beevision 182S User manual
Version 1.2.2
1
CONTENTS
1. Preface ........................................................................................... 2
2. Description of The Product and Intended Use ........................... 4
3. Installation ...................................................................................... 5
2
1. Preface
This document describes the installation of the BeeVision 182S
dimensioning system. Permission must be obtained from 3DTİM
Elektronik A.Ş. (3DTIM) to copy, reprint and translate this document in
whole or in part. This manual may not be published, in whole or in part, or
used without authorization for competitive purposes. 3DTIM reserves
the right to make technical changes for improvement.
BeeVision 182S can only be used for dimensioning measurements of
opaque objects with a maximum size of 500 x 400 x 400 mm (WxLxH).
Any use other than this purpose is deemed illegal and constitutes a
misuse of the machine. If it is used in this way, all responsibility will be on
the user.
BeeVision 182S is under warranty for 1 year. Malfunctions resulting
from user error or the use of the device not in accordance with the user
manual are not covered by the warranty.
T
his
installation
requires
15
minutes and
1
pe
rson
.
3
Figure 1.1
4
This device must be used in accordance with the
restrictions stated above.
2. Description of The Product
and Intended Use
BeeVision 182S is an industrial product used for dimensioning
and weighing. It is designed for dimensioning and weight measurements
of 500 x 400 x 400mm (WxLxH) opaque objects with a maximum
weight of 60 kg.
2.1 Important Information
If the upright column is damaged, or the measuring unit angle is
distorted, the device may not work properly. Make sure the
measuring unit is flat with respect to the measurement surface.
You may use a water level to ensure that.
BeeVision 182S cannot measure transparent objects such as
glass or nylon.
This device must be used in accordance with the restrictions
stated above.
5
3. Installation
BeeVision 182S is shipped as 2 boxes. The weight of Box-1 is 20 kg,
dimensions are 1015 x 520 x 280 mm as shown in Figure 3.1. The weight
of Box-2 is 19 kg, dimensions are 675 x 745 x 205 mm.
Figure 3.1
6
Step 1
Make sure all 9 parts indicated in Figure 3.2 are present in the boxes.
Carefully remove the BeeVision 182S components from the boxes.
Figure 3.2
Scale
Barcode Reader
Top Column
Base
Column
Measuring Unit
Monitor
Screwdriver
Power Adapter Boxes
7
Step 2
Put together the upper group and the bottom group as shown in Figure
3.3 using the 4 bolts provided on the device.
Figure 3.3
8
Step 3
Loosely screw in the bolts on to the Measuring Unit. Pay attention that
the bolts are not tight because the measuring unit will slide in the slot.
Connect the cables coming out of the top column to the relevant
connectors shown in Figure 3.4 on the measuring unit. Mount the
measuring unit by inserting the bolts into the slots and slide the device
down as shown in Figure 3.5. Then you have to use the screwdriver from
Box 1 as shown Figure 3.6 to tighten the bolts.
Figure 3.4
Figure 3.5
Figure 3.6
9
Step 4
Mount the monitor to the base column with the help of 4 bolts provided
on the monitor as shown in Figure 3.7. After that, connect the monitor
cables coming out of the holes on both sides of the base column to the
monitor.
Figure 3.7
10
Step 5
To assemble the scale, use 2 bolts provided on the base plate as shown in
Figure 3.8.
Figure 3.8
11
Step 6
Connect the RS-232 cable of the scale to the connector shown in the
Figure 3.9.
Figure 3.9
12
Step 7
The power adapter and its cables are provided in Box-1. Connect the
cables to the power adapter and connect the other end of the cable to
the power input on the backside of the device shown in Figure 3.10.
Figure 3.10
13
Step 8
To use the barcode reader, connect the USB cable of the barcode reader
to the connector on the backside of the device shown in Figure 3.11.
Figure 3.11
14
Step 9
You have completed the installation of BeeVision 182S. Congrats!
Figure 3.12
15
Thank you for joining our family!
16
For more information, please contact us.
Website: www.beevision.ai
Mail: [email protected]
Phone : +90 534 401 85 89
Follow us to keep up with the updates.
BeeVision
BeeVision
@beevisiondimensioner
@beevision_ai
For online Installation Manual:
Other beevision Measuring Instrument manuals
