Bushranger RJX01 User manual

| X JACK Guidelines
Page 1
PLEASE READ THESE GUIDELINES CAREFULLY BEFORE USING PRODUCT. FAILURE TO DO SO MAY RESULT IN SERIOUS
INJURY, DAMAGE TO PARTS AND/OR EQUIPMENT AND VOID YOUR WARRANTY.
Component List
Specications
Qty
1. X JACK
2. Heavy Duty Storage Bag
3. Hose A
4. Hose B
5. Protective Mat
6. Instructions
7. Replacement Seal Kit
8. Protective Gloves
9. Compressor Adapter
Material:
Inated Height:
Inated Diameter:
Maximum Capacity:
Total Kit Weight:
Reinforced PVC
750 mm
650 mm
2000 kg
8.6kg (X JACK only 5.4 kg)
1
1
1
1
1
1
1
1 Pair
1
X JACK must be inated and deated several times immediately after purchase. Please follow all the guidelines and
warnings before proceeding.
General Warnings
Important Notice
• It is highly recommended that prior to using this X JACK that users undertake off road training course including vehicle
recovery. Recovering immobilised vehicles is potentially a dangerous exercise and this X JACK is to be used with
great care.
• Ensure these guidelines have been read and understood prior to use.
• This X JACK is not suitable for all vehicle recovery circumstances.
• These are guidelines only and do not cover all situations, if in any doubt seek professional assistance.
• The equipment in the X JACK kit shall not be used for any purpose other than as described in these guidelines.
• Any trailer or caravan attached to vehicle shall be disconnected prior to operating X JACK.
X JACK will not inate vehicles with an acute angle exhaust. Vehicles with acute angle exhaust, for example: Toyota
Landcruiser 100 Series, Toyota Landcruiser 80 Series, and the Nissan Patrol GU. Please use the X JACK compressor feature
to inate or alternatively an ancillary extension pipe is available free of charge* by contacting customer service on
1800 654 767. This allows the rubber cone on the hose of the X JACK to t snug.
Dual exhaust vehicles will need to use the X JACK compressor feature to inate. *Australia only.
X JACK
RJX01
7
6
2
8
4
3
1
9
5

| X JACK Guidelines
Page 2
X JACK Warnings
•Never allow any part of your body to be under the vehicle when it is supported by the X JACK.
•Never use X JACK for vehicle maintenance, accessory tment or wheel removal.
• Ensure immobile vehicle is stable and not in a position where a rollover could occur prior to getting out of the vehicle or
commencing vehicle recovery.
•Chock wheels which will remain on the ground when the X JACK is inated to prevent the vehicle from rolling.
Use X JACK to lift vehicle, do NOT use the X JACK as a vehicle support.
• Never get underneath a vehicle during recovery operations.
• Never inate X JACK beyond 68.9 kPa (10psi). Do not over inate. Once the X JACK has fully inated or stopped lifting
the vehicle, stop operation. The X JACK will not lift the vehicle any higher. Any attempt to inate the X JACK further could
damage the X JACK and result in product failure.
• Check that the X JACK is safe to use as per “Safety & Care Information” of the guidelines.
• No person(s) are to remain in a vehicle that is being raised. All person(s) except for the X JACK operator are to be well
clear of the vehicle.
• Never lift the vehicle from the front or rear end where the front two wheels or rear two wheels are lifted off the ground
simultaneously. Recommended recovery locations are on one side of the vehicle between the front and rear wheels – See
step 3 in X JACK Guidelines.
• Never attempt to push the vehicle during a vehicle recovery.
• Be aware that vehicles exhaust fumes are poisonous if inhaled in large quantities. Therefore do not use X JACK in a
conned area and always turn off engine when not inating the jack.
• If using air compressor to inate X JACK, never leave unattended.
X JACK Guidelines
Apply handbrake and chock three remaining wheels to stop vehicle from moving.
Using a shovel, ensure all four wheels of the immobilised vehicle have a clear path
in the direction that the vehicle will travel during recovery.
STEP 1: Secure Vehicle from Rolling
STEP 2: Prepare X JACK
STEP 3: Position X JACK Under Vehicle
Compress X JACK with the top and base on top of each other (similar to a crushed drink can).
Connect the hose A to the X JACK inlet by turning in a clockwise direction and tighten.
Assemble hose B to hose A, with the compressor adapter between them and lay
out at to remove any kinks. Use protective mat between the vehicle and the
X JACK to help prevent punctures.
Select a strong underbody location capable of supporting weight of vehicle. Never locate under fuel tanks, fragile plastic
body parts or exhaust system. Avoid sharp body protrusions, brackets, bolts or edges. See gure 2 for recommended
recovery locations.
Where possible use X JACK on level ground.
Note: Make sure the sealing ring is free of sand or dirt.
Note: You can use your cab oor mats to give you extra bag protection if required.
Note: Where possible position X JACK so it lifts no more than one wheel off the ground
Front
Rear
Figure 1
Compressor Adapter
Figure 1
Figure 2

| X JACK Guidelines
Page 3
STEP 4: Lifting Operation (No Person(s) Shall Remain in Vehicle)
STEP 5: Lowering Operation
STEP 6: Inspection
Safety & Care Information
Safety & Inspection
Care & Maintenance
Make sure vehicle’s gearbox is in neutral or park and start vehicle’s engine and allow to idle.
OPTION A - Air Compressor: Inate XJack by connecting an air line to the compressor adapter inlet – Do NOT leave unattended.
OPTION B - Vehicle Exhaust: Firmly press rubber cone end of hose over vehicle’s exhaust pipe end, making sure the hose has no
kinks.
When X JACK is partially inated (just touching vehicle) turn off air compressor/engine and ensure the X JACK is squarely in
position and clear of sharp edges and hot areas. Check to see if protective mats are correctly positioned –
See Note 1 below.
Restart air compressor/engine and continue to inate X JACK until wheel is clear off the ground, then turn off air
compressor/engine. Do NOT inate beyond required height or exceed 68.9 kPa (10psi) – X JACK does NOT need to be fully
inated for recovery.
It is important to lower the vehicle by slowly turning the hose anti-clockwise to deate X JACK. Ensure not to deate too
quickly or it will cause a rapid deation of the X JACK resulting in an uncontrolled lowering of the vehicle.
Note 1: If X JACK does not achieve an upright position or is not positioned correctly during ination process, stop operation.
Deate X JACK – see Step 5 Lowering Operation then repeat Step 4 after realigning X JACK.
Note 2: If the X JACK does not inate, check the exhaust system for leaks.
Note 3: Do NOT over inate. If X JACK reaches full ination (i.e. 10psi) or stoped lifting the vehicle, STOP operation.
Note: DO NOT get under a raised vehicle.
Note: Ensure all body parts are kept clear of vehicle whilst deating.
If the X JACK exhibits any of the above discard the X JACK.
After recovery, ensure vehicle is stationary and secure. Remove recovery equipment.
Inspect X JACK for damage before packing. If damage noted, please do not use. Contact our ofce on the number stated
below for further advice.
• Ensure X JACK is not stored in direct sunlight or wet / humid environments.
• Do not expose X JACK to any petroleum-based products, acids or alkaline products
• Clean X JACK in warm water and allow to dry in the shade. (Always ensure X JACK is dry prior to being stored).
• Always inate and deate the X JACK several times after purchase to prolong the life of the X JACK.
• Always inate and deate the X JACK several times at 3 months intervals when it has not been inated. Inating and
deating the X JACK regularly not only prolongs the life of the X JACK, it also allows you to familiarise yourself with the
X JACK and its functions.
• Evidence of heavy impacts
• Cuts and abrasions
• Badly worn
• Seam weld damage
• Deformation
Prior to using the X JACK or any of its components inspect for damage. Damage may include:
Please follow all points - Failure to do so will void the warranty.

| X JACK Guidelines
Page 4
Kingsley Products - Warranty Policy
Term Meaning
Product
information
information about the Kingsley product which may be contained in any of the documentation provided with
the Kingsley product, including safety instructions, installation instructions, operating instructions, owner’s manual,
service manual, labels and packaging
Purchase date the date you purchased the Kingsley product from a Kingsley outlet, as specied in the purchase receipt
Kingsley outlet an outlet authorised by Kingsley to sell Kingsley products
Kingsley products products or components which Kingsley manufacturers or sells through Kingsley outlets
Warranty period commences on and from the purchase date and ends as follows:
Exhaust X JACK - 12 months warranty
We/Us
Kingsley Enterprises Pty Ltd (ABN 23 001 592 749)
E: [email protected]
A: 6A Brooks Road, Ingleburn NSW 2565
P: 1800 654 767
W: www.kingsleyenterprises.com.au
You the purchaser of the Kingsley product from a Kingsley outlet
1. Our Warranty
We warrant to you that the Kingsley product is free from defects in workmanship and materials for the
warranty period.
2. Fitting and use
Please ensure you:
a. t the Kingsley product in accordance with the product information and all relevant vehicle safety and
compliance laws
b. use the Kingsley product for the purpose for which it was originally designed and in accordance with
the product information and all relevant vehicle safety and compliance laws
3. Exclusions
Our warranty doesn’t cover:
a. normal wear and tear
b. tting the Kingsley product other than in accordance with the product information and any relevant
vehicle safety and compliance laws, including incorrect tting
c. using the Kingsley product other than for the purpose for which it was originally designed or other
than in accordance with the product information and any relevant vehicle safety and compliance
laws, including unusual, improper or negligent use or misuse or overloading
d. misuse or neglect of the Kingsley product, including improper repair or maintenance or failing to repair
or maintain
e. alteration, abuse, acts of nature, terrorism, vandalism, collision, road hazards or adverse conditions
4. Making a claim
Please immediately contact us as soon as you become aware of a possible defect in the Kingsley product.
We’ll arrange for you to either attend a Kingsley outlet (at your cost) for a Kingsley representative to inspect
the Kingsley product (as tted to your vehicle) or for you to return the Kingsley product to us. We’ll also
request you to provide the purchase receipt and complete a warranty claim form. In order to ensure our
warranty is not voided, please keep the purchase receipt as proof of purchase and don’t remove the tted
Kingsley product from your vehicle before contacting us. Note: Non-transferable warranty. The original
purchaser can only claim warranty. If your claim’s in order, we’ll notify you and (at our sole discretion) either
repair or replace the defective workmanship or materials (at our cost) or refund to you the purchase price you
paid for the defective Kingsley product. If further information or investigation is required or if the claim does
not meet the requirements under our warranty, we’ll let you know.
5. Australian Consumer Law
The Kingsley product comes with guarantees that can’t be excluded under the Australian Customer
Law. You’re entitled to a replacement or refund if there’s a major failure and compensation for any other
reasonably foreseeable loss or damage. You’re also entitled to have the Kingsley product repaired or
replaced if it fails to be of acceptable quality and the failure doesn’t amount to a major failure.
6. Other consumer rights
The benets to you under our warranty are in addition to any other rights and remedies you are entitled to
under relevant consumer laws. Our warranty replaces any other warranty given by Kingsley or it’s supplier in
respect of the Kingsley product.
7. Terms
The following terms have the following meanings: