Behringer ULM200M User manual

ULM200M /ULM200D Controls
ULM200M /ULM200D Controls
1. POWER/STATUS LED
1. ▼ VOLUME Button (Mute/volume down)
2. ▲ VOLUME Button (Power on/unmute/volume up)
3. USB connector
5. Wireless Link Status LED
ULM200M /ULM200D Getting Started
1.Connect the ULM200D wireless receiver to the “WIRELESS ONLY!”USB connector on
wireless-enabled BEHRIINGER mixers, powered speakers or other compatible products, or to a
USB port on a computer.
2.Press and hold the ▲ button on the ULM200M wireless microphone to connect wirelessly to the
ULM200D receiver. The LED on the microphone will fl ash slowly during the connecting
sequence and will light solid once connected. If the ULM200M wireless microphone cannot
connect to a receiver, the microphone will automatically power down after 10 seconds.
3.Once connected, the ULM200M microphone will be set at a medium volume. Use the ▲ and ▼
buttons to adjust the volume
4. A long press of the ▼ button will put the ULM200M microphone into mute. The mute
condition is indicated by rapid fl ashing of the LED. If the user does not unmute within 60
seconds, the ULM200M microphone will power down to save battery life.
5. A short press of the ▲button will unmute the ULM200M microphone. If the ULM200M
microphone is unmuted more than 10 seconds after muting, it will return to the previous volume
level, if unmuted after less than 10 seconds it will be set to the minimum volume level.
6. Unplug the ULM200D wireless receiver to power down. The ULM200M wireless microphone

will power down 10 seconds after the ULM200D wireless receiver is unplugged.
7. The LED in the ULM200M wireless microphone will indicate when the battery is low by
regular brief fl ashes.
8. Should the ULM200M wireless microphone become unpaired with the ULM200D wireless
receiver, the microphone can be re-paired from the powered down state by simultaneously
pressing the ▲ and ▼ buttons and moving the microphone to within 10 cm (4 inches) of the
ULM200D wireless receiver. The LED on the microphone will fl ash slowly during the pairing
sequence and will light solid once connected. If the ULM200M wireless microphone cannot pair
to the receiver it will automatically power down after 10 seconds.
Specification
RF output <100 mW / +20 dBm
Operating range 120 m (Line of Sight)*
Dynamic range 92 dB, A-weighted**
Equivalent input noise -112 dBu
Frequency Response 20 Hz - 20 kHz, ±1 dB
(Wireless Link)
Sampling rate 48 kHz
Resolution 24-bit
Encoding 232 kbps SLAC
(Slightly Lossy Audio Codec)
Latency 14.5 ms
RF frequency 2.4 GHz ISM band
(2406 MHz - 2474 MHz)
18 channels
Power Supply current 70 mA @ +5 VDC
Battery type 2 x AA (LR6) Alkaline cells
Battery life >30 hours
Dimensions (W x D x H) 45.7 x 45.7 x 243.8 mm
(1.8 x 1.8 x 9.6")
Weight 0.4 kg (0.9 lbs)*
Achievable range will be dependent on nearby sources of RF interference and/or line of sight
obstacles.**Measured from analog input to analog output, unity gain operation without
LEGAL DISCLAIMERMUSIC
Group accepts no liability for any loss which may be suff ered by any person who relies either
wholly or in part upon any description, photograph, or statement contained herein. Technical
specifi cations, appearances and other information are subject to change without notice. All
trademarks are the property of their respective owners. MIDAS, KLARK TEKNIK,
TURBOSOUND, BEHRINGER, BUGERA and DDA are trademarks or registered trademarks of
MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2014 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding MUSIC

Group’s Limited Warranty, please see complete details online at music-group.com/warranty.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
Responsible Party Name: MUSIC Group Services NV Inc.
Address: 5270 Procyon Street Las Vegas, NV 89118 USA
Phone Number: [phone]
ULTRALINK ULM200M/ULM202D
complies with the FCC rules as mentioned in the following paragraph:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and receiver
•Connect the equipment into an outlet on a circuit diff erent from that to which the receiver is
connected
•Consult the dealer or an experienced radio/TV technician for help
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Important information:
Changes or modifi cations to the equipment not expressly approved by MUSIC Group can void
the user’s authority to use the equipment.
Operation in the 2.4 GHz ISM (Industrial, Scientifi c, Medical) frequency band may be subject to
interference from other transmitting equipment operating in this band. In the event of such
interference, please verify and reassign the transmitting channels of any potentially interfering
transmitting equipment.
RF EXPOSURE (USB Receiver):
The USB Receiver is intended to use exclusively with Behringer mobile host devices as indicated
in the user manual, it is not intended to connect to laptops or computers.
A distance of 20 cm shall be maintained between the antenna and users, and the transmitter may
not be co-located with any other transmitter or antenna.