Bell'O AVSC4260 User manual

AVSC4260
AUDI /VIDE TELEVISI N SYSTEM
ASSEMB Y INSTRUCTIONS

2
Bell’O International Corp. will not be responsible for failure to assemble as directed or for the improper assembly, use or handling of this stand.
FOR YOUR SAFETY, PLEASE FOLLO THESE PRECAUTIONS:
! DO NOT P ACE ITEMS ON THE SHE VES WHICH EXCEED THE MAXIMUM WEIGHT IMITS OF 125 BS. FOR TOP SHE F,
50 BS. FOR THE MIDD E SHE F, AND 75 BS. FOR THE BOTTOM SHE F.
A WAYS P ACE THE HEAVIEST
COMPONENTS ON THE BOTTOM SHE F.
! ALWAYS REM VE THE TV AND THER EQUIPMENT FR M THE FURNITURE PRI R T M VING THE ASSEMBLED UNIT.
! D N TM VE THE ASSEMBLED FURNITURE AFTER THE GLASS SHELVES HAVE BEEN INSTALLED, AND/ R
WHEN THERE IS EQUIPMENT L CATED N THE FURNITURE AS THIS MAY CAUSE THE SHELVES AND THER
ITEMS T BEC ME UNSECURED AND FALL.
! WHEN IN USE, THIS FURNITURE MUST BE PLACED N A FLAT, S LID AND LEVEL SURFACE.
! D N T LEAN N THE TV WHEN IT IS N THE TV STAND.
! D N T CLIMB R STEP N THE STAND.
! D N T BANG INT R PLACE Y UR WN WEIGHT N THE GLASS SHELVES.

3
PARTS IST
#
DSYF1
DSYF2
DSYF3
DSYF4
DSYF5
2
4
2
12
8
Quantity
Part
#
DSYF6
DSYF7
DSYF8
DSYF9
DSYF10
1
4
4
2
3
Quantity
Part
12 mm
32 mm
35 mm

4
PARTS IST
#
DSYF11
DSYF12
DSYF13
DSYF14
DSYF15
1
1
1
1
1
Quantity
Part
#
DSYF16
DSYF17
DSYF18
DSYF19
DSYF20
1
1
1
1
1
Quantity
Part

ASSEMB Y INSTRUCTIONS
NOTE: 2 PE PLE ARE REC MMENDED T ASSEMBLE THIS FURNITURE. T AV ID DAMAGE DURING ASSEMBLY, IT SH ULD BE ASSEMBLED
N A S FT SURFACE.
1. ATTACH the Top Shelf Support Bar (DSYF12) to the back of the Front Wood Frame (DSYF11) using four 32 mm Screws (DSYF2)
as shown above. Tighten fully, but be careful not to overtighten.
2. ATTACH the Bottom Shelf Support Bar (DSYF13) to the back of the Front Wood Frame (DSYF11) using four 32 mm Screws
(DSYF2). Tighten fully, but be careful not to overtighten.
3. S IDE four Glass Bumper Rings (DSYF4) onto the Middle Shelf Support Bar (DSYF14) as shown in Fig. 1A.
SPACE them evenly apart.
4. ATTACH the Middle Shelf Support Bar (DSYF14) to the back of the Front Wood Frame (DSYF11) using two 12 mm Screws
(DSYF1). Tighten fully, but be careful not to overtighten.
5
Fig. 1
Fig. 1A
DSYF2
DSYF12
DSYF13
DSYF1
DSYF1
DSYF14 DSYF14
DSYF2
DSYF11
DSYF4

7
Fig. 2
DSYF1
DSYF11
DSYF15
DSYF1
DSYF16
5. ATTACH the Right Side Frame (DSYF15) to the back of the Front Wood Frame (DSYF11) using three 12 mm Screws (DSYF1) as
shown above. Tighten fully, but be careful not to overtighten.
6. ATTACH the Left Side Frame (DSYF16) to the back of the Front Wood Frame (DSYF11) using three 12 mm Screws (DSYF1) as
shown above. Tighten fully, but be careful not to overtighten.

8
Fig. 3
7. ATTACH the Rear CMS®(Cable Management System) Panel (DSYF17) to the Right and Left Side Frames (DSYF15, DSYF16) and
SECURE using four 32 mm Screws (DSYF2) as shown above. Tighten fully.
8. SCREW two Large Adjustable Glass Pads (DSYF5) into the prethreaded holes at the tops of the Right and Left Side Frames
(DSYF15, DSYF16) as shown.
9. SCREW three Small Adjustable Glass Pads (DSYF6) into the prethreaded holes at the tops of the Rear CMS®Panel(DSYF17) and
TopShelf Support Bar (DSYF12) as shown.
DSYF2
DSYF2
DSYF16
DSYF6
DSYF17
DSYF15 DSYF5
DSYF5

9
10. SCREW two Rear Shelf Support Posts (DSYF7) into the prethreaded holes in the Rear CMS®Panel (DSYF17) as shown above. Tighten fully by hand.
11. SCREW four Shelf Support Clips (DSYF8) into the prethreaded holes in the rear of the Right and Left Side Frames (DSYF15, DSYF16) as shown.
NOTE: For the two BOTTOM Shelf Support Clips, make sure the small screw in each Clip is positioned upward before tightening fully, or else
this small screw will be difficult to tighten once the Glass Shelf is installed. For the MIDDLE Shelf Support Clip, the small screw can be
positioned either up or down. Make sure the small screw is not in too far so there is enough space for the Glass Shelves to be inserted later.
12. APP Y four Soft Glass Pads (DSYF9), evenly spaced, along the bottom edge of the Front Wood Frame (DSYF11) as shown.
DSYF16
DSYF15
DSYF8
DSYF9
DSYF11
DSYF7
DSYF17
Fig. 4

10
Fig. 5
Fig. 5A
DSYF18
DSYF3
DSYF11
DSYF3
DSYF19
DSYF20
DSYF8

11
13. Carefully P ACE the Bottom Glass Shelf (DSYF20) down onto the Soft Glass Pads (DSYF9) on the bottom edge of the Front
Wood Frame (DSYF11) and fully INSERT the back edge of the Bottom Glass Shelf into the two bottom Shelf Support Clips
(DSYF8). TIGHTEN the small screws in the Shelf Support Clips to lock the Glass Shelf into place as shown in Fig. 5A. Do not
overtighten.
14. Carefully P ACE the Middle Glass Shelf (DSYF19) down onto the Middle Shelf Suport Bar (DSYF14) and fully INSERT the back
edge of the Middle Glass Shelf into the two middle Shelf Support Clips (DSYF8). TIGHTEN the small screws in the Shelf Support
Clips to lock the Glass Shelf into place as shown in Fig. 5A. Do not overtighten.
15. Carefully P ACE the Top Glass Shelf (DSYF18) down into place. Carefully INSERT the discs under the Top Glass Shelf into the
holes in the top edges of the Right and Left Side Frames (DSYF15, DSYF16). SECURE the Top Glass Shelf using two 35 mm
Screws (DSYF3) as shown above. Do not overtighten.
NOTE:Rotate the Adjustable Glass Pads (DSYF5, DSYF6) under the Top GlassShelf to properly support and level the Shelf
before placing any items on it. All shelves must be correctly installed, properly supported, and level before placing any
components on them.