Baumatic CAN52.3ME User manual

CAN52.3ME
CAN75.3SS
Canopy hood

User Manual for your Baumatic
CAN52.3ME 52 cm
CAN75.3SS 75 cm
Canopy Hood
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
GS 03/05/11
2

3
Contents Page
Environmentalnote 4
IMPORTANT SAFETY INFORMATION 5 – 7
Specifications of your cooker hood 8 – 10
CAN52.3ME 8
CAN75.3SS 9
Using your Baumatic cooker hood 10 - 11
Beforefirstuse 10
To use your cooker hood 10 - 11
Cleaning your Baumatic cooker hood 11 – 12
Generalcleaning 11
The grease filter 12
Maintenance 12 – 15
Removing and cleaning the grease filter 12 - 13
Changingalightbulb 13-14
Fitting the carbon filters 14 - 15
Installation 16 - 21
Electrical connection 16 - 17
Before beginning installation 17 - 18
Installing your cooker hood 18 - 19
Connecting to external ducting 20
Completing the installation 20 - 21
Extraction mode or recirculation mode? 21 - 22
Troubleshooting 22 - 23
Contactdetails 24

ENVIRONMENTAL NOTE
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any
plug useless. Cut the cable off directly behind the appliance to
prevent misuse. This should be undertaken by a competent
person.
oThe packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
oPlease discard all packaging material with due regard for the
environment.
4

IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If
you are unsure of any of the information contained in
this booklet, please contact the Baumatic Advice Line.
IMPORTANT: Any installation work must be
carried out by a qualified electrician or
competent person.
oThe hood must be installed in accordance with the installation
instructions and all measurements followed.
oIf the cooker hood is installed for use above a gas appliance then
the provision for ventilation must be in accordance with the Gas
Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural
Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation &
Use) Regulations, the Building Regulations issued by the
Department of the Environment, the Building Standards
(Scotland) (Consolidated) Regulations issued by the Scottish
Development Department.
oIt is dangerous to alter the specifications or to modify this
product. Do not tamper with it or attempt to modify the
appliance in any way.
oWhen installing the hood, ensure that the following
recommended distances are observed between the highest point
on the hob top (including the burners) and the bottom of the
cooker hood:
¾Electric cookers: 700 mm
¾Gas cookers: 700 mm
¾Coal/ oil cookers: 800 mm
IMPORTANT: DO NOT SET YOUR COOKER HOOD LESS
THAN 700mm ABOVE YOUR COOKER.
oWhen installed between adjoining wall cabinets, the cabinets
must not overhang the hob.
5

oThe edges of the cooker hood are sharp – be mindful of this as
you handle your appliance, especially during installation and
cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS!
oIf the room where the cooker hood is to be used contains a fuel
burning appliance such as a central heating boiler then its flue
must be of the sealed or balanced flue type.
oIf other types of flue or appliances are fitted, ensure that there is
an adequate supply of air in the room.
oWhen the hood is being used in its extractor function, ensure
that the ducting is fire retardant and that there are no bends
sharper than 90 degrees as this will reduce the efficiency of the
hood.
oEnsure the ducting for the extractor function has the same
diameter as the outlet hole all the way through.
oKeep young children from using, playing with
or tampering with the cooker hood. Older
children and infirm persons should be
supervised if they are using the cooker hood.
oYour cooker hood is for domestic use only.
oPlease dispose of the packing material carefully – children are
especially vulnerable to it.
oDirty oil is an even greater fire risk.
oAlways put lids on pots and pans when cooking
on a gas cooker.
oThe manufacturer refuses to accept any responsibility for
damages arising to the hood or it catching on fire, from a failure
to observe the fire safety advice contained in this instruction
booklet.
6

oRemember that when in extraction mode, your cooker hood is
removing air from your room. Ensure that proper ventilation
measures are being observed.
oNote that it removes odours from your room, not steam.
oWarning - Always ensure that the cooker
hood has been disconnected from the
power supply before carrying out any work
on the hood, including replacing light bulbs.
oDo not connect the ducting system of this appliance to any
existing ventilation system which is being used for any other
purpose.
oDo not install above a cooker with a high level grill.
oNever leave frying pans unattended during use
as overheated fats and oils might catch fire.
oThe cooker hood should not be exposed to a direct heat source
from the cooking device underneath it, i.e. naked flame from a
gas burner or heat from electric hob zones without a pan on
them.
oDo not attempt to use the cooker hood if it is damaged in any
way. Never attempt to use it without the grease filters fitted or
if the filters are excessively greasy!
oNever flambé cook under this cooker hood.
oThe lights on this appliance should only be used during operation
of the cooker hood. They should not be left on permanently and
used as a lighting source.
THE MANUFACTURER DECLINES ALL
RESPONSIBILITY IN THE EVENT OF FAILURE TO
OBSERVE THE INSTRUCTIONS GIVEN HERE, FOR
INSTALLATION, MAINTENANCE AND SUITABLE
USE OF THE HOOD.
7

Specifications of your cooker hood
CAN52.3ME
Product dimensions
Height: 166 mm
Width: 520 mm
Depth: 321 mm
Your canopy hood is fitted with:
oSlider control operation
oIntegrated axial motor
o3 speeds
o1 washable aluminium grease filter
oNo-return airflow flap
o2 halogen lights
oNoise level: 45 / 50 / 55 dB
Extraction capacity: 250 m³ / hr
Recirculation capacity: 147 m³ / hr
Optional extras: 1 pair ST1 carbon filters for air recirculation
mode
DK5 1 metre length ducting kit 125 mm Ø
DK10 3 metre length ducting kit 125 mm Ø
with flat channelling included.
8

CAN75.3SS
Product dimensions
Height: 245 mm
Width: 746 mm
Depth: 296 mm
Your stainless steel canopy hood is fitted with:
oSlider control operation
oIntegrated axial motor
o3 speeds
o1 washable aluminium grease filter
oNo-return airflow flap
o2 halogen lights
oNoise level: 61 / 65 / 68 dB
Extraction capacity: 750 m³/hr
Recirculation capacity: 417 m³/hr
Optional extras: 1 pair ST1 Carbon filters for air recirculation
mode
DK5 1 metre length ducting kit 125 mm Ø
DK10 3 metre length ducting kit 125 mm Ø
with flat channelling included.
9

All of the optional extras are available from the Baumatic
Spares Department.
Using your Baumatic cooker hood
Before first use
IMPORTANT: THIS PROCESS MUST BE FOLLOWED
BEFORE THE COOKER HOOD IS USED FOR THE FIRST
TIME.
oYou should use a good quality stainless steel cleaner on ALL of
the stainless steel areas of your cooker hood, before it is used
for the first time.
oThis will help to leave a silicone water-resistant film to protect
the stainless steel surfaces.
To use your cooker hood
oMake sure that it has been installed by a suitably qualified
person, as per the information contained in Baumatic’s
installation instructions.
oFind the control panel, which is located at the front right of the
canopy.
oThere are two sliders on the control panel, which perform
separate functions.
1) Light control. The light can be used even when the motor is
OFF.
0 = Light OFF
1 = Light ON
10

2) Motor speed control.
= Low speed
= Medium speed
= High speed
IMPORTANT: IDEALLY YOU SHOULD SWITCH ON
YOUR HOOD TEN MINUTES BEFORE YOU START TO
COOK, OR AT THE VERY LEAST WHEN YOU BEGIN
COOKING. YOU SHOULD ALSO RUN YOUR HOOD FOR
TEN MINUTES AFTER YOU HAVE FINISHED COOKING.
Cleaning your cooker hood
IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE
THAT YOU HAVE SWITCHED YOUR COOKER HOOD
OFF AT THE OMNI-POLAR SWITCH, SET AT THE
WALL FROM THE CABLE.
Cleaning
oClean the external parts of your cooker hood with mild liquid
detergent and a new damp cloth.
oNever use abrasive powder, corrosive solvents or brushes.
oNever insert pointed objects into the motor’s protective grid.
oOnly clean the control panel and grease filter grill with mild liquid
detergents and a new damp cloth.
oIf you are using the appliance in recirculation mode, then be
sure to replace the carbon filters at the recommended interval
(see section on “Fitting the carbon filter”). A build up of grease
could cause a fire hazard.
oNever attempt to clean the area above the grease filter.
oIMPORTANT: You should regularly use a good quality
stainless steel cleaner to maintain the shine and finish on
the stainless steel areas of your cooker hood.
oThis will help to leave a silicone water-resistant film to protect
the stainless steel surfaces and keep them in good condition for
the life of the product.
11

The grease filter
oYour cooker hood includes a grease filter which helps to absorb
grease particles to protect your kitchen and furniture from
greasy residues.
oThe metallic filter may become flammable if it becomes
saturated with greasy residue.
oTo prevent this fire hazard, the filter should be cleaned regularly.
Depending on use, this should be done every 10-15 days or at
least once a month, using hot water and normal washing-up
detergent.
oDO NOT WASH THE GREASE FILTER IN A DISHWASHER.
Maintenance
Removing and cleaning the grease filter
oFirst remove the grease
filters by pulling down on the
handle and pulling them away
from the cooker hood.
oSoak the grease filter in hot water and washing up liquid for
about an hour.
oRinse it off thoroughly with hot water.
12
oRepeat the process if required.

oRefit the grease filter once it
has dried.
oIMPORTANT: Let the
grease filter dry
thoroughly before
refitting it in the cooker
hood.
Changing a light bulb
13
described on page 12).
at they have cooled
down.
d it
located in the light fixture which
the canopy.
oPress gently on the underside of the bulb that needs to be
replaced and twist anticlockwise to release.
IMPORTANT: BEFORE ATTEMPTING TO CHANGE
A LIGHT BULB, YOU MUST ENSURE THAT YOU
HAVE DISCONNECTED THE COOKER HOOD FROM
YOUR MAINS SUPPLY.
oRemove the grease filter (as
oPrior to touching the light bulbs
ensure th
oFind the bulb that requires
replacement, you will fin
is inside the exposed section of

14
T: Defective bulbs should be replaced immediately.
are fitted
before you call for technical
oRefit the grease filter.
e
b
FORE ATTEMPTING TO FIT OR
REMOVE THE CARBON FILTERS, YOU MUST
oYou will find that one filter will attach over the front of the fan
arbon filter must be replaced at least every
peration when
oRemove the grease filters.
oInsert a new identical 40W (max) bulb.
oIMPORTAN
oIf the lights still do no
properly into their housings
assistance.
t work, make sure that the bulbs
Fitting the carbon filter
is going to be used in recirculation mode then it is
fit a carbon filter. This will help to absorb unpleasant
y cooking.
If the applianc
necessary to a
odours caused
IMPORTANT: BE
ENSURE THAT YOU HAVE DISCONNECTED THE
COOKER HOOD FROM YOUR MAINS SUPPLY.
motor. The active c
four months d
in recirculation mode.
epending on usage to allow normal o

15
2) Hook the carbon filter over the
pins that are located at the end of
the motor.
) Turn the carbon filter clockwise until you feel it latch
nto the motor’s sides.
grease filters.
oWhen replacing the carbon filter, follow the steps outlined above
and turn the carbon filter anti-clockwise to unlatch it from the
motor.
3
o
4) Replace the

InstallationInstallation
IMPORTANT: Before installation read all the
instructions and make sure that the voltage (V)
es all responsibility in the event of the installer
YOUR COOKER HOOD IS INTENDED FOR FITTED AND
PERMANENT INS
nd N (neutral) in the hood and fixed
and the frequency (Hz) indicated on the rating
plate are exactly the same as the voltage and
frequency in your home. The rating plate can be
found behind the grease filters.
The manufacturer declin
failing to observe all the accident prevention regulations in force,
which are necessary for normal use and the regular opera
electric system. tion of the
Electrical connection
TALLATION.
oIf not supplied the power cable must be connected to the
terminals marked L (live) a
with a cable clamp.
oThe cooker hood’s power cable must be fitted upstream
electrical connection, using an omni-polar switch with
distance of at least 3 mm.
from the
a contact
16 16
WARNING: THIS APPLIANCE MUST NOT BE
EARTHED. It should only be connected by a competent
person, using fixed wiring via a double pole switched fused
spur outlet. (UK ONLY). The fuse must be rated at 3
amps.
We recommend that the appliance is connected by a qualified
is a member of the N.I.C.E.I.C. and who will comply
th the I.E.E. and local regulations. The wires in the mains lead are
electrician, who
wi
coloured in accordance with the following UK code:

17
lue = Neutral
’s lead (blue and
rown); neither must be connected to the earth terminal.
s:
arked “N” (neutral), or
coloured black.
oThe brown wire must be connected to
at the product purchased is of a suitable size for the
chosen installation area. In addition check whether there is an
e product is going to be used in extraction mode,
then there should also be space to connect a ducting hose to the
oCarry out all necessary masonry work prior to the fitting of the
oEnsure that all electrical connections are carried out by a suitably
hould be removed.
oIf possible, disconnect and move freestanding or slot-in cookers
he worktop, hob top or cooker. This will
help to protect these surfaces from damage and debris.
B
Brown = Live
You will find only find two wires in the main
b
oAs the colours
correspond with
in your spur box,
of the wires in the appliance’s mains lead may not
the coloured markings identifying the terminals
please proceed as follow
oThe blue wire must be connected to
the terminal m
the terminal marked “L” (live), or
coloured red.
Before beginning installation
oCheck th
electrical socket available that will be accessible once the hood is
mounted. If th
outside.
cooker hood.
qualified person.
oBefore commencing installation of the cooker hood the grease
filter s
oCheck inside the product and ensure that there is no transit
packaging or any other materials, such as packets of screws,
guarantees etc. These should be removed and kept for future
use.
from their position, to provide easier access to the rear wall and
ceiling. If this is not possible, then a thick, protective covering
should be placed over t

18
nd fittings on it.
ilicone this appliance to the wall or
cabinetry. This appliance is designed to be surface mounted
only.
y
OUR COOKER HOOD WHETHER TO USE
IT IN EXTRACTION MODE OR RECIRCULATION
22 NOW TO
UNDERSTAND THE DIFFERENCES BETWEEN THESE
oWe recommend that two people install this hood.
D SHOULD BE CONNECTED
TO YOUR MAINS SUPPLY AFTER
oSelect a flat surface for assembling the cooker hood. Cover that
surface with a protective covering and place all cooker hood
parts a
oDo not tile, grout or s
Installing
our cooker hood
IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE
INSTALLING Y
MODE. PLEASE TURN TO PAGE 21-
TWO MODES.
oYour cooker hood should only be fitted into the underside of a
kitchen unit.
oIt must be positioned at least 700 mm above the hob
underneath it. You cannot fit this product by securing it between
two cupboards.
IMPORTANT: YOUR COOKER HOO THE REST OF THE
) Remove the metal grease filter (A).
) Create an opening in the underneath of the kitchen unit; the cut-
INSTALLATION PROCESS HAS BEEN COMPLETED.
1
2
out must be of the dimensio
CAN52.3ME
ns shown in the drawing below.
CAN75.3SS

19
our cooker hood to
external ducting, then you must complete the steps listed in the
for the electrical cable
to feed through. Remove the 4 screws securing the extractor frame
the two support clips on either side of the
are set to accommodate the thickness of the mounting surface,
4) Lift the cooker hood towards the cut-out that you made in step 2.
Feed the electrical cable through the hole that you made in step 3.
IMPORTANT: Do not connect the electrical cable to the mains supply
at this stage.
5) Lift the cooker hood fully into the cut out that you made in step 2.
If you are connecting the cooker hood to external ducting, then secure
the ducting hose to the coupling on the appliance.
oOne person should support the hood. The other person should
replace the extractor frame using the 4 screws (B) and fully
tighten the 4 support screws through the pre-drilled holes in the
oIMPORTANT: If you are going to connect y
“Connecting to external ducting” section before carrying on with
the rest of the installation (this information can be found on
page 20).
3) Make a hole in the inside of the kitchen unit
(B) to the hood. Ensure that
oodh
by adjusting the clip via the screw.
outer frame of the hood, into the kitchen unit. Make sure that all
of the support screws are fully tightened.
oRefit the grease filter.

20
onnecting to external ducting
ood, using two of
e between the coupling and your discharge
outlet should be 3 metres, wi
t
unit, you should
he coupling in the
Completing the installation
oIf you
should
filters” n pages 14-15.
irement noted on the rating plate, which is placed inside the
cooker hood. The appliance should now be connected to the
C
the cooker h
ed.
oConnect the coupling to the top of
the smaller screws provid
oConnect a Ø125 mm ducting hose to a discharge outlet that is
suitable for cooking vapours.
oThe discharge outlet should have a cross section of at least 150
cm² (please note that the ducting hose is not supplied with the
appliance but one can be obtained from the Baumatic Spares
Department).
oThe maximum distanc th one 90 degree bend. For each
ditional 90 degree bend, the maximum distance is reduced by
her metre.
xing the cooker hood into the kitchen
ad
a fur
oBefore fi
connect the other end of the ducting hose to t
top of the cooker hood.
are setting the appliance to recirculation mode, then you
now fit the two carbon filters. See the “Fitting the carbon
section o
oThe electrical connection must correspond to the electrical
requ
electrical supply. See page 16-17 for detailed information on the
electrical connection.
oRefit the grease filter and then switch on the mains
supply to the appliance. Check that the appliance is