the device.
For parameters not set via DIP switches, use the User Configuration Tool (UCT) to make configuration changes. For parameters set
using the DIP switches, the DIP switch positions override any changes made using the User Configuration Tool.
Accessing the Internal DIP Switches
To access the internal DIP switches, follow these steps:
1. Unscrew the four screws that mount the cover to the bottom housing.
2. Remove the cover from the housing without damaging the ribbon cable or the pins the cable plugs into.
3. Gently unplug the ribbon cable from the board mounted into the bottom housing. For integrated battery models (no ribbon cable) and
Class I, Division 2 certified devices (ribbon cable is glued down), skip this step.
4. Remove the black cover plate from the bottom of the device's cover.
The DIP switches are located behind the rotary dials.
After making the necessary changes to the DIP switches, place the black cover plate back into position and
gently push into place. Plug the ribbon cable in after verifying that the blocked hole lines up with the missing
pin. Mount the cover back onto the housing.
DIP Switch Settings
Switches
Device Settings 1 2 3 4 5 6 7 8
Transmit power level: 1 Watt (30 dBm) OFF*
Transmit power level: 250 mW (24 dBm), DX80
compatibility mode
ON
Modbus or UCT configured (overrides switches
5-8)
OFF*
DIP switch configured (Uses 5-8 for I/O configura-
tion)
ON
12 inputs, 0 outputs OFF* OFF* OFF* OFF*
11 inputs, 1 output OFF OFF OFF ON
10 inputs, 2 outputs OFF OFF ON OFF
9 inputs, 3 outputs OFF OFF ON ON
8 inputs, 4 outputs OFF ON OFF OFF
SureCross Performance FlexPower Gateway
P/N 155285_web
Rev. D
www.bannerengineering.com - tel: [phone]

Switches
Device Settings 1 2 3 4 5 6 7 8
7 inputs, 5 outputs OFF ON OFF ON
6 inputs, 6 outputs OFF ON ON OFF
5 inputs, 7 outputs OFF ON ON ON
4 inputs, 8 outputs ON OFF OFF OFF
3 inputs, 9 outputs ON OFF OFF ON
2 inputs, 10 outputs ON OFF ON OFF
1 input, 11 outputs ON OFF ON ON
0 inputs, 12 outputs ON ON OFF OFF
6 inputs, 6 outputs (non bit-packed) ON ON OFF ON
8 bit-packed inputs, 4 non bit-packed outputs ON ON ON OFF
4 non bit-packed inputs, 8 bit-packed outputs ON ON ON ON
* Default configuration
For the 6 IN/6 OUT non bit-packed configuration, the discrete INs use I/O points 1 through 6 and the discrete OUTs use I/O points 9
through 14. For the 8 bit-packed IN/4 non bit-packed OUT configuration, all discrete INs use I/O point 1 and the discrete OUTs use I/O
points 9 through 12. For the 4 non bit-packed IN/8 bit-packed output configuration, the discrete INs use I/O points 1 through 4 and all bit-
packed outputs use I/O point 9.
Modbus/UCT Configured or DIP Switch Configured for I/O Configuration
In the OFF position, this device is configured for six discrete inputs and six discrete outputs (non-bit packed) for products built after May
2011. For products built before May 2011, this default position configures the device for 12 inputs and zero outputs (bit packed). In the
OFF position, users can send commands directly from the host system to the devices to select custom I/O configuration. Users may also
use the User Configuration Tool (UCT) to write custom configuration
In the ON position, use DIP switches 5 through 8 to select one of the pre-programmed discrete I/O configurations shown in the DIP
Switch Settings table.
Transmit Power Levels
The 900 MHz radios can be operated at 1 watt (30 dBm) or 250 mW (24 dBm). While the radios operate in 1 Watt mode, they cannot
communicate with 150 mW DX80 radio devices. To communicate with the 150 mW radio models, operate this radio in 250 mW mode.
For 2.4 GHz radios, this DIP switch is disabled. The transmit power for 2.4 GHz is fixed at about 100 mW EIRP (18 dBm), making the 2.4
GHz Performance models automatically compatible with the DX80 2.4 GHz models.
Mixing Performance and Non-Performance Radios in the Same Network
To comply with federal regulations, the 150 mW radios and 1 Watt radios communicate differently. To mix Performance radios with non-
Performance radios:
• Performance radios must operate in 250 mW mode, not 1 Watt mode (DIP switch 1 ON)
• Non-Performance radios must be set to use Extended Address Mode (DIP switch 1 ON)
For more detailed instructions about setting up your wireless network, refer to the Quick Start Guide, Banner document number 128185.
For more information about using Performance and non-Performance radios within the same network, refer the technical note titled
Mixing Performance Radios and 150 mW Radios in the Same Networklisted on the FAQ/Knowledgebase section of Banner's Wireless
Sensor Networks website.
Wiring Your SureCross® Device
Use the following wiring diagrams to first wire the sensors and then apply power to the SureCross devices.
5-pin Euro-Style Hookup for the FlexPower Gateway
Connecting dc power to the communication pins will cause permanent damage. For FlexPower devices, do not apply more than 5.5V to
the gray wire.
SureCross Performance FlexPower Gateway
4 www.bannerengineering.com - tel: [phone] P/N 155285_web
Rev. D

Wire No. Wire Color
1
2
3
4
5
1 Brown 10 to 30V dc
2 White RS485 / D1 / B / +
3 Blue dc common (GND)
4 Black RS485 / D0 / A / –
5 Gray 3.6 to 5.5V dc
Terminal Blocks and Wiring (12 Sinking I/O Models)
PWR
GND
IO7
IO8
IO9
IO10
IO11
IO12
PWR
GND
IO6
IO5
IO4
IO3
IO2
IO1
IOx. Input or output (depending on configuration)
GND. Ground/dc common connection.
PWR. Power, 10 to 30V dc power connection.
For the default configuration of 6 IN and 6 OUT, use IO 1 through 6 to wire
the inputs and IO 7 through 12 to wire the outputs.
When using the DIP switches to configure the input and output selection,
wire the inputs beginning with IO1. After all inputs are wired, begin using
the remaining IOx as outputs. For example, if you are using 10 inputs and 2
outputs, use terminals IO1 through 10 for the inputs and terminals IO 11
and 12 for the outputs.
12 I/O Sinking Models
Discrete Input Wiring for NPN Sen-
sors
Discrete Output Wiring (NPN or NMOS)
DIx
GND
dc common
DOx
GND
PWR
10-30V dc
Load
dc common
The DIx and DOx of these wiring diagrams
correspond to the IOx on the terminal
block.
DX80...C Wiring
Wiring power to the DX80...C models varies depending the power requirements of the model.
Terminal Label Gateway, DX85 10 to 30V dc Powered Nodes Battery Powered Nodes
V+ 10 to 30V dc 10 to 30V dc
Tx/+ RS485 / D1 / B / +
V- dc common (GND) dc common (GND) dc common (GND)
Rx/- RS485 / D0 / A / -
B+ 3.6 to 5.5V dc
Connecting dc power to the communication pins (Tx/Rx) will cause permanent damage. For FlexPower devices, do not apply more than
5.5V to the gray wire.
Terminal Blocks (IP20 Base)
This is the wiring board for the DX80**X2S-P7C IP20 models.
For the default configuration of 6 IN and 6 OUT, use IO 1 through 6 to wire the inputs and IO 7 through 12 to wire the outputs.
When using the DIP switches to configure the input and output selection, wire the inputs beginning with IO1. After all inputs are wired,
begin using the remaining IOx as outputs. For example, if you are using 10 inputs and 2 outputs, use terminals IO1 through 10 for the
inputs and terminals IO 11 and 12 for the outputs.
SureCross Performance FlexPower Gateway
P/N 155285_web
Rev. D
www.bannerengineering.com - tel: [phone]

IO5
IO6
IO7
IO8
IO1
IO3
V-
V-
V+
B+
IO4
IO2
IO9
IO10
IO11
IO12
Tx/+ NC
Rx/- NC
IOx. Input or output (depending on configuration)
NC. No connection (Nodes)
RX/-. Serial comms line (Gateway and DX85 models)
TX/+. Serial comms line (Gateway and DX85 models)
V+. Power, 10 to 30V dc power connection.
V-. Ground/dc common connection.
LED Behavior for the Gateways
After powering up and binding the Gateway and its Nodes, verify all devices are communicating properly. When testing communication
between the Gateway and Node, all radios and antennas should be at least two meters apart or the communications may fail. This table
lists the LED behavior for the Gateway models with two LEDs.
LED 1 LED 2 Gateway Status
(solid green) Power ON
(flashing red) (flashing red) Device Error
(flashing yellow) Modbus Communication Active
(flashing red) Modbus Communication Error
For Gateway and Ethernet Bridge systems, active Modbus communication refers to the communication between the Gateway and the
Ethernet Bridge. For GatewayPro systems, the Modbus communication LEDs refer to the communication internal to the GatewayPro. For
Gateway only systems, the Modbus communication LEDs refer to the communication between the Gateway and its host system (if appli-
cable).
Modbus Register Table
I/O
Poin
t
Modbus Holding Register I/O Type
I/O Range
Holding Regis-
ter Representa-
tion
Terminal
Block Labels
Gateway or
DX85
Any Node Min.
Value
Max.
Value
Min.
(Dec.)
Max.
(Dec.)
1 1 1 + (Node# × 16) Bit-Packed Discrete IN 0 1 0 1 IO1 to IO12
2 2 2 + (Node# × 16)
Non Bit-Packed Discrete IN (de-
pending on DIP switch configura-
tion)
3 3 3 + (Node# × 16)
4 4 4 + (Node# × 16)
5 5 5 + (Node# × 16)
6 6 6 + (Node# × 16)
7 7 7 + (Node# × 16) Reserved
8 8 8 + (Node# × 16) Device Message
9 9 9 + (Node# × 16) Bit-Packed Discrete OUT 0 1 0 1 IO1 to IO12
SureCross Performance FlexPower Gateway
6 www.bannerengineering.com - tel: [phone] P/N 155285_web
Rev. D

I/O
Poin
t
Modbus Holding Register I/O Type
I/O Range
Holding Regis-
ter Representa-
tion
Terminal
Block Labels
Gateway or
DX85
Any Node Min.
Value
Max.
Value
Min.
(Dec.)
Max.
(Dec.)
10 10 10 + (Node# × 16)
Non Bit-Packed Discrete OUT (de-
pending on DIP switch configura-
tion)
11 11 11 + (Node# × 16)
12 12 12 + (Node# × 16)
13 13 13 + (Node# × 16)
14 14 14 + (Node# × 16)
15 15 15 + (Node# × 16) Control Message
16 16 16 + (Node# × 16) Reserved
User Defined Configuration of Discrete I/O on the 12 I/O Devices
The 12 I/O device can be configured into any combination of 12 discrete inputs or outputs. Inputs are stored in a bit packed form in I/O
point 1, device register 1. Outputs are stored in a bit packed form in I/O point 9, device register 9. (See Modbus Register Block table on
previous page.)
Defining Inputs and Outputs
To define which of the 12 I/O points are inputs, adjust the bit field stored as I/O 1’s threshold parameter [15:0]. Set bit 0 of the 16-bit
parameter data word to define I/O 1 as an input, set bit 1 to define I/O 2 as an input, et cetera. Each bit position of the parameter is
associated to a I/O point. In the example below, the first five I/O points are defined as inputs.
Input Pa-
rameter
Bit 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
Input Point # 12 11 10 9 8 7 6 5 4 3 2 1
Parameter
Data
0 0 0 0 0 0 0 1 1 1 1 1
Define outputs the same way by adjusting the bit field stored in I/O 9's threshold parameter [15:0]. Verify the bit pattern for outputs does
not overlap the input pattern. In the example below, I/O points 6-12 are set as outputs.
Input Pa-
rameter
Bit 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
Input Point # 12 11 10 9 8 7 6 5 4 3 2 1
Parameter
Data
1 1 1 1 1 1 1 0 0 0 0 0
For inputs, the first I/O point selected as an input is placed in bit position 0 in register 1. The second input point is in bit position 1, et
cetera. Likewise, for outputs, the first I/O point selected as an output is placed in bit position 0 in register 9, the second input point is in bit
position 2. The bit-packed values are stored in right-justified format.
Input Pa-
rameter
Bit 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00
Input Point # 0 0 0 0 0 0 0 IN 5 IN 4 IN 3 IN 2 IN 1
Parameter
Data
0 0 0 0 0 OU
T 7
OUT
6
OUT
5
OU
T 4
OUT
3
OU
T 2
OUT
1
SureCross Performance FlexPower Gateway
P/N 155285_web
Rev. D
www.bannerengineering.com - tel: [phone]

Defining Inputs and Outputs Using the UCT
To configure either a Gateway or Node, select the Gateway or specific Node from the dropdown list. To configure a DX85 Remote I/O
model, set the DX85's Slave ID to 01 and select the Gateway from the dropdown list.
To define which of the 12 I/O points are inputs for the selected device, adjust the threshold parameter for I/O point 1. Set bit 0 of the 16-
bit parameter data word to define I/O 1 as an input, set bit 1 to define I/O 2 as an input, et cetera. Each bit position of the parameter is
associated to a I/O point. In the example below, the first five I/O points are defined as inputs (0000 0001 1111 = 0x001F = 0031).
To define which of the 12 I/O points are outputs for the selected device, adjust the threshold parameter for I/O point 9. In the example
below, bits 11 through 5 are used to set seven outputs (1111 1110 0000 = 0x0FE0 = 4064)
Storage Mode and Sleep Mode
While in storage mode, the radio does not operate. All SureCross® radios powered from an integrated battery ship from the factory in
storage mode to conserve the battery. To wake the device, press and hold button 1 for five seconds. To put any FlexPower® or integra-
ted battery SureCross radio into storage mode, press and hold button 1 for five seconds. The radio is in storage mode when the LEDs
stop blinking, but in some models, the LCD remains on for an additional minute after the radio enters storage mode. After a device has
entered storage mode, you must wait one minute before waking it.
During normal operation, the SureCross radio devices enter sleep mode after 15 minutes of operation. The radio continues to function,
but the LCD goes blank. To wake the device, press any button.
Specifications
Radio General
Radio Range
900 MHz (1 Watt): Up to 9.6 kilometers (6 miles) *
2.4 GHz: Up to 3.2 kilometers (2 miles) *
Radio Transmit Power
Power*
Requirements: +10 to 30V dc or 3.6 to 5.5V dc low
power option (For European applications: +10 to 24V
dc, ± 10% or 3.6 to 5.5V dc low power option)
SureCross Performance FlexPower Gateway
8 www.bannerengineering.com - tel: [phone] P/N 155285_web
Rev. D

Radio General
900 MHz (1 Watt): 30 dBm conducted (up to 36 dBm
EIRP)
2.4 GHz: 18 dBm conducted, less than or equal to 20
dBm EIRP
900 MHz Compliance (1 Watt Radios)
FCC ID UE3RM1809: This device complies with FCC
Part 15, Subpart C, 15.247
IC: 7044A-RM1809
2.4 GHz Compliance
FCC ID UE300DX80-2400 - This device complies with
FCC Part 15, Subpart C, 15.247
ETSI/EN: In accordance with EN 300 328: V1.7.1
(2006-05)
IC: 7044A-DX8024
Spread Spectrum Technology
FHSS (Frequency Hopping Spread Spectrum)
Link Timeout
Gateway: Configurable
Node: Defined by Gateway
* With the 2 dB antenna that ships with the product. High-gain an-
tennas are available, but the range depends on the environment
and line of sight. To determine the range of your wireless network,
perform a Site Survey.
900 MHz Consumption: Maximum current draw is <100
mA and typical current draw is <50 mA at 24V dc. (2.4
GHz consumption is less.)
Housing
Polycarbonate housing and rotary dial cover; polyester
labels; EDPM rubber cover gasket; nitrile rubber, non-
sulphur cured button covers
Weight: 0.26 kg (0.57 lbs)
Mounting: #10 or M5 (SS M5 hardware included)
Max. Tightening Torque: 0.56 N·m (5 lbf·in)
Antenna Connection
Ext. Reverse Polarity SMA, 50 Ohms
Max Tightening Torque: 0.45 N·m (4 lbf·in)
Interface
Indicators: Two bi-color LEDs
Buttons: Two
Display: Six character LCD
Wiring Access
DX80 models: Four PG-7, One 1/2-inch NPT, One 5-
pin Euro-style male connector
DX80...C models: External terminals
* For European applications, power the DX80 from a Limited Pow-
er Source as defined in EN 60950-1.
Inputs Outputs
Discrete Inputs
Rating: 3 mA max current at 30V dc
Sample Rate: Up to 62.5 milliseconds
Report Rate: On change of state
ON Condition (NPN): Less than 0.7V
OFF Condition (NPN): Greater than 2V or open
Discrete Outputs
Update Rate: Up to 62.5 milliseconds
Output State Following Timeout: OFF
ON Condition (NMOS): Less than 0.7V
OFF Condition (NMOS): Open
Discrete Output Rating (12 I/O NMOS)
Less than 100 mA max current at 30V dc
ON-State Saturation: Less than 0.7V at 20 mA
Communication Environmental
Hardware (RS-485)
Interface: 2-wire half-duplex RS-485
Baud rates: 9.6k, 19.2k (default), or 38.4k
Data format: 8 data bits, no parity, 1 stop bit
Protocol
Modbus RTU
Ratings
Rating for DX80 models: IEC IP67; NEMA 6; (See UL
section below for any applicable UL specifications)
Rating for DX80...C models: IEC IP20; NEMA 1
Conditions
Operating Temperature: −40 to +85° C (Electronics);
−20 to +80° C (LCD)
Operating Humidity: 95% max. relative (non-condens-
ing)
Radiated Immunity: 10 V/m, 80-2700 MHz
(EN61000-6-2)
Shock and Vibration
IEC 68-2-6 and IEC 68-2-7
Shock: 30g, 11 millisecond half sine wave, 18 shocks
SureCross Performance FlexPower Gateway
P/N 155285_web
Rev. D
www.bannerengineering.com - tel: [phone]

Communication Environmental
Vibration: 0.5 mm p-p, 10 to 60 Hz
Refer to the SureCross® DX80 Wireless I/O Network product manual, Banner p/n 132607, for installation and waterproofing instructions.
Operating the devices at the maximum operating conditions for extended periods can shorten the life of the device.
Included with Model
The following items ship with the DX80 radios.
• BWA-HW-002: DX80 Access Hardware Kit, containing four PG-7 plastic threaded plugs, four PG-7 nylon gland fittings, four PG-7 hex
nuts, one 1/2-inch NPT plug, and one 1/2-inch nylon gland fitting. (Not included with IP20 DX80...C models)
• BWA-HW-001: Mounting Hardware Kit, containing four M5-0.8 x 25mm SS screws, four M5-0.8 x 16mm SS screws, four M5-0.8mm
SS hex nuts, and four #8-32 x 3/4" SS bolts
• BWA-HW-003: PTFE tape
• BWA-9O2-C (900 MHz) or BWA-2O2-C (2.4 GHz): Antenna, 2 dBd Omni, Rubber Swivel RP-SMA Male. (Not included with Internal
antenna models)
• Quick Start Guide (128185 for DX80 Gateways or 152653 for MultiHop models)
• MQDC1-506: 5-Euro (single ended) straight cable, 2m (Not included with FlexPower devices)
• BWA-HW-011: IP20 Screw Terminal Headers (2 pack) (Included only with the IP20 DX80...C models)
Warnings
The manufacturer does not take responsibility for the violation of any warning listed in this document. Make no modifications to this
product. Any modifications to this product not expressly approved by Banner Engineering could void the user’s authority to operate the
product. All specifications published in this document are subject to change. Banner reserves the right to modify product specifica-
tions or to update documentation at any time. For the most recent version of any documentation, refer to: www.bannerengineering.com.
© 2006-2013 Banner Engineering Corp. All rights reserved.
Antenna Installation
Install and properly ground a qualified surge suppressor when installing a remote antenna system. Remote antenna configurations instal-
led without surge suppressors invalidate the manufacturer's warranty. Keep the ground wire as short as possible and make all ground
connections to a single-point ground system to ensure no ground loops are created. No surge suppressor can absorb all lightning strikes.
Do not touch the SureCross® device or any equipment connected to the SureCross device during a thunderstorm.
Exporting SureCross Radios
It is our intent to fully comply with all national and regional regulations regarding radio frequency emissions. Customers who want to re-
export this product to a country other than that to which it was sold must ensure the device is approved in the destination
country. A list of approved countries appears in the Agency Certifications section of the product manual. The SureCross wireless prod-
ucts were certified for use in these countries using the antenna that ships with the product. When using other antennas, verify you are not
exceeding the transmit power levels allowed by local governing agencies. Consult with Banner Engineering if the destination country is
not on this list.
Banner Engineering Corp Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of
shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned
to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse,
abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (IN-
CLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND
WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL
BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPEN-
SES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY
PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WAR-
RANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or
liabilities relating to any product previously manufactured by Banner Engineering Corp.
SureCross Performance FlexPower Gateway
www.bannerengineering.com - tel: [phone]