BARRON EXITRONIX LL30 Series User manual

LL30 SERIES
INSTALLATION INSTRUCTIONS
SAVE THESE INSTRUCTIONS!
READ CAREFULLY AND FOLLOW ALL INSTRUCTIONS FOR YOUR OWN SAFETY
• DISCONNECT AC POWER SUPPLY BEFORE SERVICING.
•Installation and servicing of this equipment should be performed by qualified service personnel only.
•Ensure the electricity connections conform to the National Electrical Code and local regulations if applicable.
•Do not mount near gas or electrical heaters.
•Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by
unauthorized personnel.
•The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
Any modification or use of non-original components will void the warranty and product liability.
•Do not use this equipment for other than intended use.
800.533.3948 •www.barronltg.com
10070057 Rev 4 - 02/14
INSTALLATION INSTRUCTIONS
1. Mount steel bracket (5) to junction box, using hardware provide with junction box.
2. All Electrical connection should be made inside junction box.
Make Electrical Connection as follows:
120V AC 277V AC
White - Common White - Common
Black - 120V Orange - 277V
Green - Ground Green - Ground
Note: Cap unused leads to prevent shorting.
3. Mount Emergency light unit to the steel bracket (5).
4. Remove lamp cover (1) by removing the cover hold plug (6).
5. Remove cover housing (2) by loosening four cover housing screws (7).
6. For additional mounting support knockout key hole and use appropriate hardware for mounting surface.
7. Use supplied wire nuts to connect lamp leads with lamp power leads (Purple and Yellow).
8. Make appropriate battery lead connection:
• Red lead to positive (+) terminal.
• Blue lead to negative (-) terminal.
9. Reinstall cover housing (2) carefully to avoid damaging LED AC ON indicator, retightening for screws (7)
10. Reinstall lamp cover (1) by replacing the cover hold plug (6).
11. Turn on power supply.
1

SELF-DIAGNOSTICS TESTING:
1. NORMAL OPERATION
When unit is functioning properly with A.C. power supplied, the status indicator will be green.
2. TESTING
The exit performs two types of test, Contingency and Non-Contingency.
The contingency testing includes “Battery Disconnected Mode” and “Lamp Failure Mode”. When the Battery is
disconnected, the indicator would indicate as Red (Steady). When the Lamp fails, the indicator would indicate as Red
(Blinking - three times). The Non-Contingency test is for testing the Battery for its “discharging” and “recharging”
capacity. A 1minute battery discharge test is performed every 30 days to check for the normal operation of the battery
and the unit. Also a full 90 minute discharge this is performed once a year to confirm the same. When the battery is in
discharging mode, the LED indicator would be a flashing Green (Three/Four Pulses). Upon completion of the test and
after 24 hours battery charging (Indicator on Red and Green flashing), the status indicator will return to either Green
(Steady) indicating a properly functioning unit or Red (Double Pulse) to show a battery failure. The following table
shows the status indication.
MANUAL TESTING:
Battery and Lamp test may be manually
initiated by pressing the manual test switch.
Once the test switch is pressed, the unit
would be reset and the date of battery
self-testing would start counting again.
OPERATION:
During and electrical power failure, the
lamps will automatically come on for a
minimum of 90 minutes. To test this unit, the
battery needs to be charged initially for 2
hours before depressing the test switch.
On pressing the test switch, the emergency
lamps will illuminate. When the switch is
released, the lamps will turn off.
LL30 SERIES
INSTALLATION INSTRUCTIONS
800.533.3948 •www.barronltg.com
10070057 Rev 4 - 02/14
CAUTION This equipment is furnished with a low voltage
disconnect circuit to protect the battery from fully
discharging after its useful output has been used. Allow 24
hours recharge time after installation or power failure for
full load testing.
1. Lamp Cover
2. Cover Housing
3. Lamp
4. Base Housing
5. Mounting Bracket
6. Cover Hold Plug
7. Cover Housing Screw
8. Setting Screw
9. Battery
10. Circuit Board
11. Wire Nuts
12. Purple & Yellow
67
8
9
11
10
5
4
12
3
2
1
ACTION
REACTION AND LED INDICATION
Press test button once (Within 2 seconds) 30-second test: Green light – Single blinking
Press test button 2 times (Within 2 seconds)
15-minute test: Green light – Double blinking
Press test button 3 times (Within 2 seconds)
90-minute test: Green light – Triple blinking
FUNCTION
LED INDICATION
Exit is in Emergency Mode
Off
Exit is in Normal Mode
Green (Steady)
Battery Disconnected
Red (Steady)
Lamp Failure Red (Flashing 4 times)
Battery Fast Charging
Red and Green (Flashing Alternately)
Battery Failure*
Red (Flashing 2 times)
30 Second Battery Discharging Mode
Green (Flashing 1 time)
15 Minute Battery Discharging Mode**
Green (Flashing 2 times)
90 Minute Battery Discharging Mode***
Green (Flashing 3 times)
* = Happens only after battery discharges once in every 30 days or 1 year.
** = Occurs once in every 30 days.
*** = Occurs once in a year.
2