Belkin F5U234 User manual

EN
FR
DE
NL
IT
ES
Hi-Speed USB 2.0
4-Port Hub
Connect up to 4 Hi-Speed
USB 2.0 or 1.1 devices
F5U234User Manual

EN
Hi-Speed USB 2.0
4-Port Hub
Connect up to 4 Hi-Speed
USB 2.0 or 1.1 devices
F5U234User Manual

6
Table of Contents
Introduction ...............................................................................................1
Overview .....................................................................................................2
Features ...............................................................................................2
Package Contents ................................................................................2
Technical Specifications ......................................................................3
Installation .................................................................................................4
Information .................................................................................................7

1
EN
Introduction
Welcome to Belkin USB 2.0!
Congratulations and thank you for purchasing the Belkin Hi-Speed USB 2.0
4-Port Hub (the Hub). The Hub provides four downstream USB ports that
offer backward-compatible, Plug-and-Play connectivity with all USB devices,
including USB 1.1 (or low- and full-speed) devices, as well as with USB
2.0 (or high-speed) devices. This includes such peripherals as scanners,
printers, mass-storage devices, and high-resolution cameras. The Hub is
self-powered, which allows the cascading of devices with additional hubs, so
that up to 127 USB devices may be connected to a single port.
The Hub is uniquely designed to allow the user to position the four
downstream ports toward the back of the desktop for efficient cable
management, or to the front of the desktop for easier port access. The Hub
also provides a status LED for each individual port and a master power LED.

2
EN
2
Overview
Features
• Compliant with Universal Serial Bus specification 2.0
(data rate 1.5/12/480Mbps)
• Backward-compatible with Universal Serial Bus specification 1.1
(data rate 1.5/12Mbps)
• Compatible with Windows® 98 SE, Me, 2000, and XP
• Approved by USB Implementers Forum (USB-IF)
• Supports Plug-and-Play specifications
• Supports “hot swapping” of USB devices
• Over-current detection and protection
• Individual port-status indicator LEDs
• Four 480Mbps downstream ports
• Fully compatible with USB 1.1 and USB 2.0 devices
• Compact, slim-line design
• Multiple hubs may be stacked on top of one another
Package Contents
• Hi-Speed USB 2.0 4-Port Hub
• AC Power Adapter
• User Manual
• USB device cable

3
3
EN
Technical Specifications
Upstream Ports (1)
Downstream Ports (4)
Power Mode Self-powered/bus-powered
Per-Port Voltage DC +5V
Per Port Current Self-Powered Mode: 500mA (max)
Bus-Powered Mode: 100mA (max) (Ports one and two only)
Operating Temperature 5º C ~ 40º C
Storage Temperature -20º C ~ 60º C
Enclosure ABS
Power Supply
Output: DC 5V, 2.1A
Plug Size: 3.5mm (outer)
1.0mm (center)
Plug Polarity: Center Positive
Main Power LED Color Definitions:
Off Not operational
Red Operational
Port Status LED Color Definitions:
Off Not operational, or no device connected
Green Fully operational
Amber Over-current condition
Important Note: Please do not connect any USB devices to the Hub until
instructed to do so in step 4 of this installation procedure.
Overview

4
EN
4
Important Note: Please do not connect any USB devices to the Hub until
instructed to do so in step 4 of this installation procedure.
1. Plug the AC adapter into a wall outlet, or surge suppressor. Plug the DC
connector into the DC Power Jack found on the side of the Hub.
Important Note: The Hub may be used without the power supply when
connecting devices that draw 100mA of current or less, however, only port 1
and port 2 will be functional.
2. Plug the flat end of the provided USB device cable into the downstream
port of your computer or downstream port of another hub, then plug the
mini 6-pin connector of the device cable into the upstream port on the
rear of the Hub.
Important Note:The Hub must be connected to a USB 2.0-compliant host
in order to function in high-speed mode (480Mbps data rate). If the Hub is
connected to a USB 1.1-compliant host, it will operate only in low-speed or
full-speed mode (1.5Mbps/12Mbps).
3. Windows will now detect your Hub and install the required driver support.
(The Windows “Install New Hardware Wizard” may prompt you to provide
your Windows Installation CD to complete the driver installation process).
Important Note: High-speed hub drivers are included with most USB 2.0 PCI
upgrade cards, and are pre-installed along with the PCI card drivers. If you
purchased an upgrade card prior to the release of high-speed hub support,
please check with your PCI card vendor for an updated USB 2.0 driver. The
Belkin USB 2.0 driver supports all competitive cards based on the NEC host
controller with the exception of Adaptec. The most recent Belkin driver is
available at www.belkin.com.
Installation

5
5
EN
Installation
4. Plug the USB-A connector of the USB device, or an additional hub, into any
of the downstream ports of the Hub.
Important Note: When moving a device from one port on the Hub to another,
it may be necessary to reinstall the USB drivers for that device.

6
EN
Installation
6