baxter DOSEEDGE User instructions

Setting Up the PrepStation Cart
M00205 v1.1

Table of Contents
SETTING UP THE PREPSTATION CART
M00205 v1.1
TABLE OF CONTENTS
UNPACKING THE PREPSTATION CART AND COMPONENTS....................................................... 1
SETTING UP THE CART.............................................................................................................. 2
SETTING UP THE TOUCHSCREEN AND CABLES .......................................................................... 3
SETTING UP THE PRINTER ........................................................................................................ 6
Setting Up the Zebra Printer............................................................................................... 6
Setting Up the Epson Printer .............................................................................................. 7
SETTING UP THE OTHER COMPONENTS ................................................................................... 8

Unpacking the PrepStation Cart and Components
SETTING UP THE PREPSTATION CART
M00205 v1.1 Page 1
UNPACKING THE PREPSTATION CART AND COMPONENTS
1. Remove all parts from the carton.
NOTE: The cable guide is not shown.
2. Unpack all components, power cables and connecting cables:
•Uninterruptible power supply (UPS)
•Touchscreen monitor and cables
•Label printer and cables
•Barcode scanner
•Foot pedal (optional)
•Scale (optional)

Setting Up the PrepStation Cart
SETTING UP THE PREPSTATION CART
M00205 v1.1 Page 2
SETTING UP THE CART
1. Remove the cover
from the box at the
base of the cart.
2. Insert the UPS in
the rear
compartment of
the box. Thread the
power cable
through the hole in
the base.
3. Do not replace the
cover on the box
yet. Do not plug in
the UPS.
4. Set the platform on
the base so the
screw holes are
aligned.
5. From below, insert
and tighten 5
screws.

Setting Up the Touchscreen and Cables
SETTING UP THE PREPSTATION CART
M00205 v1.1 Page 3
SETTING UP THE TOUCHSCREEN AND CABLES
1. Align the touchscreen supports
with its brace on the cart.
Insert and tighten 4 screws.
Tip! Install the top screws first.
2. Place the power supply units
for all components in the front
compartment of the power
box.
3. Plug each power cord into the
UPS.
4. Thread the cords through the
whole in the bottom of the
power box.
Tip! Make sure the cables are
untangled and unimpeded.

Setting Up the Touchscreen and Cables
SETTING UP THE PREPSTATION CART
M00205 v1.1 Page 4
5. Insert the cable guide in the
top of the tower until it pokes
out the bottom.
6. Snag the cords with the cable
guide.
Tip! Pull all cords together at
one time. Pulling the cords
individually is more difficult.

Setting Up the Touchscreen and Cables
SETTING UP THE PREPSTATION CART
M00205 v1.1 Page 5
7. Draw the cable guide through
the tower until the cords are
amply threaded through the
opening.
Tip! It is better to have too
much available cord than too
little.
8. Tilt the touch-screen up.
Connect the power cord or USB
cable (depending on model) to
the monitor. Make sure the
cord hangs loosely.
Tip! Push any excess cable in
the hole on the upright, but
not so much that the cords are
pulled tight when the monitor
is tilted up. The cables should
be slack, but not messy.
CAUTION!
Taut cables can snap
when the touchscreen
is raised.

Setting Up the Printer
SETTING UP THE PREPSTATION CART
M00205 v1.1 Page 6
SETTING UP THE PRINTER
SETTING UP THE ZEBRA PRINTER
1. Place the printer on the
platform. Connect the power
cord (threaded through the
post) to the printer.
2. Connect the USB or parallel
cable (depending on model)
to the printer, and then to the
touchscreen.

Setting Up the Printer
SETTING UP THE PREPSTATION CART
M00205 v1.1 Page 7
SETTING UP THE EPSON PRINTER
1. Place the printer on the
platform. Connect the power
cord (threaded through the
post) to the printer.
2. Connect the cable to the
printer, and then to the
touchscreen.

Setting Up the Other Components
SETTING UP THE PREPSTATION CART
M00205 v1.1 Page 8
SETTING UP THE OTHER COMPONENTS
1. Connect the scanner to the
touchscreen.
2. Place the scanner in its
holder, then position the
scanner in the hood.

Setting Up the Other Components
SETTING UP THE PREPSTATION CART
M00205 v1.1 Page 9
3. Connect the camera stand
cable to the touchscreen.
4. Install the lens on the camera.
Attach the camera to the
camera stand.

Setting Up the Other Components
SETTING UP THE PREPSTATION CART
M00205 v1.1 Page 10
5. Connect the cable to the
camera. Position the camera
and stand in the hood.
6. Connect the footpedal
(optional) to the touchscreen.
Position the footpedal where
desired.
7. Optional: Connect the power
cord to the scale, then
connect the USB cable from
the scale to the touchscreen.
Refer to the installation
instructions for the scale.
8. Connect the ethernet cable
from the wall outlet to the
touchscreen.

Setting Up the Other Components
SETTING UP THE PREPSTATION CART
M00205 v1.1 Page 11
9. Replace the cover on the box.
10. Roll the cart into position.

Error! Reference source not found.
Baxter and DoseEdge are trademarks of Baxter International Inc. or its subsidiaries. All other trademarks, brands or
product images appearing herein are the property of their respective owners.