Baumer Camera Link HXC20 User manual

Dimensions HXC20/40 C-Mount
52
52
26 26
36
36
UNC 1/ 4-20
16 x M3 depth 6
26 36
36
36
4 x M3 depth 6
37,4
Dimensions HXC20/40 F-Mount
52
52
26 26
3636
UNC 1/4-20
16 x M 3 depth 6
26 36
37
Safety
Further Information
For further information on our products visit www.baumer.com
For technical issues, please contact our technical support:
[e-mail]· Phone [phone] · Fax [phone]
© Baumer Optronic GmbH · Badstrasse 30 · DE-01454 Radeberg, Germany
Technical data has been fully checked, but accuracy of printed cannot be guaranteed.
Subject to change without notice. Printed in Germany 06/14. v1.7 11054752
FCC – Class B device
No t e : This equipment has been tested and found to
comply with the limits for a Class B digital device, pursu-
ant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interfer-
ence in a residential environment. This equipment gener-
ates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructios,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occure in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off an
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.▪
Increase the separation between the equipment and the▪
receiver.
Connect the equipment into an outlet on a circuit different▪
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician▪
for help.
Conformity:
CE, FCC Part 15 Class B, RoHS
Quick Start Guide
HXC cameras –Release 2 (Camera Link®)
Installation
Installation using
Camera Link®BASE:
Connect the camera using▪
an appropriate cable to the
framegrabber board on your
PC using the lower sdr-26
jack on the camera side
If required, connect a strobe▪
to the connector
Connect the camera to▪
power supply
Installation using
Camera Link®MEDIUM /
FULL:
Connect the camera using▪
two appropriate cables to
the framegrabber board on
your PC (this configuration
requires the BASE and the
FULL Camera Link®line)
If required, connect a strobe▪
to the connector
Connect the camera to▪
power supply
Installation sample
1 - Framegrabber board; 2 - CameraLink®cable;
3 - Process interface cable; 4 - Power cable
Installation sample
1 - Framegrabber board; 2 - CameraLink®cable;
3 - Process interface cable; 4 - Power cable
Product Specication
HXC cameras - Maximum Performance with CMOSIS sensors
Camera Link▪®Full progressive scan CMOS camera
Excellent image quality▪
Global shutter architecture for minimized motion blur▪
Low noise due to correlated double sampling (CDS)▪
HDR (High Dynamic Range)▪
Enhanced NIR sensitivity model available▪
Binning, subsampling and true partial scan function (ROI) for increased frame▪
rates
External synchronization via industrial compliant process interface (trigger / flash)▪
Integrated supplementary function for flexible integration▪
Integrated 256 MByte RAM for temporarily image data buffering▪
Two standard 26 pin Mini-CameraLink▪®connectors
Support for CameraLink▪®Base, Medium, Full and 10 tap configurations
Baumer GAPI: Flexible, generic software interface for Windows▪
Camera Type Sensor
Size Resolution Full Frames [max. fps]
Monochrome
HXC20 2/3“ 2048 x 1088 337
HXC40 1“ 2048 x 2048 180
Color
HXC20c 2/3“ 2048 x 1088 337
HXC40c 1“ 2048 x 2048 180
Safety instructions
Notice
See User´s Guide for the com-
plete safety instructions!
Protect the sensor from dirt and▪
moisture.
Never open the camera housing.▪
Avoid camera contamination by▪
foreign objects.
Environmental requirements:
Storage temp. -10 °C ... +70 °C
(14 °F...158 °F)
Operating temp. +5 °C ... +60 °C
(41 °F...140 °F)
Housing temp. max. +65 °C
(max. 149 °F)
Humidity 10 % ... 90 %
Non-condensing
Latest software version and technical
documentation are available at:
www.baumer.com/vision/login

Camera Link®Interfaces
Notice
Ba u me r
Type: HXCXXx (xxxxxxx)
S/N: 000XXXXX R1.0
CL FULL
CL BASE
C
LBA
S
E
C
LF
U
L
L
The camera has two CameraLink sockets. To differentiate bet-
ween CameraLink Base and CamerLink Full socket, please look
at the label. You can not use the CL Full socket alone!
Caution
When xing the CameraLink®cable with too much force the
screws might get damaged.
The maximum torque is 2.5 inch lbf [0.3 Nm].
Base Camera Link®Full Camera Link®
Pin Signal Pin Signal Pin Signal Pin Signal
1GND 14 GND 1GND 14 GND
2X0- 15 X0+ 2Y0- 15 Y0+
3X1- 16 X1+ 3Y1- 16 Y1+
4X2- 17 X2+ 4Y2- 17 Y2+
5XCLK- 18 XCLK+ 5YCLK- 18 YCLK+
6X3- 19 X3+ 6Y3- 19 Y3+
7SERTC+ 20 SERTC- 7100 Ω term. 20 100 Ω term.
8SERTFG- 21 SERTFG+ 8Z0- 21 Z0+
9CC1- 22 CC1+ 9Z1- 22 Z1+
10 CC2+ 23 CC2- 10 Z2- 23 Z2+
11 CC3- 24 CC3+ 11 ZCLK- 24 ZCLK+
12 CC4+ 25 CC4- 12 Z3- 25 Z3+
13 GND 26 GND 13 GND 26 GND
LED Signaling
2
1
LED Signal Meaning
1
green Power on
yellow Readout active
2
green Transmitting
red (yellow in both) Conguration comman
processing
Power Supply / IO Pin Assignment
Caution
A power supply with electrical isolation is required for proper operati-
on of the camera. Otherwise the device may be damaged.
M8 / 3 pins M8 / 8 pins
wire colors of the connecting cable
1
4
3
8
5
7 3
1
4
2
6
1(brown) Power VCC 1(white) Line 9
3(blue) GND 2(brown) Line 1
4(black) NC 3(green) Line 0
4(yellow) GND
5(grey) Uext
6(pink) Line 7
7(blue) Line 8
8(red) Line 2
Power Supply
Power VCC 9,6 VDC .. 30 VDC
I 200 mA .. 625 mA
Heat Transmission
Caution
Provide adequate dissipation of heat, to ensure that the temperature
does not exceed the spedied temperature.
The surface of the camera may be hot during operation and imme-
diately after use. Be careful when handling the camera and avoid
contact over a longer period.
T T
It is very important to provide adequate dis-
sipation of heat, to ensure that the housing
temperature does not reach or exceed +65 °C
(+149°F). As there are numerous possibilities for
installation, a specic method for proper heat dis-
sipation is not dened, but the following principles
are suggested:
Operate the cameras only in mounted▪
condition with a good heat conductor
(e.g. aluminum)
Mounting in combination with forced▪
convection may provide proper heat
dissipation
T: Housing temperature
measurement point
General Description
123
4
56
No. Description No. Description
1(respective) lens mount 4Digital-IO supply
2Power supply 5CameraLink®Base socket
3CameraLink®Full socket 6Signaling-LED