Baumer CiA DS-301 User manual

Baumer Hübner GmbH
Max-Dohrn-Str. 2+4
D-10589 Berlin
Phone [phone] - 0
Fax [phone]
[email protected]
www.baumer.com
Manual
Absolute Encoder with
Firmware version from 1.00

BUDE_Manual-CANopen_EN.doc 2/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
Contents
Page
1Introduction.....................................................................................................................................4
1.1 Scope of delivery..............................................................................................................................4
1.2 Product assignment..........................................................................................................................4
2Safety and operating instructions................................................................................................5
3CAN bus and CANopen communication......................................................................................7
3.1 CAN bus...........................................................................................................................................7
3.1.1 CAN bus characteristics...................................................................................................................7
3.2 CANopen..........................................................................................................................................8
3.3 CANopen communication.................................................................................................................9
3.3.1 Communication profile......................................................................................................................9
3.3.2 CANopen message structure...........................................................................................................9
3.3.3 Service data communication..........................................................................................................10
3.3.4 Process data communication.........................................................................................................12
3.3.5 Emergency service.........................................................................................................................14
3.3.6 Network management services......................................................................................................15
3.3.7 Layer Setting Services ...................................................................................................................19
3.4 Encoder/converter profile...............................................................................................................23
3.4.1 Overview of encoder/converter objects..........................................................................................23
3.4.2 Detailed object list (DS-301)...........................................................................................................27
4Diagnosis and useful information ..............................................................................................44
4.1 Error diagnosis field bus communication .......................................................................................44
4.2 Error diagnosis via field bus...........................................................................................................44
4.3 Useful information relating to the sensor........................................................................................45
5Applications..................................................................................................................................46
5.1 Setting and reading objects............................................................................................................46
5.2 Configuration..................................................................................................................................47
5.3 Operation........................................................................................................................................49
5.4 Use the encoder via CAN interface................................................................................................51
6Terminal assignment and commissioning.................................................................................53
6.1 Electrical connection ......................................................................................................................53
6.1.1 Setting the user address ................................................................................................................53
6.1.2 Setting the baud rate......................................................................................................................53
6.1.3 Terminating resistor........................................................................................................................53
6.1.4 Bus cover connection.....................................................................................................................54
6.1.5 Terminal assignment ......................................................................................................................55
6.2 Display elements (status display)...................................................................................................55

BUDE_Manual-CANopen_EN.doc 3/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
Disclaimer of liability
The present manual was compiled with utmost care, errors and omissions reserved. For this reason Baumer
Huebner GmbH rejects any liability for the information compiled in the present manual. Baumer Huebner
GmbH nor the author will accept any liability for direct or indirect damages resulting from the use of the
present information.
At any time we should be pleased receiving your comments and proposals for further improvement of the
present document.

BUDE_Manual-CANopen_EN.doc 4/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
1 Introduction
1.1 Scope of delivery
Please check the delivery upon completeness prior to commissioning.
Depending on encoder configuration and part number delivery is including:
•Basic encoder or HEAG162SC with CANopen bus cover
•CD with EDS file and manual (also available as download in the internet).
1.2 Product assignment
Shaft encoder
Product Product code eds file Product family
AMG 11 C 13 0x0B CO13.eds AMG 11 – Singleturn 13 Bit
AMG 11 C 29 0x0A CO29.eds AMG 11 – Multiturn 29 bit
AMG 81 C 13 0x0B CO13.eds AMG 81 – Singleturn 13 bit
AMG 81 C 29 0x0A CO29.eds AMG 81 – Multiturn 29 bit
Hollow / Endshaft encoder
Product Product code eds file Product family
HMG 11 C 13 0x0B CO13.eds HMG 11 – Singleturn 13 bit
HMG 11 C 29 0x0A CO29.eds HMG 11 – Multiturn 29 bit
HEAG 162 converter
Product Product code eds file Product family
HEAG 162 SC 13 0x0B CO13.eds HEAG 162 converter 13 bit
HEAG 162 SC 18 0x0F CO18.eds HEAG 162 converter 18 bit
HEAG 162 SC 29 0x0A CO29.eds HEAG 162 converter 29 bit

BUDE_Manual-CANopen_EN.doc 5/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
2 Safety and operating instructions
Supplementary information
•This manual is intended as a supplement to already existing documentation (catalogues, data sheets
and assembly instructions). They are placed on the delivered CD or can be downloaded at
www.baumer.com.
•The manual must be read without fail before initial commissioning of the equipment.
Intended purpose of the equipment
•The AMG/HMG is a precision measurement device. It is used to determine angular positions and
revolutions, and to prepare and supply measured values in the form of electrical output signals for the
follow-on device systems. The AMG/HMG may only be used for this purpose.
•The HEAG is a signal converter which reads cyclically data words as ssi master. It provides the data
words to transmit them via CANopen. The HEAG may only be used for this purpose.
Commissioning
•The encoder/converter may only be installed and assembled by suitably qualified experts.
•Observe the operating instructions of the machine manufacturer.
Safety remarks
•Prior to commissioning the equipment, check all electrical connections.
•If installation, electrical connection or any other work performed at the encoder or at the equipment is not
correctly executed, this can result in a malfunction or failure of the encoder.
•Steps must be taken to exclude any risk of personal injury, damage to the plant or to the operating
equipment as a result of encoder failure or malfunction by providing suitable safety precautions.
•Encoders must not be operated outside the specified limited values (see detailed product
documentation).
Failure to comply with the safety remarks can result in malfunctions, personal injury or damage to property.
Transport and storage
•Only ever transport or store encoders in their original packaging.
•Never drop encoders or expose them to major vibrations.
Assembly
•Avoid impacts or shocks on the housing and shaft.
•Avoid any twist or torsion on the housing.
•Do not open the encoder or make any mechanical changes to it.
The shaft, ball bearings, glass pane or electronic components can be damaged. In this case, safe and
reliable operation cannot be guaranteed.

BUDE_Manual-CANopen_EN.doc 6/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
Electrical commissioning
•Do not make any electrical changes at the encoder/converter.
•Do not carry out any wiring work when the encoder/converter is live.
•Never plug or unplug the electrical connection when the encoder/converter is live.
•Ensure that the entire plant is installed in line with EMC requirements. The installation environment and
wiring affect the electromagnetic compatibility of the encoder/converter. Install the encoder/converter and
supply cables separately or at a long distance from cables with high interference emissions (frequency
converters, contactors etc.)
•Where working with consumers which have high interference emissions, make available a separate
power supply for the encoder/converter.
•Completely shield the encoder/converter housing and connecting cable.
•Connect the encoder to the protective earth (PE) conductor using shielded cable. The braided shield
must be connected to the cable gland or plug. Ideally, aim at bilateral connection to protective earth (PE),
the housing via the mechanical assembly, the cable shield via the downstream connected devices. In
case of earth loop problems, earth on one side only as a minimum requirement.
Failure to observe these instructions can result in malfunctions, material damage or personal injury.
Disposal
•Dispose of encoder/converter in accordance with locally applicable legislation.

BUDE_Manual-CANopen_EN.doc 7/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
3 CAN bus and CANopen communication
3.1 CAN bus
The CAN bus (CAN: Controller Area Network) was originally developed by Bosch and Intel as a means of
fast, low-cost data transmission in automotive applications. The CAN bus is used today also in industrial
automation applications.
The CAN bus is a field bus (the standards are defined by the CAN in Automation (CiA) Association) through
which devices, actuators and sensors from different manufacturers can communicate with each other.
3.1.1 CAN bus characteristics
• Data rate of 1 MBaud with network expansion up to 40 m
• Network connected on both sides
• The bus medium is a twisted-pair cable
• Real time capability: Defined maximum waiting time for high-priority messages.
• Theoretically 127 users at one bus, but physically only 32 are possible (due to the driver).
• Ensures data consistency across the network. Damaged messages are notified as faulty for all network
nodes.
• Message-oriented communication
The message is identified by a message identifier.All network nodes use the identifier to test whether the
message is of relevance for them.
• Broadcasting, multicasting
All network nodes receive each message simultaneously. Synchronization is therefore possible.
• Multimaster capability
Each user in the field bus is able to independently transmit and receive data without being dependent upon
the priority of the master. Each user is able to start its message when the bus is not occupied. When
messages are sent simultaneously, the user with the highest priority prevails.
• Prioritization of messages
The identifier defines the priority of the message. This ensures that important messages are transmitted
quickly via the bus.
• Residual error probability
Safety procedures in the network reduce the probability of an undiscovered faulty data transmission to
below 10 -11. In practical terms, it is possible to ensure a 100% reliable transmission.
• Function monitoring
Localization of faulty or failed stations. The CAN protocol encompasses a network node monitoring
function. The function of network nodes which are faulty is restricted, or they are completely uncoupled
from the network.
• Data transmission with short error recovery time
By using several error detection mechanisms, falsified messages are detected to a high degree of
probability. If an error is detected, the message transmission is automatically repeated.
In the CAN Bus, several network users are connected by means of a bus cable. Each network user is able to
transmit and receive messages. The data between network users is serially transmitted.
Examples of network users for CAN bus devices are:
• Automation devices such as PLCs
• PCs
• Input and output modules
• Drive control systems
• Analysis devices, such as a CAN monitor
• Control and input devices as Human Machine Interfaces (HMI)
• Sensors and actuators

BUDE_Manual-CANopen_EN.doc 8/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
3.2 CANopen
Under the technical management of the Steinbeis Transfer Centre for Automation, the CANopen profile was
developed on the basis of the Layer 7 specification CAL (CAN Application Layer). In comparison with CAL,
CANopen only contains the functions suitable for this application. CANopen thus represents only a partial
function of CAL optimized for the application in hand, so permitting a simplified system structure and the use
of simplified devices. CANopen is optimized for fast data exchange in real time systems.
The organization CAN in Automation (CiA) is responsible for the applicable standards of the relevant profiles.
CANopen permits:
• Simplified access to all device and communication parameters
• Synchronization of several devices
• Automatic configuration of the network
• Cyclical and event-controlled process data communication
CANopen comprises four communication objects (COB) with different characteristics:
• Process data objects for real time data (PDO)
• Service data objects for parameter and program transmission (SDO)
• Network management (NMT, Heartbeat)
• Pre-defined objects (for synchronization, emergency message)
All device and communication parameters are subdivided into an object directory. An object directory
encompasses the name of the object, data type, number of subindexes, structure of the parameters and the
address. According to CiA, this object directory is subdivided into three different parts. Communication
profile, device profile and a manufacturer-specific profile (see object directory).

BUDE_Manual-CANopen_EN.doc 9/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
3.3 CANopen communication
3.3.1 Communication profile
Communication between the network users and the Master (PC / Control) takes place by means of object
directories and objects. The objects are addressed via a 16 bit index. The CANopen communication profile
DS 301 standardizes the various communication objects. They are accordingly divided into several groups:
• Process data objects PDO for real time transmission of process data
• Service data objects SDO for read/write access to the object directory
• Objects for synchronization and error display of CAN users:
SYNC object (synchronization object) for synchronization of network users
EMCY object (emergency object) for error display of a device or its peripherals
• Network management NMT for initialization and network control
• Layer Setting Services LSS for configuration by means of serial numbers, revision numbers etc. in the
middle of an existing network
3.3.2 CANopen message structure
The first part of a message is the COB ID (Identifier).
Structure of the 11-bit COB ID :
Function code
Node ID
4-bit function code
7-bit node ID
The function code provides information on the type of message and priority
The lower the COB ID, the higher the priority of the message
Broadcast messages:
Function code
COB ID
NMT
0h
SYNC
80h
Peer to peer messages:
Function code
COB ID
Emergency
80h + Node ID
PDO1 (tx)1)
180h + Node ID
PDO2 (tx)1)
280h + Node ID
SDO (tx)1)
580h + Node ID
SDO (rx)1)
600h + Node ID
Heartbeat
700h + Node ID
LSS (tx)1)
7E4h
LSS (rx)1)
7E5h
1): (tx) and (rx) from the viewpoint of the encoder
The node ID can be freely selected by means of the CANopen bus between 1 and 127 (if rotary switches =
0). The encoders are supplied with the Node ID 1.
This can be changed with the service data object 2101h or using LSS.
A CAN telegram is made up of the COB ID and up to 8 bytes of data:
COB ID
DLC
Byte 1
Byte 2
Byte 3
Byte 4
Byte 5
Byte 6
Byte 7
Byte 8
xxx
x
xx
xx
xx
xx
xx
xx
xx
xx
The precise telegram is outlined in more detail at a later point.

BUDE_Manual-CANopen_EN.doc 10/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
3.3.3 Service data communication
The service data objects correspond to the standards of the CiA. It is possible to access an object via index
and subindex. The data can be requested or where applicable written into the object.
General information on the SDO
Structure of an SDO telegram:
COB ID
DLC
Command
Object L
Object H
Subindex
Data 0
Data 1
Data 2
Data 3
An SDO-COB ID is composed as follows:
Master -> Encoder/Converter : 600h + Node ID
Encoder/Converter -> Master : 580h + Node ID
DLC (data length code) describes the length of the telegram. This is composed as follows:
1 byte command + 2 bytes object + 1 byte subindex + no. of data bytes (0 - 4).
The command byte defines whether data is read or set, and how many data bytes are involved.
SDO command
Description
Data length
22h
Download request
Max. 4 Byte
Transmits parameter to encoder/converter
23h
Download request
4 byte
2Bh
Download request
2 byte
2Fh
Download request
1 byte
60h
Download response
-
Confirms receipt to master
40h Upload request - Requests parameter from
encoder/converter
42h
Upload response
Max. 4 byte
Parameter to master with max. 4 byte
43h
Upload response
4 byte
4Bh
Upload response
2 byte
4Fh
Upload response
1 byte
80h Abort message - Encoder/converter signals error code to
master

BUDE_Manual-CANopen_EN.doc 11/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
An abort message indicates an error in the CAN communication. The SDO command byte is 80h. The
object and subindex are those of the requested object. The error code is contained in bytes 5 – 8.
ID
DLC
Byte 1
Byte 2
Byte 3
Byte 4
Byte 5
Byte 6
Byte 7
Byte 8
580h + Node ID
8
80h
Object L
Object H
Subindex
ErrByte 0
ErrByte 1
ErrByte 2
ErrByte 3
Byte 8 - 5 results in the SDO abort message (byte 8 = MSB).
The following messages are supported:
05040001h : Command byte is not supported
06010000h : Incorrect access to an object
06010001h : Read access to write only
06010002h : Write access to read only
06020000h : Object is not supported
06090011h : Subindex is not supported
06090030h : Value outside the limit
06090031h : Value too great
08000000h : General error
08000020h : Incorrect save signature
08000021h : Data cannot be stored

BUDE_Manual-CANopen_EN.doc 12/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
SDO examples
Request of a value by the master from the slave
A frequent request will be a request for position. Object 6004h
COB ID DLC Command Object L Object H Subindex
Data 0 Data 1 Data 2 Data
3
600h+node ID
8
40h
04h
60h
0h
x
x
x
x
Response by the slave to the request for a value
The position is 4 bytes long, the precise values can be found under object 6004h.
COB ID DLC Command Object L Object H Subindex
Data 0 Data 1 Data 2 Data
3
580h+node ID
8
43h
04h
60h
0h
a
b
c
d
Writing of a value by the master into the slave
Position setting can be performed with preset. Object 6003h
COB ID DLC Command Object L Object H Subindex
Data 0 Data 1 Data 2 Data
3
600h+node ID
8
22h
03h
60h
0h
a
b
c
d
Slave's response to the writing of a value
COB ID DLC Command Object L Object H Subindex Data 0 Data 1 Data 2
Data
3
580h+node ID
8
60h
03h
60h
0h
0h
0h
0h
0h
3.3.4 Process data communication
Process data objects are used for real time data exchange for process data, for example position or
operating status. PDOs can be transmitted synchronously or cyclically (asynchronously). The
encoder/converter supports the PDO1 and the PDO2. Both PDOs supply the current position of the
encoder/converter and are defined in the objects 1800h, 1801h, 1A00h, 1A01, 2800h, 2801h and 6200h.
Synchronous
In order to transmit the process data synchronously, a value between 1 and F0h (=240) must be written into
the object 1800h / 1801h Subindex 2. If the value is 3, the PDO is transmitted on every third sync telegram (if
the value 1 is entered, transmission takes place on every sync telegram), as long as there is a 0 written into
the object 2800h / 2801h. If it contains for example a 5, the PDO will continue to be written as before on
every third Sync telegram, but only a total of 5 times. Accordingly, the last PDO is written on the 15th sync
telegram. The counter for the number of PDOs to be transmitted is reset in the event of a position change or
NMT reset, i.e. unless it is changed, the position is transmitted five times. If the position changes, it is
transmitted a further five times.
In synchronous operation, the PDO is requested by the master via the Sync telegram.
Byte 0
Byte 1
COB ID = 80
0h

BUDE_Manual-CANopen_EN.doc 13/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
Cyclical (asynchronous)
If you wish the PDOs to be transmitted cyclically, the value FEh must be written into the object 1800h /
1801h Subindex 2. In addition, the cycle time in milliseconds must be entered in the same object Subindex 5.
The entered time is rounded off to 1 ms. If the value is stored for 0 ms, the PDOs are not transmitted. The
function is switched off.
The object 2800h / 2801h offers another possibility: If the value is 0, cyclical transmission runs as described
above. If the value is 1, a cyclical test is performed as to whether a change of the value has occurred. If not,
no transmission takes place. If the value is 4, the PDO is transmitted four times with each cycle if there is a
change.
Overview
In the following table, the different transmission modes for PDOs are summarized:
1800h
2800h Summarized description
Sub2
Sub5
FEh
3ms
0
Cyclical transmission every 3 ms
FEh
5ms
2
Every 5 ms, the PDO is sent twice if there is a change
FEh
0ms
0
Transmit PDO switched off
FEh
0ms
xxx
Transmit PDO switched off
3
xxx
0
Transmit with every third sync telegram
3
xxx
2Bh
On every third sync telegram, but only 43 times in total (=2Bh).
PDO (Position)
PDO1 telegram structure:
ID
DLC
Byte 1
Byte 2
Byte 3
Byte 4
181h
4
xx
xx
xx
xx
ID : 180h + node ID
Length : 4 DataByte
Byte1 - 4 : Current position in increments
PDO2 telegram structure:
ID
DLC
Byte 1
Byte 2
Byte 3
Byte 4
281h
4
xx
xx
xx
xx
ID : 280h + node ID
Length : 4 DataByte
Byte1 - 4 : Current position in increments

BUDE_Manual-CANopen_EN.doc 14/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
3.3.5 Emergency service
Internal device error or bus problems initiate an emergency message:
COB ID
DLC
Byte0
Byte 1
Byte 2
Byte 3
Byte 4
Byte 5
Byte 6
Byte 7
80h+node ID 8
Error code
Error register
1001h
Alarms 6503h Warning 6505h -
00h
01h
Byte 0 - 1: Error codes
Error Code (hex)
Meaning
0000h
Error reset or no error
1000h
Generic error
5530h
EEPROM error (from V1.04)
6010h
Software reset (Watchdog) (from V1.04)
7320h
Position error (from V1.04)
7510h
Internal communication error (from V1.04)
8130h
Life Guard error or Heartbeat error (from V1.04)
FF00h
Battery low (ab V1.04) (onlyAMG 81 C 29)
Byte 2: Error register
Bit
Meaning
0h
Generic error
4h
Communication error (from V1.04)
7h
Manufacturer specific (from V1.04)
Byte 3 - 4 Alarms
Bit
Meaning
Value = 0
Value = 1
0
Position error active
No
Yes
Byte 5 - 6 Warning
Bit
Meaning
Value = 0
Value = 1
2
CPU watchdog status
OK
Reset executed
4 Battery charge OK Charge too deep
(only AMG 81 C 29)
Byte 7: Not used

BUDE_Manual-CANopen_EN.doc 15/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
3.3.6 Network management services
Network management can be divided into two groups.
Using the NMT services for device monitoring, bus users can be initialized, started and stopped.
In addition, NMT services exist for connection monitoring.
Description of the NMT command
The commands are transmitted as unconfirmed objects and are structured as follows:
Byte 0
Byte 1
Byte 2
COB ID = 0
Command byte
Node number
The COB ID for NMT commands is always zero. The node ID is transmitted in byte 2 of the NMT command.
Command byte
Command byte
Description
In state event drawing
01h
Start remote node
1
02h
Stop remote node
2
80h
Enter pre-operational mode
3
81h, 82h
Reset remote node
4, 5
The node number corresponds to the node ID of the required users. With node number = 0, all users are
addressed.
NMT state event
Following initialization, the encoder is in the pre-operational mode. In this status, SDO parameters can be
read and written. In order to request PDO parameters, the encoder must first be moved to the operational
mode status.
Init
Pre-Operational
Operational
Stopped/Prepared
Power on oder Hardware Reset
1
3
2
1
3
2
4/5
BootUp Message
4/5
4/5

BUDE_Manual-CANopen_EN.doc 16/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
The various NMT statuses
Init
Following initalization, the encoder logs on to the CAN bus with a BootUp message. The encoder then goes
automatically to the pre-operational mode status.
The COB ID of the BootUp message is made up of 700h and the node ID.
COB ID
Byte 0
700h + node ID
00h
Pre-operational mode
In the pre-operational mode, SDOs can be read and written.
Operational mode
In the operational mode, the encoder transmits the requested PDOs. In addition, SDOs can be read and
written.
Stopped or prepared mode
In the stopped mode, only NMT communication is possible. No SDO parameters can be read or set. LSS is
only possible in the stopped mode.
Status change
Start remote node (1)
With the start command, the encoder is switched to the operational mode status.
COB ID
Command byte
Node number
0h
1h
0..127
Stop remote node (2)
With the stop command, the encoder is switched to the stopped or prepared mode status.
COB ID
Command byte
Node number
0h
2h
0..127
Enter pre-operational mode (3)
Change to the pre-operational mode status.
COB ID
Command byte
Node number
0h
80h
0..127
Reset remote node (4) or reset communication (5)
With the reset command, the encoder is re-initialized.
Reset remote node (4):
COB ID
Command byte
Node number
0h
81h
0..127
Reset communication (5):
COB ID
Command byte
Node number
0h
82h
0..127

BUDE_Manual-CANopen_EN.doc 17/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
Node and Life Guarding
The CAN in Automation association CiA
recommend to use the new heartbeat protocol
(see next chapter). To use the node guarding
instead of heartbeat protocol bit 5 of object
2110h has to be set.
To detect absent devices (e.g. because of bus-
off) that do not transmit PDOs regularly, the
NMT Master can manage a database, where
besides other information the expected states
of all connected devices are recorded, which is
known as Node Guarding.
With cyclic node guarding the NMT master
regularly polls its NMT slaves. To detect the
absence of the NMT master, the slaves test
internally, whether the Node Guarding is taking
place in the defined time interval (Life
Guarding).
The Node Guarding is initiated by the NMT
Master in Pre-Operational state of the slave by
transmitting a Remote Frame.
The NMT Master regularly retrieves the actual
states of all devices on the network by a
Remote Frame and compares them to the
states recorded in the network database.
Mismatches are indicated first locally on the NMT Master through the Network Event Service. Consequently
the application must take appropriate actions to ensure that all devices on the bus will got to a save state
"Communication error Object 1029h-1h".
Example for a nodeguarding protocol:
COB-ID
Data/Remote
Byte 0
701h
r
00h (0d)
701h
d
FFh (255d)
701h
r
00h (0d)
701h
d
7Fh (127d)
Possible NMT node states:
0: BootUp-Event
4: Stopped
5: Operational
127: Pre-operational
In other words, the encoder is in the pre-operational mode (7Fh = 127).

BUDE_Manual-CANopen_EN.doc 18/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
Heartbeat
The optional heartbeat protocol should
substitute the life/node guarding protocol.
heartbeat is activ, when Object 2110h bit 5
is '0'. It is highly recommend to implement
for new device designs the heartbeat
protocol. A heartbeat producer transmits the
heartbeat message cyclically with the
frequency defined in heartbeat producer
time object. One or more heartbeat
consumer may receive the indication. The
relationship between producer and
consumer is configurable via Object
Dictionary entries. The heartbeat consumer
guards the reception of the heartbeat within
the heartbeat consumer time. If the
Heartbeat is not received within this time a Heartbeat Event will be generated "Communication error object
1029h-1h".
Example for a heartbeat protocol
COB ID
Data/Remote
Byte 0
701h
d
7Fh (127d)
The heartbeat messages consist of the COB ID and one byte. In this byte, the NMT status is supplied.
0: BootUp event
4: Stopped
5: Operational
127: Pre-operational
In other words, the encoder is in the pre-operational mode (7Fh = 127).
Attention: Only one each of the above node guarding mechanism can be set.
Default: Heartbeat
Optional: NodeGuarding (siehe Objekt 2110h)

BUDE_Manual-CANopen_EN.doc 19/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
3.3.7 Layer Setting Services
In the spring of 2000, CiAdrafted a new protocol intended to ensure standardized occurrence. The
procedure is described under
Layer Setting Services and Protocol, CiA Draft Standard Proposal 305 (LSS).
The encoder is supplied by us as standard with the node ID 1 and a baud rate of 50 kBaud. Several
encoder/converter can be connected to the bus system with the same node ID. To allow individual
encoder/converter to be addressed, LSS is used.
Each encoder/converter is fitted with its own unique serial number and is addressed using this number. In
other words, an optional number of encoder/converter with the same node ID can be connected to one bus
system, and then initialized via LSS. Both the node ID and also the baud rate can be reset. LSS can only be
executed in the Stopped Mode.
Message structure
COB ID:
Master Slave : 2021 = 7E5h
Master Slave : 2020 = 7E4h
After the COB ID, an LSS command specifier is transmitted.
This is followed by up to seven attached data bytes.
COB ID
cs
Byte 1
Byte 2
Byte 3
Byte 4
Byte 5
Byte 6
Byte 7
Switch Mode Global
7E5h 
04h
Mode
Reserved
Mode : 0 Operation mode
1 Configuration mode
Selective switch mode
The following procedure can be used to address a certain encoder in the bus system.
7E5h 
40h
Vendor ID
reserved
7E5h 
41h
Product code
reserved
7E5h 
42h
Revision number
reserved
7E5h 
43h
Serial number
reserved
7E4h 
44h
Mode
reserved
Vendor Id : ECh
Product code : Internal product code for the respective encoder
Revision number : Current revision number of the encoder
Serial number : Unique, consecutive serial number
Mode : The encoder's response is the new mode (0=operating mode; 1=configuration mode)

BUDE_Manual-CANopen_EN.doc 20/55 Baumer Hübner GmbH
23.10.2012/bja Berlin, Germany
Setting the node ID
7E5h 
17
Node ID
reserved
7E4h 
11h
ErrCode
Spec error
reserved
Node ID : New node ID of encoder/converter
Error code : 0=OK; 1=Node ID outside range; 2 - 254=reserved; 255Specific error
Specific error : If Error code=255 application-specific error code.
Setting the bit timing
7E5h 
13h
tableSel
tableInd
reserved
7E4h 
13h
ErrCode
SpecError
reserved
TableSel : Selects the bit timing table 0 : Standard CiAbit timing table
1 - 127 : Reserved for CiA
128 - 255 : Manufacturer-specific tables
TableInd : Bit timing entry in selected table (see table below).
Error code : 0=OK; 1=Bit timing outside range; 2..254=reserved; 255Specific error
Specific error : If Error code=255 Application-specific error code.
Standard CiA table
Baud rate
Table Index
1000 kBaud
0
800 kBaud
1
500 kBaud
2
250 kBaud
3
125 kBaud
4
100 kBaud
5
50 kBaud
6
20 kBaud
7
10 kBaud
8
Saving the configuration protocol
This protocol saves the configuration parameters in the EEPROM.
7E5h 
17h
reserved
7E4h 
17h
ErrCode
SpecError
Reserved
Error code : 0=OK; 1=Saving not supported; 2=Access error; 3 - 254=reserved; 255Specific error
Specific error : If error code=255 Application-specific error code.