Bender PEM533 User manual

Manual
EN
PEM533
Universal measuring device
Software version 2.00.XX
PEM533_D00013_01_M_XXEN/01.2016
B 9310 0533
B 9310 0534
B 9310 0535
B 9310 0536

Bender GmbH & Co. KG
Londorfer Str. 65 • 35305 Gruenberg • Germany
Postfach 1161 • 35301 Gruenberg • Germany
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]
www.bender.de
©Bender GmbH & Co. KG
All rights reserved.
Reprinting only with permission
of the publisher. Subject to change!
Photos: Bender

3
Table of Contents
PEM533_D00013_01_M_XXEN/01.2016
1. Making effective use of this document ............................................... 7
1.1 How to use this manual ......................................................................................... 7
1.2 Technical support: Service and support .......................................................... 8
1.3 Workshops ................................................................................................................. 9
1.4 Delivery conditions, guarantee, warranty and liability ............................ 10
2. Safety ...................................................................................................... 11
2.1 Intended use ........................................................................................................... 11
2.2 Qualified personnel .............................................................................................. 11
2.3 General safety instructions ................................................................................ 12
3. Device description ............................................................................... 13
3.1 Area of application ................................................................................................ 13
3.2 Device features ....................................................................................................... 13
3.3 Versions .....................................................................................................................14
3.4 Application example ............................................................................................ 15
3.5 Description of function ....................................................................................... 16
3.6 Front view and rear view .................................................................................... 16
4. Installation and connection ............................................................... 17
4.1 Project planning ..................................................................................................... 17
4.2 Safety instructions ................................................................................................. 17
4.3 Installing the device ............................................................................................. 17
4.3.1 Dimension diagrams ................................................................................... 17
4.3.2 Front panel mounting ................................................................................ 18
4.4 Connection of the device ................................................................................... 19
4.4.1 Safety information....................................................................................... 19
4.4.2 Back-up fuses ................................................................................................. 19
4.4.3 Connection of measuring current transformers ............................... 19

Table of Contents
4PEM533_D00013_01_M_XXEN/01.2016
4.5 Instructions for connection ................................................................................ 19
4.6 Wiring diagram ....................................................................................................... 20
4.7 Connection diagram voltage inputs ............................................................... 21
4.7.1 Three-phase 4-wire systems (TN, TT, IT systems) .............................. 21
4.7.2 Three-phase 3-wire system ....................................................................... 21
4.7.3 Connection via voltage transformers ................................................... 22
4.8 Digital inputs ........................................................................................................... 22
4.9 Digital outputs ........................................................................................................ 22
5. Commissioning ...................................................................................... 23
5.1 Check proper connection ................................................................................... 23
5.2 Before switching on .............................................................................................. 23
5.3 Switching on ............................................................................................................ 23
5.4 System .......................................................................................................................24
6. Operation ............................................................................................... 25
6.1 Getting to know the operating elements .................................................... 25
6.2 LCD testing ............................................................................................................... 26
6.3 Getting to know standard display areas ....................................................... 27
6.4 Power and current demand (Demand display) .......................................... 29
6.5 LED indication ......................................................................................................... 30
6.6 Standard display .................................................................................................... 30
6.7 Data display ............................................................................................................. 30
6.7.1 "V/I" button ..................................................................................................... 31
6.7.2 "POWER" button ........................................................................................... 33
6.7.3 "HARMONICS" button ................................................................................. 35
6.7.4 "ENERGY" button .......................................................................................... 36
6.8 Setup using the button at the device ............................................................ 37
6.8.1 Setup: Function of the buttons ............................................................... 37
6.8.2 Setup: Overview diagram menu ............................................................. 37
6.9 Setup: possibilities ................................................................................................. 39
6.10 Configuration example:
Setting measuring current transformer ........................................................ 43

Table of Contents
5PEM533_D00013_01_M_XXEN/01.2016
7. Application/inputs and outputs ......................................................... 45
7.1 Digital inputs ........................................................................................................... 45
7.2 Digital outputs ........................................................................................................ 45
7.3 Display Energy pulsing ........................................................................................ 45
7.4 Power and energy ................................................................................................. 45
7.4.1 Voltage and current phase angles ......................................................... 45
7.4.2 Energy .............................................................................................................. 46
7.4.3 Demand DMD ................................................................................................ 46
7.5 Setpoints ................................................................................................................... 47
7.5.1 Control setpoints .......................................................................................... 47
7.5.2 Setpoints of the digital inputs and outputs (DI setpoint) .............. 48
7.6 Logging ..................................................................................................................... 49
7.6.1 Peak demand log ......................................................................................... 49
7.6.2 Max/Min log ................................................................................................... 49
7.6.3 Event log (SOE log) ...................................................................................... 51
7.7 Power Quality .......................................................................................................... 51
7.7.1 Harmonic distortion .................................................................................... 51
7.7.2 unbalance ....................................................................................................... 52
8. Modbus Register Map .......................................................................... 53
8.1 Basic measurements ............................................................................................. 54
8.2 Energy measurement ........................................................................................... 57
8.3 Harmonic measurements ................................................................................... 57
8.4 Demand ..................................................................................................................... 59
8.5 Extreme values per demand measurement time frame .......................... 61
8.5.1 Maximum values demand ........................................................................ 61
8.5.2 Minimum values demand ......................................................................... 63
8.6 Peak demand .......................................................................................................... 65
8.6.1 Peak demand this month .......................................................................... 65
8.6.2 Peak demand last month .......................................................................... 65
8.7 Max/Min log ............................................................................................................. 67
8.7.1 Max log of this month ............................................................................ 67
8.7.2 Min log of this month ................................................................................. 69
8.7.3 Max log of last month ................................................................................ 71

Table of Contents
6PEM533_D00013_01_M_XXEN/01.2016
8.7.4 Min log of last month .................................................................................. 73
8.8 Setup parameters .................................................................................................. 75
8.8.1 Digital input setpoint data structure .................................................... 77
8.8.2 Control setpoints data structure ............................................................. 78
8.9 Event log (SOE log) ................................................................................................ 79
8.10 Time setting ............................................................................................................. 85
8.11 DOx control .............................................................................................................. 86
8.12 Universal measuring device information ...................................................... 87
9. Technical data ........................................................................................ 89
9.1 Standards and certifications .............................................................................. 91
9.2 Ordering information ........................................................................................... 91
INDEX ............................................................................................................ 93

7
PEM533_D00013_01_M_XXEN/01.2016
1. Making effective use of this document
1.1 How to use this manual
This operating manual will concern qualified experts in electrical engineering and user
of the product and must be kept ready for referencing in the immediate vicinity of the
device.
To make it easier for you to understand and revisit certain sections of text and instruc-
tions in the manual, we have used symbols to identify important instructions and infor-
mation. The meaning of these symbols is explained below:
Although great care has been taken in the drafting of this operating manual, it may
nevertheless contain errors and mistakes. The Bender Group cannot accept any liability
for injury to persons or damage to property resulting from errors or mistakes in this
manual.
Each of the registered trademarks which appears in this document remains the
property of its owner.
The signal word indicates that there is a high risk of danger that
will result in electrocution or serious injury if not avoided.
This signal word indicates a medium risk of danger that can lead
to death or serious injury if not avoided.
This signal word indicates a low level risk that can result in minor
or moderate injury or damage to property if not avoided.
This symbol denotes information intended to assist the user to
make optimum use of the product.
DANGER
WARNING
CAUTION

Making effective use of this document
8PEM533_D00013_01_M_XXEN/01.2016
1.2 Technical support: Service and support
For commissioning and troubleshooting Bender offers you:
First Level Support
Technical support by phone or e-mail for all Bender products
 All questions about customer applications
 Commissioning
 Troubleshooting
Tel.: [phone]*
Fax: [phone]
Only available
in Germany: 0700BenderHelp (Tel. and Fax)
E-mail: [email protected]
Repair Service
Repair, calibration, update and replacement service for all Bender products
 Repair, calibration, testing and analysing Bender products
 Hardware and software update for Bender devices
 Delivery of replacement devices for faulty or incorrectly delivered Bender devices
 Extended warranty for Bender devices with in-house repair service resp. replace-
ment devices at no extra cost
Tel.: [phone]** (technical issues)
[phone]**, -785** (commercial matters)
Fax: [phone]
E-mail: [email protected]
Please send the devices for repair to the following address:
Bender GmbH, Repair Service
Londorfer Strasse 65
35305 Gruenberg
Germany

Making effective use of this document
9
PEM533_D00013_01_M_XXEN/01.2016
Field Service
On-site service for all Bender products
 Commissioning, parameter setting, maintenance, trouble shooting for Bender
products
 Analysis of the electrical installation in the building (power quality test, EMC test,
thermography)
 Practical training courses for customers
Tel.: [phone]**, -762 **(technical issues)
[phone]** (commercial matters)
Fax: [phone]
E-mail: [email protected]
Internet: www.bender.de
*Available from 7.00 a.m. to 8.00 p.m. on 365 days of the year (CET/UTC+1)
**Mo-Thu 7.00 a.m. - 8.00 p.m., Fr 7.00 a.m. - 13.00 p.m.
1.3 Workshops
Bender would be happy to provide training in respect of the use of the universal measu-
ring device.
Current dates of training courses and workshops can be found on the Internet at http:/
/www.bender.de -> Know-how -> Seminars.

Making effective use of this document
10 PEM533_D00013_01_M_XXEN/01.2016
1.4 Delivery conditions, guarantee, warranty and liability
The conditions of sale and delivery set out by Bender apply.
For software products, the "Softwareklausel zur Überlassung von Standard- Software
als Teil von Lieferungen, Ergänzung und Änderung der Allgemeinen Lieferbedin-
gungen für Erzeugnisse und Leistungen der Elektroindustrie" (software clause in
respect of the licensing of standard software as part of deliveries, modifications and
changes to general delivery conditions for products and services in the electrical
industry) set out by the ZVEI (Zentralverband Elektrotechnik- und Elektronikindustrie
e.V., the German Electrical and Electronic Manufacturers' association) also applies.
Conditions of sale and delivery can be obtained from Bender in printed or electronic
format.

11
PEM533_D00013_01_M_XXEN/01.2016
2. Safety
2.1 Intended use
The universal measuring device PEM533 is suitable for
 the analysis of energy and power
 monitoring of the power supply quality
 data recording for energy management.
As a compact device for front panel mounting, it is a replacement for analogue indica-
ting instruments. The PEM533 is suitable for 2, 3 and 4-wire systems and can be used in
TN, TT and IT systems. The current measurement inputs of the PEM are connected via
external …/1 A or …/5 A measuring current transformers. In principle, measurements
in medium and high voltage systems are carried out via measurement transformers and
voltage transformers.
Use for the intended purpose also includes:
 Device-specific settings according to local equipment and operating conditions.
 The observation of all information in the operating manual.
2.2 Qualified personnel
Only electrically skilled persons are authorised to install and commission this device.
Electrically skilled persons are those who have the relevant education, knowledge and
experience, as well as knowledge of the relevant safety standards and who are able to
perceive risks and to avoid hazards which electricity can create when work activities are
carried out on electrical installations. The electrically skilled person is specially trained
for carrying out work activities in his specific working environment and has a thorough
knowledge of the relevant standards and regulations. In Germany, an electrically skilled
person must meet the requirements of the accident prevention regulation BGV A3. In
other countries the applicable regulations have to be observed and followed.

Safety
12 PEM533_D00013_01_M_XXEN/01.2016
2.3 General safety instructions
Bender devices are designed and built in accordance with the state of the art and
accepted rules in respect of technical safety. However, the use of such devices may
introduce risks to the life and limb of the user or third parties and/or result in damage
to Bender equipment or other property.
 Only use Bender equipment:
– as intended
– in perfect working order
– in compliance with the accident prevention regulations and guidelines appli-
cable at the location of use
 Eliminate all faults immediately which may endanger safety.
 Do not make any unauthorised changes and only use replacement parts and opti-
onal accessories purchased from or recommended by the manufacturer of the
equipment. Failure to observe this requirement can result in fire, electric shock
and injury.
 Information plates must always be clearly legible. Replace damaged or illegible
plates immediately.
 If the device is overloaded by overvoltage or a short-circuit current load, it must
be checked and replaced if necessary.
 If the device is being used in a location outside the Federal Republic of Germany,
the applicable local standards and regulations must be complied with.
European standard EN 50110 can be used as a guide.
Danger of electric shock!
Touching live parts will cause danger of electric shock with fatal
consequences. All work activities on electrical installations as well as
installation activities, commissioning activities and work activities
with the device in operation may only be carried out by electrically
skilled persons!
DANGER

13
PEM533_D00013_01_M_XXEN/01.2016
3. Device description
3.1 Area of application
For humans, electric current is not immediately visible. Universal measuring devices for
monitoring electrical parameters are used wherever energy consumption, performance
measurements or the quality of the supply voltage are to be made visible.
The PEM533 is suitable for monitoring
 power generation systems (PV systems, CHPs, hydro power and wind power
plants)
 energy-intensive equipment and parts of installation
 sensitive equipment
3.2 Device features
The universal measuring device PEM533 for power quality and energy management is
characterised by the following features:
 Accuracy class in accordance withIEC 62053-22: 0.5 S
 Password protection
 9 programmable setpoints
 LED pulse outputs for active and reactive energy
 Modbus RTU communication via RS-485 interface
 6 digital inputs
 2 digital outputs
 Power and current demands for particular time frames
 Peak demands with timestamps
 Individual, harmonic components of current and voltage up to the 31st harmonic
 Max and Min values
 Measured quantities
– Phase voltages UL1, UL2, UL3 in V
– Line-conductor voltages UL1L2, UL2L3, UL3L1 in V
– Phase currents I1, I2, I3in A
– Neutral current (calculated) I4in A
– Frequency fin Hz
– Phase angle for Uand I in °
– Power per phase conductor Pin kW, Qin kvar, S in kVA

Device description
14 PEM533_D00013_01_M_XXEN/01.2016
– Total power Pin kW, Qin kvar, S in kVA
– Displacement factor cos (φ)
– Power factor λ
– Active and reactive energy import in kWh, kvarh
– Active and reactive energy export in kWh, kvarh
– Voltage unbalance in %
– Current unbalance in %
– Harmonic distortion (THD, TOHD, TEHD) for Uand I
– k-factor for I
3.3 Versions
PEM533
230/400 V, current input 5 A
PEM533-251
230/400 V, current input 1 A
PEM533-455
400/690 V, current input 5 A
PEM533-451
400/690 V, current input 1 A

Device description
15
PEM533_D00013_01_M_XXEN/01.2016
3.4 Application example
Fig. 3.1: Example of application
Modbus TCP
Ethernet
BMS
1…12
Modbus
RTU
Datenbank
L
PEN
PE
L
N
PE
U
I
Modbus TCP
Modbus RTU
PAS
PEM7xx
U
I
NSHV
UV1
1…12
RCMS
UV2
U
I
U
I
U
I
RCMS
Modbus TCP
Modbus RTU
Modbus TCP
PEM5xx PEM5xx
Modbus RTU
PEM3xx
PEM7xx
CP700
3
U
I
Modbus RTU
PEM3xx
3

Device description
16 PEM533_D00013_01_M_XXEN/01.2016
3.5 Description of function
The digital universal measuring device PEM533 is suited for measuring and displaying
electrical quantities of electricity networks. The PEM575 is able to perform current,
voltage, energy consumption and performance measurements as well as displaying
individual harmonic components of current and voltage for assessment of the voltage
and current quality.
The accuracy of the active energy metering corresponds to class 0.5 S in compliance
with the DIN EN 62053-22 (VDE 0418 Part 3-22):2003-11.
The large display of the panel mounting device makes the relevant measured quantities
easily legible and enables fast configuration. In addition, the RS-485 interface allows a
central evaluation and processing of data. Switching operations can be monitored or
initiated via the digital inputs and outputs (Example: Switching off uncritical loads if the
peak load limit value is exceeded).
The universal measuring device PEM333 provides the following functions:
 Provision of energy consumption data for a well-thought-out energy manage-
ment
 Allocation of energy costs
 Power quality monitoring for cost reduction and increased plant availability
3.6 Front view and rear view
The connecting terminals are located on the rear.
Fig. 3.2: Front view (left) and rear view (right) PEM533
kvarh
kWh
PEM533
LINETRAXX®
V/I POWER HARMONICS ENERGY
OK
DICDI1 DI2 DI3 DI4
DO13 DO14 DO23 DO24
DI5 DI6
A1 A2
Power
• l11 l12 l22 l32
L1 L2 L3 N
• l21 • l31
D+
RS-485
D
- SH

17
PEM533_D00013_01_M_XXEN/01.2016
4. Installation and connection
4.1 Project planning
For any questions associated with project planning, please contact Bender:
Internet: www.bender.de
Tel.: [phone]
4.2 Safety instructions
Only electrically skilled persons are allowed to connect and commission the device.
Such persons must have read this manual and understood all instructions relating to
safety.
4.3 Installing the device
4.3.1 Dimension diagrams
Fig. 4.1: Dimension diagram PEM533 (front view)
Danger of electric shock!
Follow the basic safety rules when working with electricity.
Consider the data on the rated voltage and
supply voltage as specified in the technical data!
DANGER
96
106
88
96
91

Installation and connection
18 PEM533_D00013_01_M_XXEN/01.2016
Fig. 4.2: Dimension diagram PEM533 (side view)
Fig. 4.3: Dimension diagram PEM533 (panel cutout)
4.3.2 Front panel mounting
A front panel cutout of 92 mm x 92 mm is necessary for installation.
1. Insert the device through the cutout in the front panel.
2. Insert the two installation clips into the equipment rail from behind.
3. Push the clips towards the front panel and tighten the associated screws by
hand.
4. Check the device to ensure that it is firmly installed in the front panel.
The device is installed.
18 88
91
18
96
92
92

Installation and connection
19
PEM533_D00013_01_M_XXEN/01.2016
4.4 Connection of the device
4.4.1 Safety information
4.4.2 Back-up fuses
Fuses supply voltage: 6 A
Short-circuit protection Protect the measurement inputs according to the require-
ments of the standards (2 A recommended). A suitable isolation means must be
provided. For details refer to the operating manuals of the measuring current transfor-
mers currently used.
4.4.3 Connection of measuring current transformers
When connecting the measuring current transformers take into account the require-
ments of die DIN VDE 0100-557 (VDE 0100-557) – Teil 5: Errichten von Niederspan-
nungsanlagen (Part 5: Low voltage installations) Auswahl und Errichtung elektrischer
Betriebsmittel - Abschnitt 557: (Selection and erection of electrical equipment - Section
557): Hilfsstromkreise (Auxiliary circuits).
4.5 Instructions for connection
 Connect the PEM533 to the supply voltage (terminals A1 and A2 resp. +/-).
Connect terminal " " to the protective conductor.
 Power protection by a 6 A fuse, quick response.
If being supplied from an IT system, both lines have to be protected by a fuse.
 Connection to the RS-485 bus is made via the terminals D+, D- and SH. Up to 32
devices can be connected to the bus. The maximum cable length for the bus con-
nection of all devices is1200 m.
Danger of electric shock!
Follow the basic safety rules when working with electricity.
Consider the data on the rated voltage and supply voltage as
specified in the technical data!
If the supply voltage Usis supplied by an IT system, both phase
conductors are to be protected.
DANGER

Installation and connection
20 PEM533_D00013_01_M_XXEN/01.2016
4.6 Wiring diagram
Connect the device according the wiring diagram. The connections are located on the
rear of the device.
Fig. 4.4: Wiring diagram
Legend to wiring diagram
1Connection RS-485 bus
2Supply voltage. Power protection by a 6 A fuse, quick response.
If being supplied from an IT system, both lines have to be protected by a fuse.
3Digital inputs
4Digital outputs (N/O contacts)
5Measuring voltage inputs: The measuring leads should be protected with
appropriate fuses.
6Connection to the system to be monitored
DICDI1 DI2 DI3 DI4
DO13 DO14 DO23 DO24
DI5 DI6
A1 A2
Power
• l11 l12 l22 l32
L1 L2 L3 N
• l21 • l31
D+
RS-485
D
- SH
L1
L1
I11
I12
I21
I22
I31
I32
L2
L2
L3
L3
N
N
DI1 DICDI5 DI6DI2 DI3 DI4
US
DO13 DO14
DO23 DO24
1
2
3
4
5
6