Barco MDRC-1119 TS User manual

MDRC-1119
MDRC-2120
User manual

2
Copyright notice
This document is copyrighted. All rights are reserved. Nor this
document, nor any part of it, may be reproduced or copied in any form
or by any means - graphical, electronic, or mechanical including
photocopying, taping or information storage and retrieval systems -
without written permission of Barco
© 2014 Barco N.V. All rights reserved.

3
Table of Contents
Table of Contents ....................................................................................... 3
Preface........................................................................................................ 5
Important notice.................................................................................... 5
Environmental information................................................................... 6
Recommendations for using your display system.............................10
Unpacking and handling tips ..............................................................12
Preventing fire and injury................................................................... 13
Cleaning the display............................................................................13
Shipping/storing the display..............................................................14
Explanation of symbols.......................................................................15
Introduction.............................................................................................. 16
About the product ...............................................................................16
Package Overview............................................................................... 18
Installation................................................................................................ 19
Product Overview................................................................................19
Front View.......................................................................................19
Back View .......................................................................................20
Tilt ........................................................................................................21
Kensington Security Slot ................................................................21
Start Your Installation.......................................................................... 21
Connecting the Display ..................................................................22
Adjusting the screen position.............................................................24
User Controls ............................................................................................25
Jog Dial Controls ..................................................................................25
How to Use the OSD Menus................................................................ 26
On-Screen Display Menus ...................................................................27
Appendix ..................................................................................................45
Troubleshooting...................................................................................45
Warning Signal ....................................................................................46
Product Dimensions MDRC-1119/MDRC-1119 TS/MDRC-1119 HB...47
Technical specifications MDRC-1119 ..................................................48
Technical specifications MDRC-1119 TS.............................................. 50
Technical specifications MDRC-1119 HB............................................. 52
Compatibility Modes MDRC -1119/MDRC-1119 TS/MDRC-1119 HB. 54
Product Dimensions MDRC-2120........................................................56

4
Technical specifications MDRC-2120 ..................................................57
Compatibility Modes MDRC-2120.......................................................59
Regulatory Compliance.......................................................................60

5
Preface
Important notice
Notice
Although every attempt has been made to achieve technical accuracy
in this document, we assume no responsibility for errors that may be
found. Our goal is to provide you with the most accurate and usable
documentation possible; if you discover errors, please let us know.
Barco software products are the property of Barco. They are distributed
under copyright by Barco N.V., for use only under the specific terms of
a software license agreement between Barco N.V. and the licensee.
No other use, duplication, or disclosure of a Barco software product, in
any form, is authorized.
The specifications of Barco products are subject to change without
notice.
Trademarks
All trademarks and registered trademarks are property of their
respective owners.

6
Environmental information
Disposal Information
The lamps inside the display contain mercury. Do not throw the display
in the trash. Dispose of it as required by local ordinances or regulations.
This equipment has required the extraction and use of natural
resources for its production. It may contain hazardous substances for
health and environment.
In order to avoid the dissemination of those substances in the
environment and to diminish the pressure on natural resources, we
encourage you to use the appropriate take-back systems.
Those systems will reuse or recycle most of the materials of your
end-of-life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to use those
systems.
If you need more information on the collection, reuse and recycling
systems, please contact your local or regional waste administrator.
You can also contact us for more information on the environmental
performances of our products.

7
Safety Instructions
General Recommendations
Read the safety and operating instructions before operating the
display.
Retain safety and operating instructions for future reference.
Adhere to all warnings on the display and in the operating
instructions manual.
Follow all instructions for operation and use.
Electrical shock
Warning- T o prevent the risk of fire or shock hazards, do not expose
this product to rain or moisture
Warning- Please do not open or disassemble the product as this may
cause electric shock.
Warning- Do not modify this equipment without authorization of the
manufacturer.
Warning- To avoid risk of electric shock, this equipment must only be
connected to a supply mains with protective earth.
Warning- Make sure the user not to contact SIP/SOPs and the patient at
the same time.
Classification:
Electrical Shock Protection: Class I.
Disconnect Device: Connect / Remove power cord plug directly.
Degree of Protection Against Electric Shock: No applied part.
Degree of Protection Against Harmful Ingress of Water: Ordinary
equipment (IPX0).

8
Degree of Safety in the Presence of Flammable Anesthetic Mixture with
Air or with Oxygen or Nitrous Oxide: Not suitable for use in the
presence of a flammable anesthetic mixture with air or with oxygen or
nitrous oxide.
Mode of Operation: Continuous.
Intended use
This display is an AMLCD display designed for viewing medical X-ray
images. This unit should not be used near patients and should be kept
outside of 1.83 m perimeter and 2.29 m vertical.
The unit is not intended to be used in any life support system and
diagnosis.
Power connection
Power requirements: The display must be powered using a medical
approved 12VDC power supply (MDRC-1119, MDRC-1119TS,
MDRC-1119HB) or a 24VDC power supply (MDRC-2120).
The medical approved DC power supply must be powered by the AC
mains voltage.
Power requirements: The display must be powered using a medical
approved 24 VDC SELV power supply.
The medical approved DC power supply must be powered by the AC
mains voltage.
Power cords
Utilize a UL-listed detachable power cord, 3-wire, type SJ or equivalent,
18 AWG min., rated 300 V min., provided with a hospital-grade type
plug 5-15P configuration for 120V application, or 6-15P for 240V
application.

9
Do not overload wall outlets and extension cords as this may result in
fire or electric shock.
Mains lead protection (U.S.: Power cord): Power cords should be routed
so that they are not likely to be walked upon or pinched by items
placed upon or against them, paying particular attention to cords at
plugs and receptacles.
Use a power cord that matches the voltage of the power outlet, which
has been approved and complies with the safety standard of your
particular country.
External equipment
External equipment intended for connection to signal input/output or
other connectors, shall comply with relevant UL/ EN/ IEC standard (e.g.
UL/EN/IEC 60950 for IT equipment and ANSI/AAMI ES60601-1/EN
60601-1 / IEC 60601 series for medical electrical equipment). In
addition, all such combinations – systems – shall comply with the
standard IEC 60601-1-1, Safety requirements for medical electrical
systems. Equipment not complying with ANSI/AAMI ES60601-1/EN /
IEC 60601-1 shall be kept outside the patient environment, as defined
in the standard.
Equipment not complying with IEC 60601 must be kept outside the
patient environment, as defined in the standard as at least 1.5 meters
from the patient or the patient support.
Any person who connects external equipment to signal input, signal
output, or other connectors has formed a system and is therefore
responsible for the system to comply with the requirements of IEC
60601-1-1. If in doubt, speak with a qualified technician.
In locations where 240V outlets are used, connect this display only on a
center-tapped, 240V, single-phase supply.

10
Water and moisture
Never expose the display to rain or moisture.
Never use the display near water - e.g. near a bathtub, washbasin,
swimming pool, kitchen sink, laundry tub or in a wet basement.
Ventilation
Do not cover or block the ventilation openings in the cover of the set.
When installing the display in a cupboard or another closed location,
heed the necessary space between the set and the sides of the
cupboard.
Installation
Place the display on a flat, solid and stable surface that can support the
weight of at least 3 displays. If you use an unstable cart or stand, the
display may fall, causing serious injury to a child or adult, and serious
damage to the equipment.
Recommendations for using your display system
1. Optimize the lifetime of your display
Enabling the Display Power Management System (DPMS) of your
display (in the display’s Settings menu) will optimize its lifetime by
automatically switching off the backlight when the display is not used
for a specified period of time. By default, DPMS is enabled on your
display, but it also needs to be activated on your workstation. To do
this, go to “Power Options Properties” in the “Control Panel”.
Barco recommends setting DPMS activation after 20 minutes of
non-usage.

11
2. Use a screen saver to avoid image retention
Prolonged operation of an LCD with the same content on the same
screen area may result in a form of image retention.
You can avoid or significantly reduce the occurrence of this
phenomenon by using a screen saver. You can activate a screen saver
in the “Display properties” window of your workstation.
Barco recommends setting screen saver activation after 5 minutes of
non-usage. A good screen saver displays moving content.
In case you are working with the same image or an application with
static image elements for several hours continuously (so that the
screen saver is not activated), change the image content regularly to
avoid image retention of the static elements.
3. Understand pixel technology
LCD displays use technology based on pixels. As a normal tolerance in
the manufacturing of the LCD, a limited number of these pixels may
remain either dark or permanently lit, without affecting the
performance of the product. To ensure optimal product quality, Barco
applies strict selection criteria for its LCD panels.
To learn more about LCD technology and missing pixels, consult the
dedicated white paper available at www.barco.com/healthcare.
4. Enhance user comfort
Every Barco multi-head display system is color matched with the
highest specification in the market.
Barco recommends keeping color-matched displays together.
Furthermore, it is important to use all displays of a multi-head
configuration at the same rate to preserve color matching throughout
the economic lifetime of the system.

12
5. Maximize Quality Assurance
The ‘MediCal QAWeb’ system offers online service for high-grade
Quality Assurance, providing maximum confidence and uptime.
Learn more and sign up for the free MediCal QAWeb Essential level at
www.barco.com/healthcare/qa
Unpacking and handling tips
The MDRC display is a precision instrument that requires proper care to
maintain product operation and adherence to specification. Unpack the
display and components carefully, then set up and handle the unit
properly to avoid damage to the LCD panel.
Use both hands to grasp the display case when lifting it from
the shipping carton, but avoid touching the screen.
Do not apply pressure to the screen or touch the screen with
bare fingers or objects. Pressure can affect image quality.
Cosmetics and oils on the skin are both detrimental to the
screen and difficult to remove.
Allow the display to warm up to room temperature before
turning it on. Avoid sudden temperature changes in the
environment, as this may cause condensation, which damages
the display.
Do not set up the display near strong light or heat sources.
Do not block the vents on the back of the display or install the
display in a built-in enclosure. Blocked vents cause excessive
heat to build up inside the display, increasing risk of fire.
When installing components, turn off your computer, but leave
it plugged into a grounded outlet.
Do not remove the back cover or disassemble the display.
There are no user-serviceable parts inside.

13
Preventing fire and injury
Replace the power supply or cables if damaged.
Use only the power source indicated in this guide or listed on
the display.
Do not plug the power supply into an overloaded AC outlet or
extension cord. Overloaded AC outlets and cords can result in
electric shock or fire.
Do not drop or push objects into the display case. Internal
components contain high voltage.
Unplug the power cord from the wall outlet during
thunderstorms.
Do not place magnetic devices, such as motors, near the
display.
Cleaning the display
Observe the following guidelines to maintain display and LCD screen.
Use a clean, lint-free, absorbent cotton cloth to clear off any
residual glue from removal of the protective film or to remove
surface dust. Apply light pressure to remove the dust.
Dampen a clean cloth with a small amount of isopropyl alcohol
to remove glue or dust if the screen is still not clean. Do not
saturate the cloth; otherwise, alcohol may seep into the display
case and collect in the enclosure. Use a clean, dry cloth to
completely remove the alcohol residue.
It is advised to clean the display on weekly basis.
Do not use chemically treated dust cloths, acetone, toluene, or
harsh solvents on the display case or the screen. They can
damage the polarizer and the display case.

14
Do not expose the display to water or excessive moisture. Do
not allow water or other stains to stand on the unit. Wipe
liquids off immediately to prevent damage to the display case
and the screen.
Shipping/storing the display
Keep the display in its shipping container until installation. Return the
display to its original container whenever you need to store the unit,
move it to another location, or return it for repair. The packaging
supplied by the manufacturer protects the display while it is in transit.
See environment specifications for more information.
Before returning the display to the container, do the following:
1 Swivel the display panel in landscape mode.
2 Push the panel down to the lowest position.
3 Use the stand lock to anchor the panel.

15
Explanation of symbols
DISPOSAL. Do not use household or municipal waste
collection services for disposal of electrical and electronic
equipment. EU countries require the use of separate
recycling collection services.
CAUTION. Read the accompanying text carefully for proper
operation and maintenance of the display system.
DIRECT CURRENT
ALTERNATING CURRENT
RELATIVE HUMIDITY
Storage & transport: 5%~ 90% (No condensation)
Operating: 8% ~ 80%
TEMPERATURE
Storage & transport: -20° to 60°
Operating: 0°~35°C
ISO 7000-1641. Follow operating instructions or consult
instructions for use.

16
Introduction
About the product
Thank you for choosing Barco.
The MDRC series are LCD displays with an active matrix, thin-film
transistor (TFT) liquid crystal display (LCD). These products also
demonstrate the following outstanding features:
MDRC-1119 / MDRC-1119 TS / MDRC-1119 HB
Dual Analog and Digital signal.
19” diagonal Screen.
1280x1024 high resolution.
Wide Viewing Angle Technology.
31.5 ~ 80 kHz horizontal scan.
56 ~ 75 Hz refresh rate.
Auto Adjustment and Re-scaling function.
High quality full screen re-scaling capability.
Multilingual OSD user controls.
VESA DPM power saving.
Kensington lock capability

17
MDRC-2120
Dual Analog and Digital signal.
20.1” diagonal Screen.
1600x1200 high resolution.
Wide Viewing Angle Technology.
31.5 ~ 93.75 kHz horizontal scan.
59 ~ 61 Hz refresh rate.
Auto Adjustment and Re-scaling function.
High quality full screen re-scaling capability.
Multilingual OSD user controls.
VESA DPM power saving.
Kensington lock capability

18
Package Overview
USAPowerCord EURPowerCord ChinaPowerCord
PowerAdapter
VGA Signal Cable DVI-D Cable User’s Manual

19
Installation
Product Overview
Front View

20
Back View
MDRC-1119 / MDRC-1119 TS / MDRC-1119 HB
MDRC-2120
DC Power-InUSB Ports
DVI-D Input
VGA Input
DC Power-In
USB Ports DVI-D Input
VGA Input