Baxi 739 Instructions for use

5112029/01
CERAMIC COAL FUEL EFFECT
INSTALLER AND OWNER GUIDE
THIS GUIDE IS FOR FITTING THE CERAMIC
COALFUEL EFFECT TO THE
739, 740, 741 AND 751
MODELS
ONLY
IMPORTANT
THIS GUIDE MUST BE PLACED INSIDE OR ATTACHED
TO THE INSTALLER AND OWNER GUIDE SUPPLIED
WITH THE GAS FIRE. IT MUST BE LEFT WITH THE
OWNER.
THIS GUIDE MUST BE READ IN CONJUNCTION WITH
THE INSTALLER AND OWNER GUIDE SUPPLIED WITH
THE GAS FIRE.
© Baxi Heating U.K. Ltd.

SAFETY
This product uses fuel effect pieces and burner compartment walls containing
Refractory Ceramic Fibres (RCF), which are man-made vitreous silicate fibres.
Excessive exposure to these materials may cause irritation to eyes, skin and
respiratory tract. Consequently, it is important to take care when handling these
articles to ensure that the release of dust is kept to a minimum. To ensure that the
release of fibres from these RCF articles is kept to a minimum, during installation
and servicing we recommend that you use a HEPA filtered vacuum to remove any
dust and soot accumulated in and around the fire before and after working on the
fire. When replacing these articles we recommend that the replaced items are not
broken up, but are sealed within a heavy duty polythene bag, clearly labelled as
RCF waste. This is not classified as “hazardous waste” and may be disposed of at a
tipping site licensed for the disposal of industrial waste. Protective clothing is not
required when handling these articles, but we recommend you follow the normal
hygiene rules of not smoking, eating or drinking in the work area and always wash
your hands before eating or drinking.
This appliance does not contain any component manufactured from asbestos or
asbestos related products.
FITTING THE CERAMIC COAL FUEL EFFECT
The ceramic fuel effect may cause staining / discolouration to decorative surfaces. It is
therefore advisable to protest decorative surfaces.
Note: Depending upon model the detail around the ceramic fuel effect may be different
to that shown.
1.
Place the ceramic base coal in the burner compartment. The bottom rear face of the
coal should rest on the
angled ledges at the back
of the burner
compartment. The
bottom front recess
edges on the coal base
should locate against the
tags at the front of the
ceramic support (See
figure 1).
Page 2
INSTALLER AND OWNER GUIDE
Figure 1. Ceramic base location

2. Place the left-hand ceramic front coal
in position in front of the base coal. The
front of the ceramic coal should touch the
front of the burner module (See figure 2).
3. Place the right hand ceramic front coal
in position in front of the base coal. This
should overlap the left-hand coal. Push
the two sides together to minimise the
gap. The front of the ceramic coal should
touch the front of the burner module (See
figure 2).
4. It is important that the front ceramics
are positioned correctly and do not cover
the burner ports in any way (See figure
2).
Install the 12 loose coals as follows. The
underside of each coal is marked with a
letter ‘A’ to ‘L’ and an arrow.
The coals should be positioned so that the
arrows always point towards the back of the firebox. When located into position the
stem of each arrow should be at 90° to the rear of the firebox.
5. Hold coal ‘A’ upright with the arrow
pointing to the top. Locate coal ‘A’ as
shown in figure 3.
INSTALLER AND OWNER GUIDE
Page
3
Figure 3. Front row “Coal A”
Figure 2. Front coal location

Locate coals ‘B’ to ‘E’ so that they are firmly seated in the valleys in the coal base and
front coal.
6. Hold coal ‘B’ upright
with the arrow pointing
to the top. Locate coal
‘B’ as shown in figure 4.
7. Hold coal ‘C’ upright
with the arrow pointing
to the top. Locate coal
‘C’ as shown in figure 5.
8. Hold coal ‘D’ upright
with the arrow pointing
to the top. Locate coal
‘D’ as shown in figure 6.
Page 4
INSTALLER AND OWNER GUIDE
Figure 6. Second row “Coal D”
Figure 5. Second row “Coal C”
Figure 4. Second row “Coal B”

9. Hold coal ‘E’ upright
with the arrow pointing
to the top. Locate coal
‘E’ as shown in figure 7.
10. Hold coal ‘F’ upright
with the arrow pointing
to the top. Locate coal
‘F’ as shown in figure 8.
This will complete the second row of loose coals.
Locate coals ‘G’ to ‘K’ so that they are firmly seated in the valleys in the coal base.
11. Hold coal ‘G’
upright with the arrow
pointing to the top.
Locate coal ‘G’ as
shown in figure 9.
INSTALLER AND OWNER GUIDE
Page
5
Figure 7. Second row “Coal E”
Figure 8. Second row “Coal F”
Figure 9. Third row “Coal G”

12. Hold coal ‘H’
upright with the arrow
pointing to the top.
Locate coal ‘H’ as
shown in figure 10.
13. Hold coal ‘I’ upright
with the arrow pointing
to the top. Locate coal
‘I’ as shown in figure 11.
14. Hold coal ‘J’ upright
with the arrow pointing
to the top. Locate coal
‘J’ as shown in figure 12
Page 6
INSTALLER AND OWNER GUIDE
Figure 12. Third row “Coal J”
Figure 10. Third row “Coal H”
Figure 11. Third row “Coal I”

15. Hold coal ‘K’
upright with the arrow
pointing to the top.
Locate coal ‘K’ as
shown in figure 13.
16. Hold coal ‘L’ upright
with the arrow pointing
to the top. Locate coal
‘L’ as shown in figure
14.
INSTALLER AND OWNER GUIDE
Page
7
Figure 13. Third row “Coal K”
Figure 14. Third row “Coal L”