belavi 32720-23 User manual

User Manual
________________
Manual
del usuario
GRILL GAZEBO
English.... Page 3
Español.... Página 23
GLORIETA PARA PARRILLA
For Reference Only

Getting Started ................................ 3
Warnings & Cautions ....................... 4
Pack Contents/Parts ....................... 5
Parts List ......................................... 6
Hardware List .................................. 7
Assembly Instructions ..................... 8
Warranty .......................................... 19
Contents •Índice
Para comenzar ............................... 23
Advertencias y precauciones ......... 24
Contenido del paquete/piezas........ 25
Lista de piezas.................................. 26
Lista de herraje ............................... 27
Instrucciones de ensamblaje .......... 28
Garantía ........................................... 39
For Reference Only

3
Getting Started
Ensure all parts packaged in carton match the parts list.
Remove all protective materials and place parts on a
non-abrasive surface to avoid scratching. If any parts are
missing or damaged, DO NOT attempt to assemble. Please
contact our customer service center (Monday-Friday
9:00am – 5:00pm EST) at 1-800-599-8898.
Caution
Read all the instructions before assembly. Failure to
comply with instructions may result in faulty assembly and
potential injury! Assemble product on a soft, non-abrasive
surface such as a grass lawn or cardboard to avoid surface
scratches or damage to parts. Seek assistance to assemble
bulky or heavy items. After final alignment, make sure all
bolts and nuts are securely tightened with screw covers
pressed in place.
Cleaning & Maintenance
Wash canopy with a mild solution of soap and water; rinse
thoroughly. Dry completely.
Getting Started
For Reference Only

WARNING
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS PRODUCT/
ITEM FABRIC. This product/item is made with fabric that meets
CPAI-84 specicaons for ame resistance. It is not re proof. The
fabric will burn if le in connuous contact with any ame source. The
applicaon of any foreign substance to the product/item fabric may
render the ame-resistant properes ineecve.
Note: In case of adverse weather conditions or strong wind, please remove
the Main Canopy (U) from the gazebo.
The gazebo is designed to provide shade only. Do not use this gazebo in
strong wind and rain. Wind and rain can damage the gazebo and could
result in injury to you and others. It is not waterproof and not intended
for use in the rain. The water will sit easily on the canopy fabric and
severely damage the gazebo. Do not use or set up in rain, wind, or stormy
conditions.
This product is designed for leisure use only and is not a shelter against
adverse weather conditions.
Warnings & Cautions
1. Clean gazebo before storing, do not repack your gazebo until completely dry.
2. This gazebo must be assembled by two adults or more.
3. The gazebo canopy must be removed during windy or extreme conditions.
4. Loading limit of the utensil hook is 10 lbs (4.5 kgs).
5. Weight limit for basket and shelves is 35 lbs (15.8 kgs).
6. Steel components for garden accessories and furniture are treated with rust-
inhibiting paint. However, due to the nature of steel, surface oxidation (rusting)
will occur if this protective coating is scratched. This is a natural process. To
minimize this condition, it is recommended that care be taken when assembling and
handling the product in order to prevent the paint from being scratched. If scratching
or damage occurs, it is recommended that the area be touched up immediately
with rust-inhibiting paint (not included). Surface rust can be removed easily using
a very light application of common cooking oil. If surface oxidation (rusting) occurs
and no measures are taken to correct it, the oxidation may start dripping on the
deck or patio, which may cause damaging stains that may be difficult to remove.
For Reference Only

5
Contents
AUpper Pole VTop Canopy
BUpper Pole WMain Canopy
CUpper Pole AA Bolt (M6x15 mm)
DHalf-Arch BB Bolt (M6x25 mm)
EHalf-Arch CC Bolt (M6x35 mm)
FShelf DD Bolt & Washer (M6x20 mm)
GShort Arch EE Knob Screw
HCanopy Two-Tier Ribs FF M6 Nut
IBasket Panel GG Hex Key
JBasket Shelf
KBasket End
LLower Pole
MCanopy Connector
NRib Brace
OShelf Brace
PUtensil Rack
QStake
RBottle Opener
SFoot Cover
TConnector
UExtender
Pack Contents / Parts
For Reference Only

6
Descripon Qty Descripon Qty
A Upper Pole 1 P Utensil Rack 1
B Upper Pole 1 Q Stake 8
C Upper Pole 2 R Bole Opener 1
D Half-Arch 2 S Foot Cover 4
E Half-Arch 2 T Connector 4
F Shelf 2 U Extender 4
G Short Arch 2 V Top Canopy 1
HCanopy Two-Tier Ribs 4 W Main Canopy 1
IBasket Panel 2 AA Bolt (M6x15 mm) 45
JBasket Shelf 1 BB Bolt (M6x25 mm) 4
KBasket End 2 CC Bolt (M6x35 mm) 4
L Lower Pole 4 DD Bolt & Washer (M6x20 mm) 12
MCanopy Connector 1 EE Knob Screw 12
N Rib Brace 4 FF M6 Nut 4
O Shelf Brace 4 GG Hex Key 1
Parts List
FG
AA
J
K
L
V
W
P
R
S
D
E
BB
CC
DD
EE
FF
GG
B
C
C
AT
M
H
UN
O
I
Q
For Reference Only

7
A
B
I
W
G
F
E
D
C
B
A
V
AA BB CC EEDD
Hardware List
H
J
K
M
N
O
P
Q
R
S
L
T
U
GGFF
For Reference Only

8
Assembly Instructions
G
C
AA
AA
D
G
R
A
E
A
C
AA
C
G
B
E
D
D
C
CC
N
Bolt-Threading
Inserts
Fig. 2
Fig. 3
Fig. 1
AA
(18) Bolt
(M6x15 mm)
CC
(4) Bolt
(M6x35 mm)
For Reference Only

9
STEP 1:
Place Upper Pole (A), Upper Pole (B), and both Upper Poles (C) on the
ground as illustrated here. Please take note that parts A, and B are
perpendicular, as well as both part C’s. In addition, please take note of
the bolt-threading inserts, and the directions these should be facing
when placed on the ground.
Insert two M6x15 Bolts (AA) through eyelets on Bottle Opener (R), and
into the bolt-threading inserts found on Upper Pole (A), see Fig. 1.
Insert two M6x15 Bolts (AA) through eyelets at the end of Short Arch (G),
and into the bolt-threading inserts found at the top of Upper Pole (C)
that is parallel to Upper Pole (A), see Fig. 2. Insert two M6x15 Bolts (AA)
through eyelets at the opposite end of Short Arch (G), and into the bolt-
threading inserts found at the top of Upper Pole (A). Follow these steps
to connect the second part H to part B, and the second part C.
Insert two M6x15 Bolts (AA) through eyelets at the end of Half-Arch (D),
and into the bolt-threading inserts found at the tops of both Upper
Poles (C), see Fig. 3.
Insert two M6x15 Bolts (AA) through eyelets at the end of Half-Arch (E),
and into the bolt-threading inserts found at the tops of Upper Pole (A),
and Upper Pole (B).
Insert one M6x35 Bolt (CC) through eyelet of Rib Brace (N), and into
the bolt-threading found at the tops of both Upper Poles (C), see Fig.
3. Follow this step to connect remaining part N’s to the tops of part A,
and part B.
*Do not tighten bolts down completely during this portion of assembly.
Assembly Instructions
For Reference Only

10
Assembly Instructions
STEP 2:
Place previously constructed parts upright as illustrated here. Place
one Connector (T) over each end where Half-Arch (E), and Half-Arch
(D) meet, see Fig. 4. Please note, that the eyelets on Connector (T), and
the bolt-threading inserts on part D, and part E will be facing outward.
Insert two M6x15 Bolts (AA) through eyelets on each Connector (T),
and into the bolt-threading inserts on Half-Arch (E), and Half-Arch (D),
see Fig. 5. Follow these steps to connect the second part E, and part D,
using the remaining part T’s.
D
AA
E
DE
DE
T
Fig. 5
Fig. 4
*Do not tighten bolts down completely during this portion of assembly.
AA
(8) Bolt
(M6x15 mm)
For Reference Only

11
Assembly Instructions
STEP 3:
Insert the lower rib of each Canopy Two-Tier Ribs (H) into the open
ends of Canopy Connector (M), see Fig. 6, using the push-pins on part
H to secure these parts together.
H
H
H
H
M
M
H
H
H
H
Fig. 6
For Reference Only

12
Assembly Instructions
STEP 4:
Place previously assembled Canopy Two-Tier Ribs (H), with Canopy
Connector (M), over the frame as illustrated here. Set the lower ribs of
each Canopy Two-Tier Ribs (H) in between the Rib Braces (N) at the top
of each upper pole.
Insert one M6x25 Bolt (BB) through eyelet on the side of Rib Brace (N),
through eyelets on the lower rib of Canopy Two-Tier Ribs (H), through
eyelet on opposite side of part N, and secure parts together using M6
Nut (FF), see Fig. 8. Follow this step to secure remaining part H’s with
part N’s.
Place one Extender (U) on the ends of Canopy Two-Tier Ribs (H) by
pressing in on push-pins at the end of part H, and pushing against part
U to secure them together, see Fig. 9. Continue pressing part U further
in until the push-pin of part H reaches the third eyelet.
Tighten all bolts, and nuts left loose throughout assembly process.
BB
U U U
FF
Fig. 9
Fig. 8
BB
(4) Bolt
(M6x25 mm)
FF
(4) Nut
(M6)
For Reference Only

13
Assembly Instructions
*Do not tighten bolts down completely during this portion of assembly.
STEP 5:
Insert three M6x20 Bolts & Washers (DD) through eyelets on Basket
Panel (I), and into bolt-threading inserts on the side of Basket Shelf (J),
see Fig. 10. Follow this step to assemble the second Basket Panel (I) to
the opposite side of Basket Shelf (J).
DD
I
I
J
Fig. 10
DD
(6) Bolt
(M6x20 mm)
For Reference Only

14
Assembly Instructions
STEP 6:
Place one Basket End (K) in between Basket Panels (I) on both ends of
Basket Shelf (J), see Fig. 11 for the correct orientation of part K.
Insert one M6x20 Bolt & Washer (DD) through eyelets on Basket Panels
(I), and into the bolt-threading inserts on the sides of Basket End (K),
see Fig. 11. Follow this step to connect the second part K to the opposite
end of part J, and both part I’s.
Insert one M6x20 Bolt & Washer (DD) through the eyelet underneath
Basket Shelf (J), and into the bolt-threading insert on the bottom of
Basket End (K), see Fig. 11. Follow this step to connect the second part K
at the opposite end of part J.
Tighten all bolts left loose during assembly of this component.
DD K
K
KFig. 11
DD
(6) Bolt
(M6x20 mm)
For Reference Only

15
STEP 7:
Place previously assembled basket in between Upper Pole (B), and
Upper Pole (C). Insert two Knob Screws (EE) through eyelets of brace
on Basket End (K), and into the lower two of four bolt-threading inserts
on Upper Pole (C), see Fig. 12. Follow this step to connect part K at the
opposite end of basket to part B.
EE
Assembly Instructions
Fig. 12
EE
(4) Knob Screws
For Reference Only

16
STEP 8:
Insert two M6x15 Bolts (AA) through eyelets of Shelf Brace (O), and into
the bolt-threading inserts found at the end, underneath Shelf (F), see
Fig. 13. Follow this step to connect second part O to the opposite end of
part F. Follow these steps to connect remaining part O’s to second part F.
Insert two Knob Screws (EE) through eyelets on Shelf Brace (O), and
into upper two of four bolt-threading inserts on Upper Pole (A), see
Fig. 14. Follow this step to connect part O at the opposite end of part F
to part C. Follow these steps to connect second part F with part O’s to
part B, and second part C.
Insert three M6x15 Bolts (AA) through eyelets of Utensil Rack (P), and
into the bolt-threading inserts found on the side, underneath Shelf (F),
see Fig. 15. The hooks of Utensil Rack (P) should be facing inward, see
Fig. 15 for correct orientation.
PAA
F
EE
F
F
AA
Assembly Instructions
Fig. 15
Fig. 14
Fig. 13
AA
(11) Bolt
(M6x25 mm)
EE
(8) Knob Screws
For Reference Only

17
STEP 9:
Unfold Main Canopy (W), and place it over the lower ribs of Canopy
Two-Tier Ribs (H). The upper ribs of part H should be over the canopy
when finish, and this canopy should be flush with these lower ribs.
Place Top Canopy (V) over upper ribs of Canopy Two-Tier Ribs (H). Insert
the ends of these ribs into the corner pockets underneath Top Canopy
(V).
Insert Extenders (U) found at the ends of the lower ribs of Canopy Two-
Tier Ribs (H) into the corner pockets underneath Main Canopy (W), see
Fig. 16. Extend the Extender (U) by pressing in on push-pin, and pulling
the part out till the push-pin locks into a different eyelet, see Fig. 17.
Go to remaining corners, and extend each part U which will continue
making the canopy taut.
W
V
U
U
W
W
Assembly Instructions
Fig. 17Fig. 16
For Reference Only

18
STEP 10:
Insert Lower Poles (L) through openings of Foot Covers (S), see Fig 18.
Insert the openings at the bottoms of Upper Poles (A, B, & C) into the
tops of Lower Poles (L), see Fig. 18.
Insert two M6x15 Bolts (AA) through eyelets of Upper Pole (C), and into
the bolt-threading inserts of Lower Pole (L), see Fig. 19. Follow this step
to connect remaining part L’s to part A, B, and second part C.
Insert Stakes (Q) through eyelets of the Lower Pole’s (L) bases, see Fig.
20. Turn Stakes (Q) clockwise to secure them, and the grill gazebo to
the ground.
L
S
AA
Q
Assembly Instructions
Fig. 20
Fig. 19
Fig. 18
AA
(8) Bolt
(M6x15 mm)
For Reference Only

822694
[email protected]
1800 599 8898
E-Mail:
Address:
Name:
Your details:
Descripon of problem:
SERVICE CENTER
PRODUCT CODE
AFTER SALES SUPPORT
WARRANTY CARD
US
GRILL
GAZEBO
32720-23
MODEL NUMBER
TDC USA, Inc.
5 Industrial Road, STE 1
Fairfield, NJ 07004-3017
United States of America
Phone lines available Monday to Friday
9am - 5pm EST.
Please contact our AFTER SALES SUPPORT by phone or e-mail when
needing assistance with your purchase.
Please retain your sales receipt which validates the 1-year Limited Warranty.
Only submit the Warranty Card when needing assistance with a faulty part.
For Reference Only

Dear Customer:
The ALDI warranty is a full warranty oering you the following benets:
Warranty period:
Costs:
Hotline:
Operang hours:
1 year* from date of purchase
6 months for movable parts and consumables under
normal and proper condions of use.
Free repair/exchange or refund.
No shipping or handling costs
1-800-599-8898
Monday - Friday, 9:00 AM - 5:00 PM EST
Please contact our service hotline by phone, email, or fax when needing assistance
with assembly or with faulty parts. This allows us to provide support in the event of
possible operator errors.
ALDI INC. FULL WARRANTY CONDITIONS
In order to make a claim under the warranty, please send us:
A copy of your sales receipt, your completed warranty card with contact
informaon provided, and an explanaon as to how we can help and what
concerns you have with any parts.
The warranty does not cover damage caused by:
• Accident or unancipated events to frame [metal parts] (e.g. wind, snow,
lighng, re).
• Deterioraon, fading, sagging, or unancipated events to canopies and
neng panels (e.g. wind, sun, rain, pets/animals).
• Improper use or transport.
• Failure to follow safety and maintenance instrucons.
• Other improper treatment or modicaon.
Aer the expiraon of the warranty period, you may have your product repaired at
your own expense. You will be noed of the repair costs in advance.
This warranty gives you specic legal rights, which may vary from state to state,
that are not intended to exceed statutory minimum requirements beyond what is
included above.
This warranty does not limit the statutory obligaon of the seller arising from any
implied warranes. The period of warranty can only be extended in accordance
with applicable law.
For Reference Only