Belkin F7C008 User manual

Conserve Valet™
Smart USB Charging Station
User Guide

2
A charger left plugged into the
wall can still draw power—even
when no device is attached.
The Conserve Valet Smart
USB Charging Station charges
up to four devices at once
and shuts off automatically.
The product itself draws zero
power when not in use—so you
can keep your devices ready to
go without wasting energy.
For more information and
to learn about other Belkin
Conserve energy management
products, please go to
belkin.com/conserve
Package Contents
. Conserve Valet Smart USB
Charging Station
. 1x (4.25-foot) AC Power Cord
. 1x (1-foot) USB to Mini-USB Cord
. 1x (1-foot) USB to Micro-USB Cord
. User Guide and
Warranty Information
start button
LED power indicator
AC power
cord inlet
3 USB ports
non-slip device surface
cord
management
convenience USB port
for side access

3
QUICK SETUP GUIDE
1
Plug in your USB device cords that
you want to use with your Conserve
Valet Smart USB Charging Station.
NOTE: We advise you to use the
USB cable that came with your mobile
device. If your device did not come
with a USB cable, please refer to your
manufacturer for availability. We have
included a USB to Mini-USB Cable
and a USB to Micro-USB Cable,
which might work with your devices.
2
Wind your USB cords around the
inner spool of your Conserve Valet
to manage the cords. You can
choose not to do this if you prefer.
3
Secure your USB cords by clipping
them into the appropriate eyelet
located under the lower housing of
your Conserve Valet.

4
4
Plug the AC power cord into your
Conserve Valet and plug the other
end into a power outlet.
5
Connect your devices to their
respective USB cords and place
them on the Conserve Valet pad.
6
Press the light-green power button
and the LED will illuminate; power
is now flowing to your devices.

5
7
Once all connected devices are
charged (approximately 4 hours), the
LED light will flash 3 times and your
Conserve Valet will power down.
If you connect an additional device
during charging, the Valet will
restart the charge time to ensure
that the new device is fully charged
before powering down. If you
unplug all your devices, the Valet
will automatically power down after
2 minutes.
NOTE: When sitting idle, the
Conserve Valet uses no power.
PRODUCT FEATURES
. Zero power consumption when not in use
.Push-button start
. Auto-off function
-
Conserve Valet turns off when all
devices are charged.
-
Conserve Valet will power down after
two minutes if all the devices are
disconnected.
. Auto-restart function
-
Conserve Valet senses when you plug
in an additional device and restarts the
charge time to ensure the added device
receives a full charge.
.
Non-slip finish on tray to prevent
device slippage
.
Cord management
-
Inner spool for cord storage and
management
-
Cut-out clips located underneath tray
to secure cord placement
.
LED light to show Conserve Valet activity
.
4x USB output (3 located on rear side,
1 located on side for easy-access
charging)
.
1x (1-foot) USB Type A to Mini-B cord
included
.
1x (1-foot) USB Type A to Micro-B cord
included
.
Universal IEC C8 AC power inlet
.
1 x (4.25-foot) IEC C7 “figure 8” power
cord included
DEVICES YOU CAN CHARGE WITH THE
CONSERVE VALET
Most MP3 players, smart phones,
digital cameras, and other portable
devices that use a USB input to charge
should work with the Conserve Valet.
Devices with large color screens, such
as smart phones, often require a lot of
power to charge. It is recommended
you only charge two of these devices
at the same time.
You will be able to charge most of
your devices with the Conserve Valet
(5-volt USB charge). You should use
your device’s included USB charge
cord when connecting to the Conserve
Valet. If your device did not come with
a USB cord, check with the device’s
manufacturer for USB cord availability.
The included Belkin USB cords are
compatible with devices that have a
Mini-B or Micro-B USB charge port.