Barco DP2K-6E User manual

Athena
User Safety & Environmental Information
R5906793/01
26/01/2018

Barco Visual (Beijing) Electronics Co., Ltd
地址：北京市 昌平区 中关村科技园 昌平园 昌盛路 16号
Phone: [phone]
Fax: [phone]
Support: www.barco.com/en/support
Visit us at the web: www.barco.com
Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
Phone: [phone]
Fax: [phone]
Support: www.barco.com/en/support
Visit us at the web: www.barco.com
Printed in Belgium

1. Safety & Environmental Information
1. SAFETY & ENVIRONMENTAL INFORMATION
About this chapter
Read this chapter attentively. It contains important information to prevent personal injury while installing and using your Athena.
Furthermore, it includes several cautions to prevent damage to your Athena. Ensure that you understand and follow all safety
guidelines, safety instructions and warnings mentioned in this chapter before installing and using the Athena. After this chapter,
additional “warnings” and “cautions” are given depending on the procedure. Read and follow these “warnings” and “cautions” as
well.
Clarification of the term “Athena” used in this document
When referring in this document to the term “Athena” means that the content is applicable for following Barco products:
•ATHENA
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guar-
antee. Observing the specification mentioned in this chapter is critical for projector performance. Neglecting
this can result in loss of warranty.
Model certification name
• Athena : DP2K-6E
Overview
• General considerations
• Safety training to be provided by the installer
• Important safety instructions
• Light beam Hazard Distance (HD)
• HD in function of the lens Throw Ratio (TR)
• Disposal information
• China RoHS compliance
• Taiwan RoHS compliance
• Turkey RoHS compliance
• Hazards
• Contact information
• Production address
• Download Product Manual
1.1 General considerations
WARNING:Ensure you understand and follow all the safety guidelines, safety instructions, warnings and
cautions mentioned in this manual.
WARNING:Be aware of suspended loads.
CAUTION:High pressure lamp may explode if improperly handled.
R5906793 ATHENA 26/01/2018 1

1. Safety & Environmental Information
General safety instructions
• Before operating this equipment please read this manual thoroughly and retain it for future reference.
• Installation and preliminary adjustments should be performed by qualified Barco personnel or by authorized Barco service deal-
ers.
• All warnings on the projector and in the documentation manuals should be adhered to.
• All instructions for operating and use of this equipment must be followed precisely.
Notice on safety
This equipment is built in accordance with the requirements of the international safety standards IEC60950-1, EN60950-1,
UL60950-1 and CAN/CSA C22.2 No.60950-1, which are the safety standards of information technology equipment including
electrical business equipment. These safety standards impose important requirements on the use of safety critical components,
materials and insulation, in order to protect the user or operator against risk of electric shock and energy hazard and having access
to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical stability
and strength, enclosure construction and protection against the risk of fire. Simulated single fault condition testing ensures the
safety of the equipment to the user even when the equipment’s normal operation fails.
Owner’s record
The part number and serial number are printed on a label which is stuck on the respective part. Record these numbers in the spaces
provided below. Refer to them whenever you call upon your Barco dealer regarding this product.
Product article number
Product serial number
Dealer
1.2 Safety training to be provided by the installer
WARNING:The installer is responsible that the user is instructed. The user will sign a document to confirm
that the instructions have been received and understood.
Users definition
The Athena is intended for persons who have been instructed and trained by a skilled person (installer or service personnel) to
identify energy sources that may cause injury and to take precautions to avoid unintentional contact with or exposure to those energy
sources.
The skilled person must instruct the user about:
• High intensity light beam. The user must respect the exclusion zone, based on the light beam Hazard Distance (HD).
• Dangerous energy sources inside the projector. The user is not allowed to remove any cover from the projector.
• Small glass parts can leave the projector in the event of lamp explosion. Keep 1 m (40 in.) distance from the air outlet side of
the projector during operation.
• The installation, maintenance or service is for skilled persons only.
• The requirements for a restricted access location and an exclusion zone.
Restricted access location
To protect untrained persons and children, the projector must be installed in a restricted access location. The definition of a
restricted access location is a location for equipment where both of the following paragraphs apply:
• Access can only be gained by skilled persons (installer or service personnel) or persons who have been instructed and trained
by a skilled person. The persons must have been instructed about the reasons for the restriction applied to the location and
about the precautions that shall be taken.
• Access is only possible through the use of the tool or lock and key, or other means of security, and is controlled by the authority
responsible for the location.
Exclusion zone
The projector radiates heat on its external surfaces and from ventilation ducts during normal operation. Exposing flammable or
combustible materials into close proximity of this projector could result in the spontaneous ignition of that material, resulting in a
fire. For this reason, it is absolutely necessary to leave an exclusion zone around all external surfaces of the projector whereby no
flammable or combustible materials are present:
2R5906793 ATHENA 26/01/2018

1. Safety & Environmental Information
• The exclusion zone must not be less than 40 cm (16 in.).
• Loose papers or other objects may not be nearer to the projector than 10 cm (4 in.) on any side.
• Rear exhaust: the exclusion zone on the rear side must not be less than 1 m (40 in.).
To protect untrained users and children against high intensity light beams, the light beam Hazard Distance (HD) shall be taken into
account. See "Light beam Hazard Distance (HD)", page 5 .
1.3 Important safety instructions
To prevent the risk of electrical shock
• Installation according to the local electrical code and regulations by qualified technical personnel only.
• A readily accessible disconnect device must be incorporated externally to the equipment for removal of the power to the pro-
jector cord.
• Warning: High leakage current. Earth connection essential before connecting supply.
• Do not allow anything to rest on the power cord. Do not locate this projector where persons will walk on the cord.
• Do not operate the projector with a damaged cord or if the projector has been dropped or damaged - until it has been examined
and approved for operation by a qualified service technician.
• Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
• If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated
for less amperage than the projector may overheat.
• Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short
circuit parts that could result in a risk of fire or electrical shock.
• Do not expose this projector to rain or moisture.
• Do not immerse or expose this projector in water or other liquids.
• Do not spill liquid of any kind on this projector.
• Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before
resuming operations.
• Do not disassemble this projector, always take it to a trained service person when service or repair work is required.
• Do not use an accessory attachment which is not recommended by the manufacturer.
• Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for
long periods of time, remove all power from the projector. This will prevent damage to the projector due to lightning and AC
power-line surges.
To prevent personal injury
• Caution: High pressure lamp may explode if improperly handled. Refer servicing to qualified service personnel.
• To prevent injury, take note of the weight of the projector. Minimum 4 adult persons are needed to carry the projector.
• To prevent injury, ensure that the lens and all cover plates are correctly installed. See installation procedures.
• Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the eye.
•Warning: extremely high brightness lamps: This projector uses extremely high brightness lamps. Never attempt to look
directly into the lens or at the lamp. If the projection distance is less than 6 meter, any person needs to be at least 4 meters
away from the projected image. Avoid close range reflection of the projected image on any reflecting surface (such as glass,
metal, …) . When operating the projector, we strongly recommend wearing suitable safety glasses.
• Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and
possible injury to the user.
• It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall be changed if they have become
visibly damaged to such an extent that their effectiveness is impaired. For example by cracks or deep scratches.
•Warning: Protection from ultraviolet radiation: Do not look directly in the light beam. The lamp contained in this product is
an intense source of light and heat. One component of the light emitted from this lamp is ultraviolet light. Potential eye and skin
hazards are present when the lamp is energized due to ultraviolet radiation. Avoid unnecessary exposure. Protect yourself and
your employees by making them aware of the hazards and how to protect themselves. Protecting the skin can be accomplished
by wearing tightly woven garments and gloves. Protecting the eyes from UV can be accomplished by wearing safety glasses
that are designed to provide UV protection. In addition to the UV, the visible light from the lamp is intense and should also be
considered when choosing protective eye wear.
•Mercury Vapor Warnings: Keep the following warnings in mind when using the projector. The lamp used in the projector
contains mercury. In case of a lamp rupture, explosion there will be a mercury vapor emission. In order to minimize the potential
risk of inhaling mercury vapors:
- Ensure the projector is installed only in ventilated rooms.
- Replace the lamp module before the end of its operational life.
- Promptly ventilate the room after a lamp rupture, explosion has occurred, evacuate the room (particularly in case of a preg-
nant woman).
- Seek medical attention if unusual health conditions occur after a lamp rupture, explosion, such as headache, fatigue, short-
ness of breath, chest-tightening coughing or nausea.
R5906793 ATHENA 26/01/2018 3

1. Safety & Environmental Information
•Exposure to UV radiation: Some medications are known to make individuals extra sensitive to UV radiation. The American
Conference of Governmental Industrial Hygienists (ACGIH) recommends occupational UV exposure for an-8 hour day to be
less than 0,1 micro-watts per square centimeters of effective UV radiation. An evaluation of the workplace is advised to assure
employees are not exposed to cumulative radiation levels exceeding these government guidelines.
To prevent fire hazard
• Do not place flammable or combustible materials near the projector!
• Projection rooms must be well ventilated or cooled in order to avoid build up of heat. It is necessary to vent hot exhaust air from
console to the outside of the building.
• Heat sensitive materials should not be placed in the path of the exhaust air or on the lamp house.
To prevent projector damage
•Theairfilters of the projector must be cleaned or replaced on a regular basis (a "clean" booth would be monthly-minimum).
Neglecting this could result in disrupting the air flow inside the projector, causing overheating. Overheating may lead to the
projector shutting down during operation.
• The projector must always be installed in a manner which ensures free flow of air into its air inlets.
• In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic Compatibility (EMC)
and safety requirements, it should always be operated with all of it’s covers in place.
• Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product
on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The
device should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
• Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and remove all power
from the projector. Do not operate the projector again until it has been checked by qualified service personnel.
• Do not block the projector cooling fans or free air movement around the projector. Loose papers or other objects may not be
nearer to the projector than 10 cm (4") on any side.
• Do not use this equipment near water.
• Proper operation of the projector can only be guaranteed in table mounting. It is not permitted to use the projector in another
position. See installation procedure for correct installation. A ceiling mount will be supported in the future.
•Special care for Laser Beams: Special care should be used when DLP projectors are used in the same room as high power
laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror DevicesTM in
which case there is a loss of warranty.
• Never place the projector in direct sunlight. Sunlight on the lens can severely damage the Digital Mirror DevicesTM in which
case there is a loss of warranty.
• Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For
maximum protection, repack your set as it was originally packed at the factory.
• To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflective
coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent
solution, or thinner.
• Rated maximum ambient temperature, ta= 35°C (95°F).
On servicing
• Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials
and risk of electric shock.
• Refer all servicing to qualified service personnel.
• Attempts to alter the factory-set internal controls or to change other control settings not specially discussed in this manual can
lead to permanent damage to the projector and cancellation of the warranty.
• Remove all power from the projector and refer servicing to qualified service technicians under the following conditions:
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the equipment.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of the other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to normal operation.
- If the product has been dropped or the cabinet has been damaged.
- If the product exhibits a distinct change in performance, indicating a need for service.
• Replacement parts: When replacement parts are required, be sure the service technician has used original Barco replacement
parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitu-
tions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may
void warranty.
• Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks
to determine that the product is in proper operating condition.
• Possible explosion hazard: Always keep in mind the caution below:
4R5906793 ATHENA 26/01/2018

1. Safety & Environmental Information
WARNING:The user is not permitted to perform or attempt any phase of xenon lamp handling or service.
Only trained and qualified technical service personnel are allowed to handle the xenon lamp.
CAUTION:Xenon compact arc lamps are highly pressurized. When ignited, the normal operating temperature
of the bulb increases the pressure to a level at which the bulb may explode if not handled in strict accordance
to the manufacturer’s instructions. The bulb is stable at room temperature, but may still explode if dropped or
otherwise mishandled. Whenever the lamp house, containing a xenon lamp, has to be dismantled or whenever
the protective container or cloth has to be removed from the xenon lamp, authorized protective clothing MUST
be worn!
To prevent battery explosion
• Danger of explosion if battery is incorrectly installed.
• Replace only with the same or equivalent type recommended by the manufacturer.
• For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rules and regulations
to ensure proper disposal.
Safety Data Sheets for Hazardous Chemicals
For safe handling information on chemical products, consult the Safety Data Sheet (SDS). SDSs are available upon request via
[email protected].
1.4 Light beam Hazard Distance (HD)
HD
Light beam Hazard Distance (HD) is the distance from the source at which the intensity or the energy per surface unit
becomes lower than the applicable safety limit. The light beam can thus be considered as dangerous if the operator
is closer from the source than the HD.
Restriction Zone (RZ) based on the HD
The HD is defined from the projection lens surface towards the position of the lowest projected beam where the irradiance equals
the applicable safety limit. The HD depends on the amount of lumens produced by the projector and the type of lens installed. See
next chapter HD in function of the lens Throw Ratio (TR).
To protect untrained users the installation shall comply with the following installation requirements: light output levels in excess of the
limits shall not be permitted at any point less than 2.0 meters (SH image 1-1) above any surface upon which persons are assumed
to stand or 1 meter (SW image 1-1) below or in lateral separation from any place where such persons are assumed to be. See
image 1-1.
RA
TH
PR
RZ
HD
SW
1m
SW
SW
SW
HD
SH
RA TH
RZ
SH
(B) TOP VIEW(A) SIDE VIEW
Image 1-1
ASideview.
B Top view.
RA Restricted Access location (booth area of projector).
PR Projector.
TH Theater.
RZ Restriction Zone in the theater.
SH Separation Height. Must be minimum 2 meter.
R5906793 ATHENA 26/01/2018 5

1. Safety & Environmental Information
SW Separation Width. Must be minimum 1 meter.
Based on national requirements, no person is allowed to enter the projected beam within the zone between the projection lens and
the related hazard distance (HD). This shall be physically impossible by creating sufficient separation height or by placing barriers.
The minimum separation height takes into account the surface upon which persons are assumed to stand.
On image 1-1 a typical setup is displayed. It must be verified by the installer if these minimum requirements are met. If required a
restricted zone (RZ) in the theater must be established. This can be done by using physical barrier, like a red rope as illustrated in
image 1-2.
PR
Image 1-2
1.5 HD in function of the lens Throw Ratio (TR)
TR (Throw Ratio)
The ratio of the distance to the screen (throw) to the screen width.
6R5906793 ATHENA 26/01/2018

1. Safety & Environmental Information
Hazard Distance
HD [m]
TR
0
0,2
0,4
0,6
0,8
1
1,2
1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6 3,8 4,0 4,2 4,4 4,6
Image 1-3
HD (in meter) in function of the Throw Ratio (TR)
1.6 Disposal information
Disposal Information
Waste Electrical and Electronic Equipment
This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical and
electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste
and recycle them responsibly to promote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local city office or your municipal waste disposal service.
For details, please visit the Barco website at: http://www.barco.com/en/AboutBarco/weee
Disposal of batteries in the product
This product contains batteries covered by the Directive 2006/66/EC which must be collected and disposed of separately
from municipal waste.
If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium (Cd), these chemical symbols will
appear below the crossed-out wheeled bin symbol.
By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential negative effects
on the environment and human health.
Mercury Notice
Hg
LAMP CONTAINS MERCURY,
DISPOSE ACCORDING TO
STATE/LOCAL LAW.
This Barco product consists of materials that may contain mercury, which must be recycled or
disposed of in accordance with local, state, or country laws. See www.lamprecycle.org for disposal information.
R5906793 ATHENA 26/01/2018 7

1. Safety & Environmental Information
For more information on safe handling procedures, the measures to be taken in case of accidental breakage, and safe disposal
options visit: http://www.ec.gc.ca/mercure-mercury.
Within this system, the lamp in the projector contains mercury.
The lamp and the projector are carefully designed to minimize the probability of lamp rupture, although the lamp may break while
operating and small amounts of mercury vapor may be emitted from the projector. As a general precaution, secure good ventilation
in the room when operating the projector. If lamp rupture occurs, evacuate the room and secure good ventilation.
CAUTION:Lamps may not be disposed as normal household trash.
Contact your local waste disposal facility for information on the recycling program for HID (High Intensity
Discharge ) lamps in your area.
Disposal of mercury-containing lamps
• Recycle through a municipal or solid waste district household hazardous waste collection program in accordance with local
regulations.
• Direct shipment to lamp recycler.
• Shipment through a hazardous waste transporter.
WARNING:Do not break or crush lamps because this may pose health and environmental risks when mercury
vapors are released.
CAUTION:To avoid breaking the lamps, repack carefully when storing and transporting them.
WEEE Information
This product conforms to all requirements of the EU Directive on waste electrical and electronic equipment (WEEE). This product
shall be recycled properly. It can be disassembled to facilitate proper recycling of it’s individual parts.
Consult your dealer or relevant public authority regarding drop-off points for collection of WEEE. For details, please visit the Barco
website at: http://www.barco.com/en/aboutBarco/weee.
1.7 China RoHS compliance
中国大陆RoHS (Chinese Mainland RoHS)
根据中国大陆《电器电子产品有害物质限制使用管理办法》（也称为中国大陆RoHS）， 以下部分列出了Barco产品中可能包含的有毒
和/或有害物质的名称和含量。中国大陆RoHS指令包含在中国信息产业部MCV标准：“电子信息产品中有毒物质的限量要求”中。
According to the “Management Methods for the Restriction of the Use of Hazardous Substances in Electrical and Electronic Prod-
ucts” (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances
that Barco’s product may contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information
Industry of China, in the section “Limit Requirements of toxic substances in Electronic Information Products”.
零件项目(名称)
Component Name
有毒有害物质或元素
Hazardous Substances or Elements
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr6+)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
印制电路配件
Printed Circuit Assemblies
XOXOOO
外接电(线)缆
External Cables
XOOOOO
內部线路
Internal wiring
XOOOOO
镜头支架
Lensholder
XOOOOO
8R5906793 ATHENA 26/01/2018

1. Safety & Environmental Information
零件项目(名称)
Component Name
有毒有害物质或元素
Hazardous Substances or Elements
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr6+)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
光学镜头
Optical lenses
XOOOOO
燈泡
Lamp
OXOOOO
螺帽,螺钉(栓),螺旋(钉),垫圈,紧固件
Nuts, bolts, screws, washers, Fasteners
XOOOOO
电源供应器
Power Supply Unit
XOOOOO
风扇
Fan
XOOOOO
本表格依据SJ/T 11364的规定编制
This table is prepared in accordance with the provisions of SJ/T 11364.
O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 GB/T 26572 标准规定的限量要求以下.
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit
requirement in GB/T 26572.
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 标准规定的限量要求.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part
is above the limit requirement in GB/T 26572.
在中国大陆销售的相应电子信息产品（EIP）都必须遵照中国大陆《电子电气产品有害物质限制使用标识要
求》标准贴上环保使用期限（EFUP）标签。Barco产品所采用的EFUP标签（请参阅实例，徽标内部的编号使用
于指定产品）基于中国大陆的《电子信息产品环保使用期限通则》标准。
10 All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with the
“Marking for the restriction of the use of hazardous substances in electrical and electronic product” of
Chinese Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The number
inside the EFUP logo that Barco uses (please refer to the photo) is based on the “General guidelines of
environment-friendly use period of electronic information products” of Chinese Mainland.
1.8 Taiwan RoHS compliance
限用物質含有情況標示聲明書 (Declaration of the Presence Condition of the Restricted Substances
Marking)
設備名稱： 投影儀， 型號（型式）： DP2K-6E
Equipment name: Projector, Type designation: DP2K-6E
限用物質及其化學符號
Restricted substances and its chemical symbols
單元
Unit
鉛
Lead
(Pb)
汞
Mercury
(Hg)
鎘
Cad-
mium
(Cd)
六價鉻
Hexavalent
chromium
(Cr6+)
多溴聯苯
Polybromi-
nated
biphenyls
(PBB)
多溴二苯醚
Polybromi-
nated diphenyl
ethers
(PBDE)
印製電路板配件
Printed Circuit Assemblies
—O—OO O
外接電（線）纜
External Cables
—OO O O O
內部線路
Internal wiring
—OO O O O
R5906793 ATHENA 26/01/2018 9

1. Safety & Environmental Information
設備名稱： 投影儀， 型號（型式）： DP2K-6E
Equipment name: Projector, Type designation: DP2K-6E
限用物質及其化學符號
Restricted substances and its chemical symbols
單元
Unit
鉛
Lead
(Pb)
汞
Mercury
(Hg)
鎘
Cad-
mium
(Cd)
六價鉻
Hexavalent
chromium
(Cr6+)
多溴聯苯
Polybromi-
nated
biphenyls
(PBB)
多溴二苯醚
Polybromi-
nated diphenyl
ethers
(PBDE)
鏡頭支架
Lensholder
—OO O O O
光學鏡頭
Optical lenses
—OO O O O
燈泡
Lamp O—OO O O
螺帽,螺釘（栓）,螺旋（釘）,墊圈,緊固件
Nuts, bolts, screws, washers, Fasteners
—OO O O O
電源供應器
Power Supply Unit
—OO O O O
風扇
Fan
—OO O O O
備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準值。
Note 1：“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance
exceeds the reference percentage value of presence condition.
備考2.〝〇〞係指該項限用物質之百分比含量未超出百分比含量基準值。
Note 2：“〇” indicates that the percentage content of the restricted substance does not exceed the percentage of reference
value of presence.
備考3.〝—〞係指該項限用物質為排除項目。
Note 3：The “—” indicates that the restricted substance corresponds to the exemption.
1.9 Turkey RoHS compliance
Turkey RoHS compliance
Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur.
[Republic of Turkey: In conformity with the WEEE Regulation]
1.10 Hazards
Safety notice Sodium Carbonate (Na2CO3)
According to the Material Safety Data Sheet (MSDS), Sodium Carbonate could cause the following hazards:
• Potential Acute Health Effects: Hazardous in case of skin contact (irritant), of eye contact (irritant), of ingestion, of inhalation
(lung irritant).
• Potential Chronic Health Effects: Slightly hazardous in case of skin contact (sensitizer). The substance may be toxic to upper
respiratory tract, skin, eyes. Repeated or prolonged exposure to the substance can produce target organ damage.
10 R5906793 ATHENA 26/01/2018

1. Safety & Environmental Information
1.11 Contact information
Barco contact information
Registered office address: President Kennedypark 35, 8500 Kortrijk, Belgium
Contact address: Beneluxpark 21, 8500 Kortrijk, Belgium
Importers contact information
To find your local importer, contact Barco directly or one of Barco’s regional offices via the contact information given on Barco’s web
site, www.barco.com.
1.12 Production address
Factories
Barco NV (BELGIUM)
President Kennedypark 35, B-8500 Kortrijk
CFG Barco (Beijing) Electronics Co. Ltd.
中影巴可（北京）电子有限公司
3rd Floor, Barco Factory, No.16 Changsheng Road, Changping District, 102200, Beijing, P.R.C.
北京市昌平区中关村科技园区昌平园昌盛路16号巴可工厂第3层邮政编码：102200
Barco Visual (Beijing) Electronics Co. Ltd.
巴可伟视（北京）电子有限公司
No.16 Changsheng Road, Changping District, 102200, Beijing, P.R.C
北京市昌平区中关村科技园区昌平园昌盛路16号邮政编码：102200
Made in information
The made in country is indicated on the product ID label on the product itself.
Production date
The month and year of production is indicated on the product ID label on the product itself.
1.13 Download Product Manual
Download Product Manual
Product manuals and documentation are available online at www.barco.com/td.
Registration may be required; follow the instructions given on the website.
IMPORTANT! Read Installation Instructions before connecting equipment to the mains power supply.
R5906793 ATHENA 26/01/2018 11