Bellini BRA52UX-F User manual

USER MANUAL
52cm & 75cm Undermount Rangehood
Model No. BRA52UX - FINELINE: 81476
BRA52UX-F
BRA75UX - FINELINE: 133506
BRA75UX-F
GSM Retail Australia Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: Australia 1300 373 199
For Warranty and technical queries: New Zealand 0800 764 912
www.belliniappliances.com.au
V9 January 2023

Thank you.
Thank you for choosing Bellini Appliances.
This Bellini appliance carry a 3 year in home warranty, be
sure to retain your user manual and receipt.
For all warranty and technical queries please phone:
Australia 1300 373 199
New Zealand 0800 764 912
GSM Retail Australia Pty Ltd ABN: 53 007 582 475
For Warranty and technical queries: Australia 1300 373 199
For Warranty and technical queries: New Zealand 0800 764 912
www.belliniappliances.com.au

Contents
Safety Instructions------------------------------ 2
Installation---------------------------------------- 5
Start Using your Appliance-------------------- 8
Troubleshooting--------------------------------- 8
Maintenance & Cleaning --------------------- 9
Environment Protection----------------------- 12
Warranty------------------------------------------ 13

2
SAFETYINSTRUCTIONS
Thismanualexplainstheproperinstallationanduseofyourrangehood,pleasereadit
carefullybeforeusingevenifyouarefamiliarwiththeproduct.Themanualshouldbe
keptinasafeplaceforfuturereference.
Nevertodo:
●Do not try to use the rangehood without
the grease filters or if the filters are
excessively greasy!
●Do not install above a cooktop with a
high level grill.
●Do not leave frying pans unattended
during use because overheated fats or
oils might catch fire.
●Never leave naked flames under the
rangehood.
●If the rangehood is damaged, do not
attempt to use.
●Do not flambé under the rangehood.
●CAUTION: Accessible parts may become
hot when used with cooking appliances.
●
●
The minimum distance between the
supporting surface for the cooking vessels
on the hob and the lowest part of the
rangehood. (When the rangehood is
located above a gas appliance, this
distance shall be at least 65 cm)
The air must not be discharged into a flue
that is used for exhausting fumes from
appliances burning gas or other fuels.
Alwaystodo:
●Important! Always switch off the electricity
supply at the mains during installation and
maintenance such as light bulb replacement.
●The rangehood must be installed in
accordance with the installation instructions
and all measurements followed.
●All installation work must be carried out by
a competent person or qualified electrician.
●Please dispose of the packing material
carefully. Children are vulnerable to it.
●Pay attention to the sharp edges inside the
rangehood especially during installation and
cleaning.
●Make sure the ducting has no bends
sharper than 90 degrees as this will reduce
the efficiency of therangehood.
●Warning: Failure to install the screws or
fixing device in accordance with these
instructions may result in electrical hazards.
●Warning: Before obtaining access to
terminals, all supply circuits must be
disconnected.

3
Alwaystodo:
●Always put lids on pots and pans when
cooking on a gas cooker.
●When in extraction mode, air in the room
is being removed by the rangehood.
Please make sure that proper ventilation
measures are being observed. The
rangehood removes odours from room
but not steam.
●Rangehood is for domestic use only.
●If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order
to avoid a hazard.
●This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
Alwaystodo:
●Caution: The appliance and its accessible
parts can become hot during operation. Be
careful to avoid touching the heating
elements. Children younger than 8 years
old should stay away unless they are
under permanent supervision.
●There shall be adequate ventilation of the
room when the rangehood is used at the
same time as appliances burning gas or
other fuels.
●There is a fire risk if cleaning is not
carried out in accordance with the
instructions.
●Regulations concerning the discharge of
air have to be fulfilled.
●Clean your appliance periodically by
following the method given in the chapter
MAINTENANCE.
●For safety reason, please use only the
same size of fixing or mounting screw
which are recommended in this instruction
manual.
●Regarding the details about the method
and frequency of cleaning, please refer to
maintenance and cleaning section in the
instruction manual.
●Cleaning and user maintenance shall not
be made by children without supervision.
●When the range hood and appliances
supplied with energy other than electricity
are simultaneously in operation, the
negative pressure in the room must not
exceed 4 Pa (4 x 10-5 bar).
●WARNING: Danger of fire: do not store
items on the cooking surfaces.
●A steam cleaner is not to be used.
●NEVER try to extinguish a fire with water,
but switch off the appliance and then cover
flame e.g. with a lid or a fire blanket.

4
Accessories bag
Description Picture QTY
v-flap(150) 1 pair
ST4*18mm screws 8
Installation & User Manual 1
INSTALLATION(VENTOUTSIDE)
MOUNTINGOFTHEV-FLAP
If the rangehood does not have an assembled V-flap 1, you should mount the half-
parts to its body.The images only show an example of how to mount the V-flap,
because the outlet may vary according to different models and configurations.
To mount the V-flap 1 you should:
• Mount two half-parts 2 into the body 6
• the pin 3 should be top oriented;
• the axis 4 should be inserted into the holes 5 on the body;
• repeat all the operations for the 2nd half-part
PRODUCTDESCRIPTION

5
INSTALLATION
INSTALLATION
If you have an outlet to the outside, your rangehood can be connected as below picture by
means of an extraction duct (enamel, aluminum, flexible pipe or non-flammable material with
an interior diameter of 150mm)

6
1. Before installation ensure that the cupboard is structurally sound and is capable of
carrying the weight of the rangehood and that the rangehood distance between a cooktop
and underneath the rangehood must be minimum of 600mm to a cooktop and a maximum
height of 750mm.
*If the instructions of the hob specify a greater distance than the minimum above, then that shall be the minimum height for installation
Vertical centre line
Where the range hood will be
Horizontal line Hood base
Minimum: Top of Cooktop / Trivet
Electric 600mm
Gas 650mm
Maximum:
750mm

7
3. Remove the aluminum filter and then use a screwdriver to remove the two screws on the
panel. Pry out the lamp terminal box with flat screwdriver and unplug the lamp terminal.
Finally, remove the panel.
4. Mount the rangehood on the cabinet with 8 screws (ST4 x 18mm).Then connect the lamp
terminal and cover it with lamp terminal box.
5. Secure the front panel on the rangehood body with 2 screws (M4 x 10mm). Reinstall the
aluminum filter in the rangehood.
2. The minimum requirement for the height of the inside cupboard is suggested 384mm to fit
the undermount rangehood. Make sure the distance between the edge of the cut out hole
and the back of the cupboard is at least 25mm and at least 25mm from the other cut out
edges front and sides. The cut out hole in the cabinet should measure Width*depth
490*265 (mm) for BRA52UX and715*265 (mm) for model BRA75UX. Refer pic below.
Min500
m
in25
min25
160
15 0
490/715
min25
26 5
min25
24 5
m
in500
2
0

8
Note:The expansion pipe is not included in the product.
WARNING: •For safety reason, please use only the same
size of fixing or mounting screws which are
recommended in this instruction manual.
•Failure to install the screws or fixing device in
accordance with these instructions may result
in electrical hazards.
StartUsingYourRangehood
Toggleswitch
①②
Fault PossibleCause Solution
Light on, but motor
does not work
Fan switch turned off. Select a fan switch position.
Fan switch failed. Contact service center.
Motor failed. Contact service center.
Light does not
work, motor does
not work
House fuses blown. Reset/Replace fuses.
Mains power cable is loose
or disconnected.
Refit mains power cable to
power outlet.
Switch power outlet on.
Oil leakage
One way valve and the
outlet are not tightly sealed.
Take down the one way valve
and seal with sealant.
Leakage from the connection
of chimney and cover. Take chimney down and seal.
There are 3 speeds for the motor and on/ off switch for the lamp
1.Lamp – Turn on/off light
“0” – to switch off light
“I” – to switch on light
2 .Speed – select speed to suit cooking conditions
“0” – to switch off motor
Low( I ) – light frying/boiling
Medium( II ) – frying/wok cooking/heavy boiling
High ( III ) – grilling, intensive frying and wok cooking
TROUBLESHOOTING

9
Lights not working Broken or faulty bulbs. Replace blubs as per this
instruction.
Insufficient suction
The distance between the
rangehood and the gas top
is too far.
Refit the rangehood to the
correct distance.
The rangehood
inclines
The fixing screw is not tight
enough.
Tighten the hanging screw and
make it horizontal.
NOTE:
Any electrical repairs to this appliance must conform to your local, state and
federal laws. Please contact the service centre if in any doubt before undertaking any
of the above. Always disconnect the unit from the power source when opening the unit.
MAINTENANCEANDCLEANING
Caution:
•Before maintenance or cleaning is carried out, the rangehood
should be disconnected from the mains power supply. Ensure
that the rangehood is switched off at the wall socket and the
plug removed.
•External surfaces are susceptible to scratches and abrasions, so please follow the
cleaning instructions to ensure the best possible result is achieved without damage.
GENERAL
Cleaning and maintenance should be carried out with the appliance cold especially when cleaning.
Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.) on the surfaces.
STAINLESS STEEL
The stainless steel must be cleaned regularly (e.g.weekly) to ensure a long life expectancy. Dry
with a clean soft cloth. A specialized stainless steel cleaning fluid may be used.
NOTE:
Ensure that wiping is done along with the grain of the stainless steel to prevent any unsightly
crisscross scratching patterns from appearing.
CONTROL PANEL SURFACE
The inlay control panel can be cleaned using warm soapy water. Ensure the cloth is clean and well
wrung before cleaning. Use a dry soft cloth to remove any excess moisture left after cleaning.
Important
Using neutral detergents and avoid using harsh cleaning chemicals, strong household detergents
or products containing abrasives,as this will affect the appearance of the appliance and potentially
remove any printing of artwork on the control panel and will void manufactures warranty.

10
GREASE MESH FILTERS
The mesh filters can be cleaned by hand. Soak them for about 3 minute in water with a mild
detergent and then brush it gently with a soft brush. Please do not apply too much pressure
so as to avoid any damage to it. (Leave to dry naturally out of direct sun light). Filters should
be washed separately to crockery and kitchen utensils. It is advisable not to use rinse aid.
INSTALLING GREASE MESH FILTERS
•To install filters for the following four steps:
- Angle the filter into the slots at the back of the hood.
- Push the button on the handle of the filter.
- Release the handle once the filter fits into a resting position.
- Repeat to install all filters.
CARBON FILTER-not included in the product
Activated carbon filter can be used to trap odors. Normally the activated carbon filter should be
changed every 3 to 6 months according to your cooking habits. The installation procedure of
activated carbon filter is as below.
1. Before installing or replacing the carbon filters, please disconnect mains power to the unit.
2. Press the filter lock and remove the mesh filter.
3. Turn the carbon filter on both sides of the motor anti-clockwise. Replace the carbon
filters with the new carbon filters.
4. Place the mesh filter.
5. Connect the power supply to the wall socket.
NOTE:
Make sure the filter is securely locked. Otherwise, it would loosen and cause danger.
When activated carbon filter attached, the suction power will be lowered.

11
BULB REPLACEMENT
Important : The bulb must be replaced by the manufacturer, its
service agent or similarly qualified persons.
Always switch off the electricity supply before
carrying out any operations on the appliance. When
handling bulb, make sure it has completely cooled
down before any direct contact with hands.
When handling bulbs hold with a cloth or gloves to
ensure perspiration does not come in contact with
the bulb as this can reduce the life of the bulb.
Note:
Before changing the lights, make sure that the appliance is turned off and unplugged .
Protect against danger when changing lights, such as wearing gloves.
Changing the lights:
Remove the grease filter.
Put one hand into the cavity to gently push out the LED light, and use the other hand to
grab the light and pull it out, and then pull out the light cable.
After changing the lamp, plug in the lamp cable, and press the lamp into the lamp hole.
•ILCOS D code for this lamp is: DBR-2/65-H-64
– LED modules –round lamp
–Max wattage: 2×2 W
– Voltage range: AC 110-240V
–Dimensions: 64mm

12
ENVIRONMENTALPROTECTION:

This product is marked with the symbol on the selective sorting of
waste electronic equipment. This means that this product must not
be disposed of with household waste but must be supported by a
system of selective collection in accordance with Directive
2012/19/EU. It will then be recycled or dismantled to minimize
impacts on the environment, electrical and electronic products are
potentially dangerous for the environment and human health due to
the presence of hazardous substances.For more information, please
contact your local or regional authorities.
NOTE:
The following shows how to reduce total environmental impact (e.g. energy use) of the cooking
process).
(1) Install the rangehood in a proper place where there is efficient ventilation.
(2) Clean the rangehood regularly so as not to block the airway.
(3) Remember to switch off the rangehood light after cooking.
(4) Remember to switch off the rangehood after cooking.
ININFORMATION FOR DISMANTLING
Do not dismantle the appliance in a way which is not shown in the user manual. The appliance
could not be dismantled by user. At the end of life, the appliance should not be disposed of with
household waste. Check with your Local Authority or retainer for recycling advice.

WARRANTY
1.1 In this warranty:
1.1.1 Australian Consumer Law means the law as set out in Schedule 2 of the Competition and
Consumer Act 2010;
1.1.2 Company means GSM Retail Australia Pty Ltd ABN 53 007 682 475 of 142-144 Fullarton Road, Rose
Park SA 5067. Telephone [phone]. Email [e-mail]
1.1.3 Consumer means a “consumer” as that term is defined in Section 3 of the Australian Consumer
Law as the original purchaser of a Bellini product;
1.1.4 Consumer Guarantees means the guarantees under the Australian Consumer Law;
1.1.5 You means the Consumer.
1.2 Nothing in this warranty affects any person’s rights under the Australian Consumer Law. The benefits to
any Consumer under this warranty are in addition to the rights and remedies available under any
Consumer Guarantees.
1.3 Subject to the other clauses of this warranty, the Company warrants to the Consumer that the Bellini
product will be free of manufacturing defects and will perform to the Company’s specifications.
1.4 The benefit of this warranty extends only to the Consumer as original purchaser of a Bellini product which
is installed in a domestic household area.
*The in Home warranty does not apply to Commercial and or industrial usage. *Please See 1.7.7 for additional
information
1.5 This warranty commences on the date of purchase of the Bellini product by the Consumer and
continues for the benefit only of the Consumer until the expiry of three (3) year (Warranty Period).
1.6 If within the Warranty Period a manufacturing defect is discovered in the Bellini product or it fails to perform
to the Company’s specifications as a result of some defect in materials, components or workmanship
(Defect) then the Company will, at its option, repair the Bellini product or supply a replacement Bellini
product free of charge. A replacement Bellini product may differ from the original product purchased by the
Consumer.
1.7 This warranty will not apply to any Bellini product:
1.7.1 Installed by any person other than a qualified tradesperson; or
1.7.2 Subjected to misuse, neglect, negligence or accidental damage; or
1.7.3 Operated in any way contrary to any operating or maintenance instructions; or
1.7.4 Improperly handled, installed or maintained; or
1.7.5 Altered or modified prior to or after installation; or
1.7.6 Damaged directly or indirectly by power surges, electrical storm damage or connection to incorrect
power supply
1.7.7 Industrial and or Commercial usage is inclusive of staff areas in office/ shop environments, hotel/
motel or other similar accommodation or rental type properties including Bed and Breakfast
establishments.
The Australian Consumer Law requires the inclusion of the following
statement with this warranty:
Our goods come with guaranteed that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.

1.8 You must provide proof of your purchase of the Bellini product and the date of purchase in order to obtain
the benefit of this warranty.
1.9 If you live outside the service area of the Company or one of its service agents, this warranty does not
cover the cost of transport of the Bellini product for service nor the service agent’s traveling costs to and
from your home.
1.10 If you are required to transport the Bellini product to the Company or its service agent, you must ensure it is
safely disconnected by a qualified tradesman and securely packed and insured. The Company does not
accept any responsibility for loss or damage of the Bellini product prior to it being received by the Company or
its service agent.
1.11 You will be responsible for all costs of returning a Bellini product to the Company and for redelivery of the
Bellini product by the Company (whether it is the original or a repaired and/or a replacement Bellini product)
and for any other expenses you incur in claiming under this warranty.
1.12 The Company or its service agent will examine any Bellini product and if the Company determines that it is
defective through no fault of the Owner and is otherwise undamaged, the Company will repair or replace the
Bellini product in accordance with this warranty.
DO NOT SEND IN THIS WARRANTY
Fill out the following details and file with your purchase invoice for safe keeping.
RETAIN & FILE WITH YOUR RECEIPT
Your Purchase Receipt/Invoice is proof of date of purchase. If you are unable to establish the date of purchase, or if
the fault is not covered by this warranty, or if the product is found to be in working order, you will be required to bear
all service call charges.
GSM Retail Australia Pty Ltd reserves the right to discontinue items, modify designs and change specifications
without incurring obligation.
Whilst every effort is made to ensure that descriptions, specifications and other information in this publication is
correct, no warranty is given in respect thereof and the company shall not be liable for any errors therein.
Purchased from:
Co. Name:
Address:
Date of Purchase:
Serial number:
NOTE: Consistent with our continuing product development policy, improvements may have been made which
render the contents of this packaging slightly different to that shown.
For Warranty and technical queries: Australia 1300 373 199
: New Zealand 0800 764 912