Beko HCA62541B User manual

Hood
User manual
HCA62541W HCA62541BH
HCA62541B
01M-8851153200-3820-13
01M-8851163200-3820-13
01M-8865223200-3820-13
EN PL RO DE ES FR NL
CS SL SK UA ET LT LV

This product has been manufactured in environmental friendly modern plants without giving any harm to the nature.
This appliance conforms to the WEEE regulation. It does not contain PCB.
Please read this user manual first!
Dear Customers!
Thank you for preferring a Beko product. We hope that you get the best results from
your product which has been manufactured with high quality and state-of-the-art
technology. Therefore, please read this entire user manual and all other accompanying
documents carefully before using the product and keep it as a reference for future use.
If you handover the product to someone else, give the user manual as well. Follow all
warnings and information in the user manual.
Rememberthatthisuser manualis alsoapplicable for severalothermodels. Differences
between the models are explicitly described in the manual.
Meanings of the Symbols
Following symbols are used in the various section of this manual:
C
Important information or useful hints about
usage.
A
WARNING: Warnings for dangerous situations
concerning the safety of life and property.
B
Warning for electric shock.
Warning for hot surfaces.
Lamp

3 / EN
Hood / User Manual
CONTENTS
ENGLISH 04-22
POLSKI 23-42
ROMÂNĂ 43-61
DEUTSCH 62-83
ESPAÑOL 84-105
FRANÇAIS 106-126
NEDERLANDS 127-148
ČESKY 149-167
SLOVENŠČINA 168-187
SLOVENSKÝ 188-207
УКРАЇНСЬКИЙ 208-228
EESTI 229-248
LIETUVIŲ K. 249-268
LATVISKI 269-288

4 / EN Hood / User Manual
1.1 General Safety
Important Safety Instructions Read
Carefully And Keep For Future Refe-
rence This section contains safety
instructions that will help protect
from risk of fire, electric shock,
exposure to leak microwave energy,
personal injury or property damage.
Failure to follow these instructions
shall void any warranty.
• Beko products comply with the
applicable safety standards; the-
refore, in case of any damage on
the appliance or power cable, it
should be repaired or replaced
by the dealer, service center or a
specialist and authorized service
alike to avoid any danger. Faulty
or unqualified repair work may be
dangerous and cause risk to the
user.
• This appliance is intended to be
used in household and similar ap-
plications such as:
– Staff kitchen areas in shops, of-
fices and other working environ-
ments;
– Farm houses
– By clients in hotels, and other re-
sidential type environments;
– Bed and Breakfast type environ-
ments.
• Operate the appliance for its in-
tended purpose only as described
in this manual.
• The manufacturer cannot be held
liable for damages resulting from
improper installation or misuse of
the product.
• This appliance can be used by chil-
dren aged from 8 years and above
and persons with reduced physi-
cal, sensory or mental capabilities
or lack of experience and know-
ledge if they have been given
supervision or instruction concer-
ning use of the appliance in a safe
way and understand the hazards
involved.
• Children shall not be allowed play
with the appliance. Cleaning and
user maintenance shall not be
made by children without super-
vision.
• The minimum distance between
the supporting surface for the co-
oking vessels on the hob and the
lowest part of your product must
be at least 65 cm.
• If the instructions for installation
for the gas hob specify a greater
distance, this has to be taken into
account.
• Make sure that your mains power
1 Important safety and environmental instructions

5 / EN
Hood / User Manual
supply complies with the informa-
tion supplied on the rating plate of
the appliance.
• Never use the appliance if the
power cable or the appliance itself
is damaged.
• Prevent damage to the power
cable by not squeezing, bending,
or rubbing it on sharp edges. Keep
the power cable away from hot
surfaces and naked flame.
• Use the appliance with a groun-
ded outlet only.
WARNING: Do not connect the ap-
pliance to the mains until the instal-
lation is fully complete.
• Place the appliance in a way so
that the plug is always accessible.
• Do not touch the lamps if they
have operated for a long time.
They can burn your hands since
they will be hot.
• Follow the regulations set out
by competent authorities on di-
scharge of the exhaust air (this
warning is not applicable for use
without Chimney ).
• Operate your appliance after put-
ting a pot, pan etc. on the hob.
Otherwise, high heat may cause
deformation in some parts of your
product.
• Turn off the hob before taking the
pot, pan etc. from it.
• Do not leave hot oil on the hob.
Pans with hot oil may cause self
combustion.
• Pay attention to your curtains
and covers since oil may catch fire
while cooking food such as fries.
• Grease filter must be replaced at
least monthly. Carbon filter must
be replaced at least every 3 mon-
ths.
• Product shall be cleaned ac-
cordance with user manual. If
cleaning was not carried out in ac-
cordance with user manual, there
may be fire risk.
• Do not use non-fire-resistant fil-
tering materials instead of the
current filter.
• Only use the original parts or parts
recommended by the manufactu-
rer.
• Do not operate the product wi-
thout the filter and do not remove
the filters while the product is
running.
• In the event of be started any
flame, de-energize your product
and cooking appliances.
• In the event of be started any
flame, cover the flame and never
1 Important safety and environmental instructions

6 / EN Hood / User Manual
use water to extinguish.
• Unplug the appliance before each
cleaning and when the appliance
is not in use.
• The negative pressure in the envi-
ronment should not exceed 4 Pa
(4 x 10 bar) while the hood for
electric hob and appliances run-
ning on another type of energy
but electricity operate simultane-
ously.
• In the environment where the ap-
pliance is being used, the exhaust
of devices running on fuel oil or
gas, such as room heater must be
absolutely isolated or device must
be hermetical type.
• When connecting the Chimney ,
use pipes with a diameter of 120
or 150 mm. Pipe connection must
be as short as possible and have
as few elbows as possible.
Danger of choking! Keep all the
packaging materials away from chil-
dren.
CAUTION: Accessible parts may be-
come hot when used with cooking
appliances.
• The product outlet must not be
connected to air channels that in-
clude other smoke.
• The ventilation in the room may
be insufficient when the hood for
electric hob is used simultane-
ously with the devices operating
on gas or other fuels (this may
not apply to appliances that only
discharge the air back into the
room).
• Objects placed on the product may
fall. Do not place any objects on
the product.
• Do not flambe under the your pro-
duct.
WARNING: Before installing the
Hood, remove the protective films.
• Never leave high naked flames
under the hood when it is in ope-
ration
• Deep fat fryers must be continu-
ously monitored during use: over-
heated oil can burst into flames.
1.2 Compliance with the WEEE
Directive and Disposing of the
Waste Product:
This product complies with EU
WEEE Directive (2012/19/EU). This
product bears a classification
symbol for waste electrcal and
electronc equpment (WEEE).
Ths symbol ndcates that
ths product shall not be
dsposed wth other house-
1 Important safety and environmental instructions

7 / EN
Hood / User Manual
hold wastes at the end of ts servce
lfe. Used devce must be returned
to offcal collecton pont for recy-
clng of electrcal and electronc de-
vces. To fnd these collecton
systems please contact to your lo-
cal authortes or retaler where the
product was puchased. Each hou-
sehold performs mportant role
n recoverng and recyclng of old
applance. Approprate dsposal of
used applance helps prevent po-
tental negatve consequences for
the envronment and human he-
alth.
1.3 Complance wth RoHS
Drectve
The product you have purchased
comples wth EU RoHS Drectve
(2011/65/EU). It does not contan
harmful and prohbted materals
specfed n the Drectve.
1.4 Package Informaton
Packagng materals of the
product are manufactured
from recyclable materals n
accordance wth our Natonal
Envronment Regulatons. Do not
dspose of the packagng materals
together wth the domestc or ot-
her wastes. Take them to the pac-
kagng materal collecton ponts
desgnated by the local authortes.
1 Important safety and environmental instructions

8 / EN Hood / User Manual
2 General Appearance
Technical data contained in this manual and
labels attached to the hood were obtained from
measurements and calculations in accordance
with the requirements of EU Regulation No.
65/2014 and 66/2014. This appliance complies
with the European Directives 2009/125/EC and
2011/65/EU.
Fig.1 Dimension drawing
2.1 Technical Data
Model HCA 62541 W / HCA 62541 B/ HCA62541BH
Supply voltage 220-240V ~ 50 Hz
Lamp Power 6 W
Motor Power 200 W
Flow rate (m³/h) – 3. Level 365 m/h
Insulation Class of Motor Class F
Insulation Class Class I

9 / EN
Hood / User Manual
2 General Appearance
1
3
5
2
4
6
Fig.2 Explanatory figure of the kitchen hood
1. Chimney cover
2. Power supply cord
3. Hinged flap
4. Touch control panel
5. Aluminium grease filter
6. Lighting

10 / EN Hood / User Manual
3 Operation of the Appliance
The hood is designed for suction of fumes while
preparing meals. The device can be operated in
two modes:
As extractor: vapors are removed outside the
room by means of a venting pipe. The venting
pipe is not available with the device and must be
purchased separately.
A
Use the shortest vapor discharging
pipe possible.
A
The venting pipe shall have the
smoothestinner surfaceaspossible
(it is not recommended to use pipes
of type spiro).
A
Use a pipe with as few bends as
possible (bending angles should
not be greater than 90 degrees).
A
It is not recommended to apply
section changes of the pipe (larger
to smaller e.g. air outlet Ø150 mm
to air outlet Ø120mm).
As absorber: vapors are cleaned of grease and
odors before they are returned to the room
through the grille on the upper chimney cover. If
the hood shall work as an absorber, it is necessary
to install an active carbon filter (Fig. 6). The
carbon filter is not standard equipment; it must be
purchased from a vendor.
The hood is equipped with a touch control located
on the top glass panel (Fig.3).
Fig. 3 Localization of the touch panel
Designation of touch fields:
Switching on/ off the hood
Switching on/ off the hood lighting
Reduction of turbine speed
Increasing the turbine speed
Digital display

11 / EN
Hood / User Manual
3.1 Control of turbine
operation
In standby mode, the control panel is not
illuminated and the fields , and are
disabled. To activate the control panel, touch the
field or use the remote control (if enclosed).
After activation, the control panel is highlighted
and the touch field symbols appear; touching the
field starts the turbine at the recently used
gear, touching the field starts the turbine
at the highest gear and touching the field
starts the turbine at the lowest gear. The turbine
speed can be increased by touching the field ,
reducing - by touching the symbol . Disabling
the hood turbine is done by touching the field
or after touching the field when the turbine
is operating at first gear. Along with the change
of turbine speed, the digits on the display change
accordingly:
1- turbine operating in first gear, 2- turbine
operating in second gear, 3- turbine operating in
third gear, 4- turbine operating in intensive gear
(turbo).
In accordance with EU regulation 66/2014, the hood
is equipped with an automatic, five-minute counter,
which automatically changes the turbine level from
fourth gear into third after 5 minutes (does not
apply to the model with turbine number “5”).
3.2 Lighting control
To turn on the hood light, the symbol must be
pressed; another pressing of the symbol switches
the light off.
3 Operation of the Appliance
3.3 Additional information on
the hood control
The hood control is equipped with a hood
operation counter. The counter is set to 35 hours.
After this time expires, the display shows the
symbol indicating the recommended cleaning
of the aluminum filter. To delete the symbol
“F” on the hood display, the symbol must
be touched and held continuously for about 8
seconds.
The hood control is equipped with a touch panel
lock to deactivate the touch panel, for example
when cleaning the hood. To enable the lock, touch
and hold the symbol (for about 10 seconds)
until the symbol (dot in the lower right corner)
appears on the display. To return to normal
operation, touch and hold the symbol again
(for about 10 seconds) until the dot on the display
goes out. The hood control is equipped with a
time switch that disables the hood turbine after
15 minutes from the switching on of the counter.
The time switch of the turbine does not disable
the lighting and the speed of the turbine can be
freely changed. To activate the time switch, the
hood turbine must work on any speed on the 1, 2,
3 or intense gear. The timer is activated by holding
the symbol (for about 10 seconds), until a dot
starts to flash in the lower right corner. To disable
this feature, hold again the symbol (for about 10
seconds) or turn the hood off.
The hood control is equipped with a feature to
automatically turn off the turbine operation after
2 hours of inactivity of hood control.

12 / EN Hood / User Manual
3.4 Remote control operation
The turbine operation is
controlled with the upper part
of the remote control, marked
as . Enabling/ disabling the
turbine is done by pressing the
button with the symbol but also and
Inceasing speed is done by pressing the button
, reducing it by pressing the button .
3.5 Lightingcontrolviaremote
control
The lighting is controlled
with the bottom part of
the remote control,
marked as . Enabling/
disabling the light is done
by pressing the button
with the symbol . The
buttons and are disabled.
3.6 Methods of reducing the
effect of cooking process on
the environment
To reduce Energy consumption, cook with using
covers on kitchenware.
• Aluminum filters must be kept clean
(recommended length of aluminum filter
operation between cleanings is max. 35h of
3 Operation of the Appliance
The hood has a remote control (only selected models) (Fig. 4)
Fig. 4 Remote control
Upper part of remote
control Bottom part of remote control
hood operation).
• Take care of permeability of the ventilation
pipes.
• The operation level of the turbine when cooking
shall be always set to a minimum gear, which
will allow removing the fumes at the current
intensity of cooking
3.7 Replacing of lighting
Prior to any work related to the replacement of
lighting, be sure to unplug the power supply. If
the hood was previously enabled, you should wait
until the light bulbs are cooled, after which you
can proceed with the replacement. The process
of exchanging the bulbs is shown in Fig. 5.
A
Before replacing the light bulbs,
disconnect the power supply of the
hood.
A
Do not touch the light bulbs when
they are hot.
A
Be careful not to touch the replaced
light bulb directly with hands.

13 / EN
Hood / User Manual
Symbol
Symbol
Bulb installation
Bulb dismantling
3 Operation of the Appliance
Fig.5 Replacing the lighting
Max:3W

14 / EN Hood / User Manual
4 Cleaning and maintenance
Before carrying out any maintenance operations
on the appliance, remove the plug from the wall
outlet. The hood should be cleaned with mild
cleaning agents, do not use abrasives. Regular
maintenance ntly improves the performance and
durability of the hood. The hood should be cleaned
at least once a month or every 35 hours of hood
operation. To clean hood DO NOT USE ALCOHOL-
BASED AGENTS. Satin items (inox) should be
cleaned with special preparations for that purpose.
A
Failure to comply with the
provisions relating to cleaning of
the device and replacement of
filters may cause fire risks. It is
therefore recommended to comply
with the guidelines given herein.
The manufacturer is not lia- ble for
any damage to the engine or fires
caused by improper use.
4.1 Grease filter
The hood is equipped with an aluminum filter,
which retains the fat particles from cooking. The
ter can be removed by moving the locks in the
direction of the arrows (Fig. 6). The ter should be
washed by hand by immersing for 15 minutes in
water with dishwashing liquid at a temperature of
40-50°C. After 15 minutes, you can proceed with
washing and then rinsing. The ter must be dry
before being placed in the hood. The ter can also
be washed in a dishwasher. During the washing
procedure, the ter may discolor, however it does
not a ect its tering properties. If the ter is not
cleaned regularly, it reduces the performance of
the hood and could cause the risk of re. The ter
should be cleaned at least after each 35 hours of
hood operation.
4.2 Carbon filter
The hood can be ted with an active carbon ter.
The carbon filter is applied only in case the hood is
not connected to the vent pipe.
The filter should be placed on the turbine casing,
as shown in drawing (Fig. 6 ). The active carbon
filter should be replaced every 6 months.
A
Thecarbonfiltershallnotbewashed
nor regenerated.
Fig.6 Replacing the carbon filter

15 / EN
Hood / User Manual
5 Installing your appliance
A
WARNING!
Before starting the installation,
read the safety information on
User Manual.
A
WARNING!
Failure to install with screws and
stabilizers in accordance with these
instructions may result in electric
shock.
The minimum distance of hood suspension
between the surface, on which the kitchenware
are positioned on the heating device (gas or
electric cooker), and the lowest part of the kitchen
hood (Fig. 7) must be not less than 65 cm.
If the instruction manual of the heating device
contains the requirement of a greater installation
distance of the kitchen hood than indicated above,
please follow these instructions. The installation
of the hood and the hood chimney shield is shown
in the drawings (Fig. 8 - Fig. 13)
The hood is equipped with mounting anchors
suitable for the majority of the walls and ceilings.
Thegeneralprovisionson the dischargeofair from
rooms have to be observed during installation.

16 / EN Hood / User Manual
5 Installing your appliance
5.1 Installation Accessories
1. Hood
2. Chimney
3. User Manual
4. Blower flaps
5. Ø150/120mm Plastic Adapter
6. 6x HS4,0 x45 Screw
7. 6x PW8 x40 Screw plug
8. 2x Carbon Filters ( HCA 62541 BH )
123
8
2.4 Package content
1- Hood
2- Chimney
3- User Manual
4- Blower flaps
7
6
4
5
5- ∅150/∅120 plastic adapter
6- 6x HS4,0x45 Screw
(Used for instalation of hood/chimney)
7- 6x PW8x40 Screw plug
(Used for instalation of hood/chimney)
8- 2x Carbon Filters

17 / EN
Hood / User Manual
!
Gas and electrical cooking
ranges L ≥ 65cm
mounting points. Use the drill and drill holes
(Fig. 8).
2. Insert extension bolts in the openings. In the
two holes marked as A insert screws (leaving
7 mm screw length on the outside as in Fig. 9).
3. Open the hood flap and remove the grease filter
(Fig.10).
4. Screw the chimney cover cramp, hang the hood
on two loosely fitted screws (Fig. 11).
5. Place the bubble level on the kitchen hood
body. By rotating the elements marked as A, set
the hood horizontally in accordance with the
indication of the bubble level and then tighten
the two loosely fitted screws and the two
remaining screws (Fig. 12).
6. Put the chimney cover on the body. Then gently
pull out the part of the hood that is marked as
B upwards until you will be able to screw it to
the cramp previously affixed to the wall (Fig. 13)
A
The installation must be carried out
very carefully, so as not to scratch
the chimney cover and the hood.
5 Installing your appliance
Before installation, the following must be done:
• Check that the dimensions of the purchased
product are adapted to the selected target spot.
• Disconnect and remove (if possible) the
furniture located in the installation area of the
hood to get easy access to the ceiling or wall
to which the hood is to be fitted. If this is not
possible, the elements located near the working
area must be secured.
• Verify if there is a plug socket close to the hood
installation area and if it is possible to connect
the hood to the vent pipe evacuating the vapors
outside.
• Verify if the drilling spots do not cover
installation wires (electrical, hydraulic, etc.).
• Be equipped with the following tools: measuring
tape, pencil, drill/ driver, drill Ø8, screwdriver,
bubble level.
5.2 Installation works
1. Determine the heating element axis and
transfer it to the wall where the hood will
be mounted on. Mark all the specific hood
Fig.7 Suggested
distance from the
kitchen cooker

18 / EN Hood / User Manual
5 Installing your appliance
Fig.8 Installation dimensions
Fig.9 Assembly of extension bolts
+
7mm
4 x O8 x 40mm
2 x O5 x 45mm
2 x O8 x 40mm

19 / EN
Hood / User Manual
Fig.10 Dismantling of aluminum grease filter
1
Fig.11 Suspending the hood
2
5 Installing your appliance