Bell'O Triple Play TPC2133 User manual

F AT PANE TV MOUNTING SYSTEM
ASSEMBLY NSTRUCT ONS
TPC2133
OPTION 1 OPTION 2 OPTION 3
Flat Panel TV Stand Stand with TV Mounting System Stand with Wall Mount

! DO NOT PLACE TEMS ON THE SHELVES (OR TV MOUNT) WH CH EXCEED THE MAX MUM WE GHT L M TS
OF 125 LBS. FOR THE TV, 50 LBS. FOR M DDLE SHELF, AND 75 LBS. FOR LOWER SHELF. ALWAYS PLACE
THE HEAV EST COMPONENTS ON THE BOTTOM SHELF.
! ONLY WALL MOUNT NTO WOOD STUDS OR CONCRETE WALLS. DO NOT ATTEMPT TO WALL MOUNT THE
TELEV S ON NTO DRYWALL ONLY.
! THE MAX MUM WE GHT OF YOUR TELEV S ON CANNOT EXCEED THE MAX MUM WE GHT RAT NG OF THE
WALL MOUNT.
! ALWAYS REMOVE THE TV AND OTHER EQU PMENT FROM THE FURN TURE PR OR TO MOV NG THE
ASSEMBLED UN T.
! WHEN N USE, TH S FURN TURE MUST BE PLACED ON A FLAT, SOL D AND LEVEL SURFACE.
! DO NOT LEAN ON THE TV WHEN T S ON THE TV STAND.
! DO NOT CL MB OR STEP ON THE STAND.
! DO NOT BANG NTO OR PLACE YOUR OWN WE GHT ON ANY OF THE SHELVES.
! TH S PRODUCT WAS DES GNED TO BE NSTALLED AND UT L ZED ONLY AS SPEC F ED N TH S MANUAL.
BELL’O NTERNAT ONAL CORPORAT ON W LL NOT BE RESPONS BLE FOR FA LURE TO ASSEMBLE AS
D RECTED OR FOR THE MPROPER ASSEMBLY, USE, OR HANDL NG OF TH S PRODUCT.
! MPROPER NSTALLAT ON OF TH S PRODUCT MAY CAUSE DAMAGE OR SER OUS NJURY. BELL'O
NTERNAT ONAL CORPORAT ON CANNOT BE L ABLE FOR D RECT OR ND RECT DAMAGE OR NJURY
CAUSED BY NCORRECT MOUNT NG, NCORRECT USE, OR NCORRECT ASSEMBLY.
! F THE MOUNT NG BRACKET W LL BE ATTACHED TO ANY STRUCTURE OTHER THAN SPEC F ED N TH S
MANUAL, ONLY A L CENSED PROFESS ONAL CONTRACTOR/ NSTALLER SHOULD PERFORM TH S
NSTALLAT ON. THE SUPPORT NG STRUCTURE MUST SUPPORT, AT M N MUM, FOUR T MES THE COMB NED
WE GHT OF THE MOUNT NG BRACKET AND TV. T S THE RESPONS B L TY AND L AB L TY OF THE NSTALLER
TO ENSURE THE SU TAB L TY OF THE SUPPORT NG STRUCTURE.
! THE MOUNT W TH THE NCLUDED HARDWARE S NOT UL L STED FOR NSTALLAT ON NTO METAL STUDS.
FOR THE AVA LAB L TY OF UL L STED METAL STUD MOUNT NG HARDWARE, MON TOR WE GHT L M T AND
NSTALLAT ON NSTRUCT ONS PLEASE CHECK W TH YOUR RETA LER OR AN NSTALLAT ON PROFESS ON AL.
FOR YOUR SAFETY, PLEASE FOLLOW THESE PRECAUTIONS:

PARTS LIST
1
M1
#
M2
M3
M4
M5
1
1
2
1
1
1
Quantity
Part
M6
M7
1
M8
#
M9
M10
M11
M12
1
5
2
4
2
1
Quantity
Part
M13
M14
65 mm
15 mm
30 mm

4
4
4
4
TVM7
PARTS LIST
TV MOUNTING SCREWS
4
TVM1
#
TVM2
TVM3
TVM4
TVM5
4
4
4
4
Quantity
Part
#
4
4
4
Quantity
Part
TVM8
TVM9
TVM10
TVM11
TVM12
4 x 15 mm
4 x 30 mm
5 x 15 mm
5 x 30 mm
6 x 15 mm
6 x 35 mm
8 x 20 mm
8 x 40 mm
Short Spacer
Long Spacer
Washer
Washer
M6/M8
19mm
M4/M5
19mm
TVM6
4
M18
#
M21
M22 1
1
Quantity
Part
2
M15
#
M16
M17 4
4
Quantity
Part
27 mm
M19
M20 2
2

Fig. 1-1
M1
OPTION 1: FLAT PANEL TV STAND
NOTE: 2 PEOP E ARE RECOMMENDED TO ASSEMB E THIS FURNITURE. TO AVOID DAMAGE DURING ASSEMB Y, IT SHOU D BE ASSEMB ED ON A
SOFT SURFACE.
1-1. REMOVE the Frame Assembly (M1) from the packaging and UNFOLD as shown.

Fig. 1-2
M1
1-2. LOCK the Frame Assembly (M1) into an open position by engaging the ocking Mechanisms as shown.
NOTE: IF YOU WILL BE USING THE TPC2133 WITH THE TV MOUNTING SYSTEM (OPTION 2), CONTINUE FOR FURTHER
INSTRUCTIONS. IF YOU WILL BE USING THE WALL MOUNT FEATURE (OPTION 3), PLEASE SKIP TO PAGE 14.

Fig. 2-1
(View from Front)
M10
M2
M1
M2
M3
M11
2-1. NSERT the bottom pegs of the Flat Panel Support Post (M2) into the holes at the BOTTOM rear of the CMS®(Cable Management
System) Panel (M1) and PUSH down. SECURE with two 65 mm Screw Knobs (M10) as shown in Fig. 2-1.
2-2. ATTACH the Mounting Bracket (M3) to the FRONT of the Flat Panel Support Post (M2) with four 15 mm Bolts (M11).
OPTION 2: FLAT PANEL TV MOUNTING SYSTEM
(View from Rear)

TELEVISION
(!)
S ACER
WASHER
2-3. SELECT THE CORRECT SCREW. Before beginning, test several of the Screws in your Hardware Kit to find the correct size
and length for your television.
NOTE (!): Use Spacers if Monitor Arms (M5) do not fit firmly against the back of the television, such as when the back of the
television is curved, contains larger recessed mounting holes, or some other obstruction is in the way. Spacers also provide extra
room for cables. The Arms must rest securely on the spacers, and should not be loose.
MONITOR ARM (M5)
MOUNTING THE TELEVISION
CAUTION: CAREFULLY DETER INE THE CORRECT OUNTING PROCEDURE TO PREVENT DA AGE TO YOUR TV AND/OR BELL'O
®
OUNTING SYSTE . ALWAYS RE OVE THE TELEVISION & CO PONENTS BEFORE ATTE PTING TO OVE THE STAND.
Fig. 2-2

Fig. 2-3
2-4. SL DE Monitor Arms (M5) on to the Swivel Bar (M4) and then NSERT the 30 mm Turn Knobs (M12) through the Monitor Arms as shown.
DO NOT YET FULLY TIGHTEN THE KNOBS.
2-5.
PLACE your TV face-down on a very soft, non-abrasive surface, taking extreme caution to not damage the face of your TV.
2-6. ATTACH each Monitor Arm (M5) to the back of your television as shown with selected screws. Make sure that each Washer is placed
between the Screw and the Monitor Arm. DO NOT PLACE THE WASHERS BETWEEN THE ARMS AND THE TELEVISION.
DO NOT YET FULLY TIGHTEN SCREWS.
2-7.
Make sure the Swivel Bar (M4) and Monitor Arms (M5) are level and m ake any necessary adjustments. Then go back and T GHTEN ALL
Screws and Turn Knobs (M12) fully.
M5
M12
M4

Fig. 2-4
M4
M4
M3
M2
M2
M13
2-8. With the help of an assistant, carefully PLACE the Post of the Swivel Bar (M4) down into the tube in the Mounting
Bracket (M3), and SECURE with the Post ocking Clip (M13) as shown.
SKIP TO PAGE 20 FOR GLASS SHELF INSTALLATION INSTRUCTIONS.

Fig. 3-1
OPTION 3: STAND WITH WALL MOUNT
3-1 Using a stud finder, F ND the exact location of the studs to which you want to attach the Wall Mount (M9). MARK the right and left side
to determine the center of each stud. [FIGURE 3-1]
CAUTION: NEVER EXCEED THE AXI U LOAD CAPACITY OF 125 LBS (56.7 kG)

• Height to bottom of TV
Fig. 3-2
3-2. MEASURE the distance from the mounting holes on the back of your television to the top and bottom edges of the television to
determine the true center of the television once it will be mounted. Many television manufacturers do not place the mounting holes
exactly centered in the television.
3-3. MEASURE from the floor up, and make small marks on the wall to help you determine the desired TV height. Using a level, L NE UP
the Installation Template with your pencil markings and TAPE it into place. [FIGURE 3-2]

5/32"
(4 mm)
2.5"
(64 mm)
NSTALL NG THE WALL MOUNT N WOOD:
3-4. DR LL four holes 2.5" (64 mm) deep using a 5/32" (or 4 mm) size drill bit in the “A”, “B”, “C”, and “D” locations noted on the
Installation Template.
Fig. 3-3
A
C
B
D
USE LINES ON INSTALLATION TEMPLATE TO ALIGN TEMPLATE WITH STUD PENCIL MAR INGS.

MOUNT NG TO SOL D CONCRETE OR C NDER BLOCK:
3-4. Carefully DR LL four holes using a 5/16" (or 8mm) masonry drill bit in the “A”, “B”, “C”, and “D” locations noted on the Installation
Template. NOTE: EACH HOLE SHOULD BE AT LEAST 3" (76 MM) DEEP. [FIGURE 3-4]
IMPORTANT: DO NOT DRILL INTO MORTAR JOINTS! DRILL HOLES AT LEAST 1" (25.4 MM) FROM THE JOINTS.
3"
(76 mm)
Fig. 3-4
A
C
B
D
USE LINES ON INSTALLATION TEMPLATE TO ALIGN TEMPLATE WITH STUD PENCIL MAR INGS.

3-5. REMOVE the Installation Template.
3-6. If mounting into concrete, NSERT four
TOGG ER®brand Wall Anchors (M17) into
the drilled holes. [FIGURE 3-7]
3-7. PLACE the Wall Plate (M9) over the holes
and SCREW in the ag Bolts (M18) about
half way. Use a LEVEL to make sure the
Wall Plate is level and make any necessary
adjustments. Once straight, T GHTEN all of
the ag Bolts completely (DO NOT OVER
T GHTEN!)
Fig. 3-5
Fig. 3-6
Fig. 3-7
M18
M18
M17
M9
M9

Fig. 3-8
3-8. ATTACH the Mounting Bracket (M3) to the Wall Plate (M9) with four 15 mm Bolts (M11). T GHTEN FULLY.
M9
M3
M11
M4
M4
M3
M3
M13
3-9. With the help of an assistant, carefully
PLACE the Post of the Swivel Bar (M4)
down into the tube in the Mounting
Bracket (M3), and SECURE with the Post
ocking Clip (M13) as shown.
Fig. 3-9

INSTALL THE GLASS SHELVES
CAUTION: ALWAYS RE OVE THE GLASS SHELVES BEFORE ATTACHING/RE OVING YOUR
TELEVISION, OR BEFORE ATTE PTING TO OVE THE STAND.
Fig. 4-1
M19 M20
M19
M1
M20
4-1. ATTACH the Middle Shelf Rear Support Brackets (M19) to the front of the CMS®Panel (M1) with small Screws (M20) as shown.

4-2. Carefully NSTALL the Top Glass Shelf (M8) as shown above. Make sure the silver posts under the Top Glass Shelf are properly inserted
into the holes in the Top Shelf Support Bar (M1). SECURE the Top Glass Shelf to the Support Bar using four 27 mm Turn Knobs (M16) as
shown. BE CAREFU NOT TO OVERTIGHTEN.
4-3. SCREW two Middle Shelf Support Posts (M15) into the predrilled holes in sides of the Front Frame Assembly (M1). MAKE SURE the soft
rubber glass pads on the Posts are facing UP before attempting to install the Middle Shelf.
4-4. ATTACH five Soft Glass Pads (M14), evenly distributed, along the top edge of the Bottom Shelf Support Bar (M1). PLACE three on the
front portion, and two on the rear portion of the Bar.
4-5. Carefully NSTALL the Bottom Glass Shelf (M6) by lowering the Shelf down onto the Glass Pads (M14).
4-6. Carefully NSTALL the Middle Glass Shelf (M7) by sliding the Shelf back into the Shelf Support Brackets (M19) in the back of the Frame Assembly
(M1), and down onto the Shelf Support Posts (M15). Make sure the Middle Glass Shelf is properly inserted into the Shelf Support Brackets, and
tighten the small screw under the Shelf Bracket to secure the Shelf into place. BE CAREFU NOT TO OVERTIGHTEN SCREWS.
NOTE (!) : There is an Adjustable Glass Pad located on the top front edge of the Front Frame (M1). TURN this Adjustable Glass Pad to adjust.
ALWAYS MAKE SURE THE STAND AND ALL SHELVES ARE LEVEL AND WELL SUPPORTED BEFORE ATTEMPTING TO PLACE ANY
COMPONENTS ON THEM.
Fig. 4-2
M6
M7
M8
M16
M15
M1
M16
!
M15 M14
M16