Baumer VEXU Series User manual

Safety
Further Information
For further information about our products, please visit www.baumer.com
For technical issues, please contact our technical support:
[email protected] · Phone [phone] · Fax [phone]
© Baumer Optronic GmbH · Badstrasse 30 · DE-01454 Radeberg, Germany
Technical data has been fully checked, but accuracy of printed matter is not guaranteed.
The information in this document is subject to change without notice.
Printed in Germany 04/18. v13 11164079
CE
We declare, under our sole responsibility, that
the previously described Baumer VEXU camer-
as conform with the directives of the CE.
RoHS
All VEXU cameras comply with the recom-
mendation of the European Union concerning
RoHS Rules.
Safety Precautions
Notice
See the User's Guide for the
complete safety instructions!
Caution
Observe precautions for
handling electrostatically
sensitive devices!
▪Protect the sensor from dirt and
moisture.
▪Do not allow the camera to become
contaminated with foreign objects.
Environmental Requirements
Storage temp. -10 ° C ... +70 °C
Operating temp. see Heat Trans-
mission
Humidity 10 % ... 90 %
Non-condensing
Quick Start Guide
VEXU cameras (USB 3.0)
Latest software version and technical
documentation available at:
vt.baumer.com
Conformity:
CE, RoHS
System Requirements
Single-camera system
Recommended
Multi-camera system
Recommended
CPU Intel®Core™i5-2520M
CPU @ 2.50 GHz, Cores: 4
Intel®Core™i7-3770
CPU @ 3.40 GHz, Cores: 8
RAM 4 GB 8 GB
Operating
system
(OS)
Microsoft®Windows® 7 32 / 64 bit systems (required for USB 3.0)
Microsoft®Windows®8 32 / 64 bit systems (required for USB 3.0)
Microsoft®Windows®10 32 / 64 bit systems (required for USB 3.0)
Product Specication
VEXU cameras – Integrating essential basic functionalities
▪up to 2.3 Megapixel
▪up to 217 fps
▪29 × 29 mm housing with all-sided M3 mount
▪Global shutter architecture for minimized motion blur
▪Integrating essential basic functionalities
▪USB bus powered
▪USB VisionTM standard compliant
Notice
Further technical details are available in the respective data sheets.
Installation
Lens Mount
Notice
Ensure the sensor and lens are not contaminated with dust and airborne
particles when mounting the support or the lens to the device!
The following points are very important:
▪Install the camera in an environment that is as dust free as possible!
▪Keep the dust cover (bag) on the camera for as long as possible!
▪Hold the camera with the sensor downwards if the sensor is uncovered.
▪Avoid contact with any of the camera‘s optical surfaces!
Dimensions
29
29
20
18
6,15
8,2
6
20
3
28,7
20
22
30
CS-mount
1,55 ±0,3537,88,4
3
8 x M3 x 4
2 x M3 x 4
ø

Data Interface / Digital IOs
USB 3.0 (Micro B)
12345678910
1VBUS 6MicB_SSTX-
2D- 7MicB_SSTX+
3D+ 8GND_DRAIN
4ID 9MicB_SSRX-
5GND 10 MicB_SSRX+
Digital-IOs (on camera side)
wire colors of the connecting cable (ordered separately)
1
2
4
3
1Power IO brown 3GND blue
2IN1 (Line0) white 4OUT1 (Line1) black
General Description
2
43
1
No. Description No. Description
1Lens mount (CS-mount) 4LED
2Digital IO
3USB 3.0 port
LED signals
LED
Signal Meaning
LED
green ash Power on
green USB 3.0 connection
red USB 2.0 connection
yellow Readout active
red ash Update
Installation
Installing the camera:
▪Connect the camera to the USB connection on your PC using an appropriate
cable.
▪If required, connect a trigger and / or flash to the digital IOs.
open wire
Installation example
1- PCI USB board
2- USB cable
3 - Cable for trigger and ash
Troubleshooting
1. Check camera operation using the LED signals.
→ If LED is red:
• Camera is connected to USB 2.0 (settings possible).
2. Check connection using Windows Device Manager:
→ If device is not listed:
• Check the host controller power supply.
• Check USB 3.0 cable and connection.
→ If device is regularly not listed
• Check USB 3.0 driver installation.
Heat Transmission
Caution
Heat can damage the camera. Heat must be dissipated adequately
to ensure that the temperature does not exceed the values in the
table below.
As there are numerous possibilities for installation, Baumer recom-
mends no specic method for proper heat dissipation, but suggest
the following principles:
▪operate the cameras only in mounted condition
▪mounting in combination with forced convection may provide
proper heat dissipation
T
Measurement Point Maximum Temperature
Measurement Point (T) 65°C (149°F)