Behringer 2500 Series User manual

Quick Start Guide
DUAL NOISE / RANDOM
VOLTAGE GENERATOR
MODULE 1016
Legendary 2500 Series Dual Noise
Source Module for Eurorack
Controls
(1) LEDs – Indicate whether the associated knob is active.
(2) NOISE knob – Attenuates the output of the noise
generator.
(3) SLOW RANDOM knob – Attenuates the output of the
slow random voltage generator.
(4) WHITE/PINK/OFF switch – Selects between white or
pink noise, or disengage the output.
(5) OFF/ON switch – Engages or disengages the slow
random voltage output.
(6) NOISE A/B – Send the noise A and B signals to other
modules via 3.5 mm TS cable.
(7) RANDOM A/B – Send the random voltage signals to other
modules via 3.5 mm TS cable.
Power Connection
The unit comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make
these connections before the module has been mounted into
a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
(1)
(2)
(3)
(4)
(5)
(6) (7)
V 1.0

Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of xed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded
plate. Attach the screws part way to start, which will allow
small adjustments to the positioning while you get them all
aligned. After the nal position has been established, tighten the
screws down.
Specications
Outputs
Noise
Type 2 x 3.5 mm TS jacks,
DC coupled
Impedance 1 kΩ, unbalanced
Max output level ±5 V
Random
Type 2 x 3.5 mm TS jacks,
DC coupled
Impedance 1 kΩ, unbalanced
Max output level ±5 V
Controls
Noise Attenuates noise
generator output
Random Attenuates voltage output
White/pink/o Selects white or pink noise,
or o
Random on/o Engages or disengages
voltage generator
Power
Power supply Eurorack
Current draw 45 mA (+12 V),
15 mA (-12 V)
Physical
Dimensions 42 x 71 x 129 mm
(1.7 x 2.8 x 5.1")
Rack units 14 HP
Weight 0.13 kg (0.29 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and
other information are subject to change without notice. All trademarks are the
property of their respective owners. Midas, KlarkTeknik, Lab Gruppen, Lake,
Tannoy,Turbosound, TC Electronic,TC Helicon, Behringer, Bugera, Auratone
and Coolaudio are trademarks or registered trademarks of MusicTribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2020 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding MusicTribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.