baxter DUPLOSPRAY Service manual

DUPLOSPRAY Quick Reference Guide (laparoscopic procedures)
Position DUPLOSPRAY System so the foot
pedal is placed next to the surgeon’s foot
at time of application.
Instructions for Circulating Nurse |DUPLOSPRAY MIS Regulator
Attach gas supply hose, located at back of
regulator, to source of medical grade CO2.
21
Instructions for Scrub Nurse |DUPLOSPRAY MIS Applicator
Attach patient vent line (red luer connector)
to available female luer on trocar vent valve.
Ensure vent valve is fully open.
6
Pass assembled double syringe and spray
applicator to surgeon for spray application.
5
Attach gas supply line (clear luer connector)
to sterile applicator. Turn white locking
collar to secure connection.
4
Fasten the pull strap to the double
syringe holder to assure the spray
applicator is tightly secured.
3
Firmly attach the applicator to the
nozzles of the double syringe.
2
Thread sterile replaceable tip onto
applicator using tip alignment tool.
1
Instructions for Surgeon
While activating foot pedal dispense
TISSEEL Fibrin Sealant through applicator
tip by depressing double syringe plungers
using very slow, steady pressure. To stop
spray delivery release pressure on plungers
while maintaining gas flow by holding
down foot pedal for an additional 3-5
seconds to clear applicator tip.
3
TIPS
• The patient vent line attached to the trocar cannula vent valve will only vent gas out when foot pedal is depressed.
After connection to trocar cannula, ensure vent valve is fully open on trocar cannula prior to spray application.
• If tip becomes occluded during use, remove plugged tip by unscrewing it counterclockwise. Using a sterile cloth,
wipe any clotted material off exposed tube ends. Screw on new tip and tighten with finger pressure.
• The twin-tube assembly can be easily separated as necessary to allow freedom of movement.
For full prescribing information about Tisseel, contact your local sales representative
The use of TISSEEL Fibrin Sealant is restricted to experienced surgeons who have been trained in the use of TISSEEL.
In order to ensure optimal safe use of TISSEEL by spray application, apply a minimum spray distance of 2 cm and a maximum spray
pressure of 1.5 bar (22 psi/maximum gas flow rate 2.0 liters per minute) to minimize the potential risk of air or gas embolism, tissue
rupture, or air or gas entrapment with compression.
While depressing foot pedal, adjust gas
flow rate to 1.0-2.0 liters per minute.
Check gas flow by noting height of ball in
flow gauge while stepping on foot pedal.
4
Attach spray set to regulator. Connect the
blue vent line filter to the blue female luer
and the clear gas line filter to the male
luer on the regulator.
3
Depress foot pedal to start gas flow prior
to applying TISSEEL Fibrin Sealant. Check
gas flow gauge on regulator before
inserting applicator. If flow level ball does
not move when foot pedal is depressed,
the applicator tip is occluded and should
be replaced.
2
Confirm actual flow of max 2 liters/min
with OR personnel.
1

DUPLOSPRAY Quick Reference Guide
Connect to regulated CO2gas source only; maximum input pressure not to exceed 100 psi ± 5 (6.89 bar ± .35). To avoid possible air or gas embolism, do not directly
spray into circulatory pathways.
Caution: Any application of pressurized gas may be associated with a potential risk of air or gas embolus, tissue rupture or air or gas entrapment with compression,
which may be life threatening. Be sure to take appropriate measures to address these risks by observing the recommended minimum spraying distance of 2 cm (optimal
working distance 3 cm) and the maximal flow rate of 2.0 standard liters per minute.
For detailed information please contact your local representative
In some countries TISSEEL Fibrin Sealant is licensed under the trademark of TISSUCOL Fibrin Sealant.
Baxter, Tisseel, Tissucol, and Duplospray are trademarks of Baxter International Inc., its subsidiaries or affiliates.
BEMP/90/15-0003 date of creation/review: may 2015
Baxter Belgium SPRL
bd d’Angleterre, 2-4
1420 Braine l’Alleud
In order to ensure optimal safe use of TISSEEL by spray application the following recommendations should be followed:
Recommended pressure, distance and devices for spray application of TISSEEL
Surgery Spray set to be used Applicator tips to be used Pressure regulator to be used Recommended distance
from target tissue
Recommended spray
pressure / gas ow rate
Laparoscopic/ minimally
invasive procedures n.a.
DUPLOSPRAY MIS Applicator
20cm
DUPLOSPRAY MIS Regulator
2 – 5 cm 1.2-1.5 bar (18-22psi) /
1.0-2.0 L/min
DUPLOSPRAY MIS Regulator NIST B11
DUPLOSPRAY MIS Applicator
30cm
DUPLOSPRAY MIS Regulator
DUPLOSPRAY MIS Regulator NIST B11
DUPLOSPRAY MIS Applicator
40cm
DUPLOSPRAY MIS Regulator
DUPLOSPRAY MIS Regulator NIST B11
Replaceable tip
DUPLOSPRAY MIS Regulator
DUPLOSPRAY MIS Regulator NIST B11
When spraying the TISSEEL, changes in blood pressure, pulse, oxygen saturation and end tidal CO2should be monitored because of the possibility of occurrence of air or gas embolism.
Any application of pressurized gas may be associated with a potential risk of air or gas embolism, tissue rupture or air or gas entrapment with
compression, which may be life threatening if the product is sprayed incorrectly
Precautions
For TISSEEL/TISSUCOL Fibrin Sealant
• Spray application should only be used if it is possible to accurately judge the spray distance as recommended by the manufacturer. Do not spray closer than the
recommended distances.
• Prior to applying sprayable fibrin solutions for sealant, the surface area of the wound should only be dried using standard techniques (eg, intermittent application of
compresses, swabs, use of suction devices).
• Blood pressure, pulse rate, oxygen saturation and end tidal CO2should be monitored closely when spraying fibrin solutions for sealant using a pressure regulator
device, because of the possibility of occurrence of air or gas embolism.
• Regulators should be used in line with manufacturer recommendations and the SmPC and Instruction for Use.
• In laparoscopic procedures: Use CO2only when using spray application. When applying the product as a spray using a CO2pressure regulator device, the maximum
pressure should be 1.5 bar (22 psi/maximum gas flow rate 2.0 liters per minute). The product should be sprayed at a distance at least 2 cm (recommended range
2-5 cm) from the tissue surface.
CAUTION BOX