Barker 27265 User manual

(+)
30
AMP
HIGH-POWER 3,000 ACME JACK OWNER'S INSTRUCTIONS
P/N’S 27265, 27295, 27300, 27720, 27721, 28762
GENERAL SAFETY:
Read and understand the Jack installation instructions. Always block trailer wheel when using the jack. Since there are moving parts inside the jack, be careful of loose clothing,
remove or secure loose jewelry (watches, rings, etc.).
30 amp slow blow fuse
VIP Jack travel trailer
battery
Connect the lead-wire directly to the positive (+) lead of
the travel trailer's battery using a twelve (12) gage wire.
Be sure the connection is a good one. THE 30 AMP
SLO-BLO FUSE MUST BE INSTALLED AS SHOWN.
INSTALLATION:
IMPORTANT NOTICE:
If it is necessary to change the position of the powerhead relative to the post and flange (in order to provide clearance between powerhead and LP gas bottle
or LP gas cover, or more clearance between the lift gate and the powerhead) loosen set screws and rotate head without lifting off coupling. Retighten
set screws when head is in desired position.
BEFORE INSTALLATION:
Raise your travel trailer's front end and place blocks or stabalizing jacks
under the front "A" frame. Lower the trailer until it rests securely on
stabilizing jacks or blocks. Retract present jack and remove.
H&H Engineering HIGH POWER Acme Jack is designed to lift up to 3,000 pounds a full 18". It's design also includes a silent shut-off by use of limit switches; a built in leveling devise;
attached foot plate and an emergency crank handle. An important part of owning and using a HIGH-POWER Jack is being sure it is properly installed and serviced.
Remove present
jack
"A" frame coupler
IMPORTANT
To insure a good
electrical ground an
internal tooth lock-
washer must be in
place for this bolt.
Make sure powdercoat
or paint is removed from
"A" frame coupler under
washer and that tagged
hole is used.
The bolts should
already be on
your trailer.
Install Jack in hole and secure with 3 bolts & 3 internal tooth lockwashers (bolt holes are threaded). The 3 bolts should already be
on your trailer. The 3 internal lockwashers are supplied by us (in hardware bag). Attach the foot plate to High-Power Jack with
.50-20 bolt and .50" lockwasher (supplied in hardware bag).
VIP
SERIES
3000
30 0 0 0 L B S C A P A C I T Y
INITIAL SET-UP AND HOW TO USE YOUR HIGH-POWER JACK LEVEL:
1. Install your High-Power Jack (SEE INSTALLATION above).
2. Place a small level inside your RV on a surface you want to level. This might be a counter top or freezer compartment of a refrigerator.
NOTE: It will be necessary to move this level to check side to side and front to back condition.
3. Check the "inside level", level your trailer from side to side with stabilizing jacks or boards under the wheels.
4. Checking the "inside level", level your trailer front to back using your VIP Power Jack.
5. Carefully adjust the 3 stainless steel screws on the ring that surround the built in bulls-eye level (see picture) until the air bubble is inside the middle
circle. Your trailer will then be leveled. In the future, you can do all your
leveling by using your High-Power
Jack built-in level.
Bulls-eye Level
Retaining Ring
Stainless Steel Screws
B A R K E R M F G . B A T T L E C R E E K
POWER
SERIES
3000
High
3 0 0 0 0 L B S C A P A C I T Y
Sticker indicates
the “lock position”
of the level assembly.
MAINTENANCE:
Once a year, the powerhead should be removed and a liberal amount
of grease (preferably a grease with high melting point) applied directly
to the coupling on which the drive pin rests.
DO NOT POUR OIL into top of the jack post.
Once a year, the housing cover should be removed and the gears
inspected for proper lubrication.
Remove 4 screws and tap around edge of housing to free cover.
DO NOT insert screw driver blade! (This may damage mating
surfaces.)
Before replacing cover, clean matging surfaces.
If lubrication is needed, use Mobilith 460 grease or equivalent.

OPERATION (ELECTRIC)
REMEMBER TO KEEP HANDS AND FEET FROM UNDER
THE FOOT PLATE WHEN USING POWER JACK.
When VIP Jack reaches the end of it's travel (either
raising or lowering), the internal clutch activates.
Dolly wheels are not recommended.
Warning
AVOID THE RISK OF INJURY OR DEATH TO YOURSELF AND OTHERS:
USE THE JACK FOR LIFTING THE TRAVEL TRAILER ONLY.
.NEVER GET BENEATH THE TRAILER WHEN IT IS SUPPORTED BY THE JACK.
.SUPPORT THE VEHICLE WITH THE APPROPRIATE MEANS.
.
OPERATION (MANUALLY):
WARNING!!!
Do not use toggle switch with
crank handle in place.
Breaking this rule will cause
serious injury or death.
REMEMBER TO KEEP HANDS AND FEET OUT FROM UNDER
THE FOOT PLATE WHEN USING THE POWER JACK!!
DOLLY WHEELS ARE NOT RECOMMENDED.
BREAKING THESE RULES WILL CAUSE SERIOUS INJURY OR
DEATH.
WARNING
19989
Don't risk serious injury or
death in a shearing or
squeezing accident. Keep
body, hands, and feet away.
If an electrical failure should occur,
the emergency handle may be in-
serted into the jack post and the
jack can be raised or lowered.
(Access can be obtained by twist-
ing cap off. NOTE: You do not
have to remove or loosen
screws on level to remove the
level assembly.) If the power-
head is removed, crank can
still be used to raise and
lower jack.
..
The JACK will raise and
lower by this
toggle switch--
NOT the travel trailer.
The "night-light" is
controlled by this
toggle switch
UP
DOWN
BARKERMANUFACTURING
P/NXXXXX
Performance
SERIES
3000
High
SCHEMATIC WIRING DIAGRAM
P/N 736-2300
STRAPATTACHMENT:
1. Press strap (1) onto the stud (2) at
the bottom of the cap.
2. Press the retaining ring (3) on stud
(2) snug it down against the strap (1).
3. Repeat this process (4) on the stud
found on the inside of the cover.
THIS WILL SECURE YOUR CAP.
2
314
COVER,
INSIDE
BOTTOM OF CAP
BARKER MFG. BATTLE CREEK
HIGH POWER
SERIES
3000
30000LBS CAPACITY
HIGH-POWER 3,000 ACME JACK OWNER'S INSTRUCTIONS
P/N’S 27265, 27295, 27300, 27720, 27721, 28762 HIGH-POWER 3,000 ACME JACK OWNER'S INSTRUCTIONS

PARTS: ITEM PART# REQ'D DESCRIPTION
1 28259 1 CRANK HANDLE
2 600-0011 1 HEX BOLT (.5-20 X .75)
3 30330 1 CAP ASS'Y BLACK
3 30331 1 CAP ASS'Y WHITE
4 736-0009 1 TOGGLE SWITCH
5 736-0008 1 TOGGLE SWITCH
6 606-5001 2 #10 X .50 PHILLIPS HEAD SCREW
7 27253 1 LAMPWIRE ASSEMBLY
8 10017 1 POST ADAPTER (2" POST ONLY)
9 32152 1 COVER, FINISHEDWHITE
9 32153 1 COVER, FINISHED BLACK
10 29306 1 GASKET
11 28207 1 GEAR ASSEMBLY-DRIVE
12 28917 1 DRIVE GEAR ASSEMBLY
13 30783 1 BASE FINISHEDWHITE
13 30782 1 BASE FINISHED BLACK
14 608-0006 3 .312-18 X .50" SET SCREW
15A 27313 1 POST ASSEMBLY(BLACK- Ø2.25)
15B 27335 1 POST ASSEMBLY(BLACK- Ø2)
15A 27527 1 POST ASSEMBLY(WHITE-Ø2.25)
16 619-0003 3 INTERNALTOOTH LOCKWASHER
17 21349 1 BASE H.T. (BLACK)
17 12752 1 BASE H.T. (WHITE)
18 27262 1 LENS
19 27276 1 MOTOR SLEEVE (BLACK)
19 27344 1 MOTOR SLEEVE (WHITE)
20 26236 1 RUBBER GROMMET
21 17414 1 MOTOR
22 611-2100 2 HEX LOCK NUT
23 605-0012 4 SCREW
24 12393 1 SYNCHRONIZE LABEL
25 27338 1 COVER (WHITE)
25 27259 1 COVER (BLACK)
26 80208 1 WASHER, SPACER
27 29880 1 CONNECTOR/FUSE HOLDER ASSEMBLY
28 623-1216 1 GROOVE PIN
29 606-0009 2 #10 X .38 SCREW (LIMIT SWITCH)
30 636-0000 1 HEX KEY
31 618-1002 1 LOCKWASHER (.50")
32 30341 1 LOCK INDICATOR LABEL, BLACK
32 30683 1 LOCK INDICATOR LABEL,WHITE
33 80501 2 BUSHING
34 645-0024 1 FLANGE BUSHING
35 641-0009 1 BUSHING
36 634-0028 2 RETAINING RING
37 16434 2 HOLE PLUG
38 621-0004 2 Ø.13" X .75 DOWEL
39 634-0023 1 RETAINER RING
40 27512 1 LIMIT SWITCH ASSEMBLY
41 27257 1 BLACKWIRE ASSEMBLY
42 27256 1 WHITEWIRE ASSEMBLY
43 27254 1 BLUE WIRE ASSEMBLY
44 27252 1 GREENWIRE ASSEMBLY
45 606-0008 2 #10-16 X .75TEK SCREW (BLACK)
45 606-0010 2 #10-16 X .75TEK SCREW (SILVER)
46 30313 1 LENS GASKET
47 27277 1 POT/REED DRIVE GEAR
48 27264 1 COVER LABEL
49 27274 1 MOTOR SEAL
50 603-5016 2 #10-32 X .75" PHILLIPS SCREW
51 17808 1 WIRE CLAMP
52 24047 1 WARNING LABEL
53 17892 2 CABLETIE (GREY)
53 16392 2 CABLETIE (BLACK)
2
45
6
9
10
11 12
13
14
15A 15B
52 52
24 24
16
17
31
50
19
21
49
30
28
38
27 22
35
33
26
23
29
47
39
40
20 41
7
43
44
18 46
36
25
45
NOT SHOWN: PN 742-0051 FEMALETERMINAL 1 REQ'D
37
34
51 38
32 3
8
1
53
HIGH-POWER 3,000 ACME JACK OWNER'S INSTRUCTIONS
P/N’S: 27265, 27295, 27300, 27720, 27721, 28762
48
OFF
LIGHT ON
BARKER MFG. BATTLE CREEK
Performance
SERIES
3000
High
30000LBS CAPACITY