BenQ AR15 D Genie User manual

e-Reading Lamp
AR15_D Genie
BenQ.com
© 2021 BenQ Corporation.
All rights reserved. Rights of modification reserved.
P/N: 4J.2T004.004
4J.W3P04.004

1English
Package Contents
Check the packaging for the following items. If any is missing or damaged, please contact the place
of purchase immediately.
For Your Safety
• Use only the supplied power adapter and connect only to a suitable outlet power (100-240V
AC, 50-60 Hz). Otherwise the lamp will fail to work normally or result in a fire hazard.
• In order to prevent any damages to the lamp, do not hang or place any objects over the lamp.
• Route the power cord so as to avoid it from being walked on or pinched by items placed upon
or against it.
• Place the lamp only on a solid, flat and stable surface. Otherwise the lamp may topple over and
result in damages.
• If the lamp will not be used for a long period of time, unplug it from the power outlet.
Installation
1. Place the pedestal base on a solid,
flat and stable surface.
2. Insert the metal shaft on the lamp
body into the hole on the top of the
lamp arm [Figure ]. When
inserting, note the direction of the
shaft and ensure that the lamp body
is horizontally seated on the lamp
arm.
The convex side of the lamp arm
should face toward the direction
where the lamp head extends [Figure
(1)].
3. Secure the lamp body to the lamp
arm by tightening the two screws
using the hex L-key provided [Figure
(1)].
Press the rubber pad into the groove
to cover the screw holes [Figure
(2)].
4. Press the cable into the groove on
the lamp arm [Figure (1)].
At least 8 cm of excess length should
be left in order for the lamp body to
move freely [Figure (2)].
5. Connect the power cord to the power adapter [Figure (3)] and plug it into a power outlet
[Figure (4)].
• Genie e-Reading Lamp body x 1
• Pedestal base with arm x 1
• Hex L-key x 1
• Screw x 2
• Power adapter x 1
• Rubber pad x 1
The illustrations in this guide are for your reference only and may look different from the
appearance of the product you purchased.
In case of the following situations, unplug the lamp from the power outlet
immediately and contact the authorized service center or a qualified service
person for inspection or repair:
• When the outer casing of the lamp is broken
• When there are strange odors coming from the lamp
• When the lamp flickers
• When the insulation of the lamp’s wiring is damaged or frayed, and the metal
strings inside can be seen
Do not use the lamp in a humid environment (like in a bathroom or outdoors).
Otherwise the components inside may short-circuit and result in accidents.
This lamp is designed for indoor use only. Do not use it outdoors.
Never disassemble the lamp or remove any components from it, as doing so may
result in accidents and will void the product warranty.
CAUTION
> 8cm
> 8cm

2English
Using the Lamp
Identifying the Model of Your Lamp
Using the Model with Dual Auto-Dimming Mode
Turning On/Off the Lamp
Adjusting Brightness and Color Temperature
The lamp provides one Manual lighting mode that allows you to adjust the brightness and color
temperature manually and two Auto lighting modes for use in two different situations.
Adjusting Brightness and Color Temperature Manually Using the Manual Lighting
Mode
Check if the sticker is there on the metal ring of the
lamp.
• If yes, then you are using the model with dual auto-dimming
mode. Refer to "Using the Model with Dual Auto-Dimming
Mode" below for instructions.
• If no, then you are using the standard model. Refer to "Using
the Standard Model" on page 3 for instructions.
To turn on the lamp, gently touch the metal ring on the lamp.
To turn off the lamp, touch the metal ring again. You can also
turn the lamp on by pressing the knob on the lamp.
Lighting mode Setting Lighting mode
indicator color
Color temperature Brightness level
Manual Adjustable Adjustable None (off)
Auto Book reading 5700K Automatically optimized according to ambient
lighting condition
Orange
Digital reading 4000K Green
• When the lamp is on, turn the knob on the lamp [Figure
] clockwise to increase brightness, or counter-clockwise
to decrease it.
• When the lamp is on, press the knob on the lamp [Figure
] to switch to the color temperature menu. Then, turn
the knob clockwise to increase color temperature (the light
becomes whitish), or counter-clockwise to decrease it (the
light becomes yellowish).
To switch back to the brightness menu, press the knob on the
lamp again.
1
2

3English
Using the Standard Model
Turning on/off the Lamp and Entering Eye-care Mode
Adjusting Brightness and Color Temperature
Using the Auto Lighting Modes
• To enter the Auto - Book reading mode, touch and hold the
metal ring on the lamp [Figure ] for approximately 2
seconds when the lamp is on. The Lighting mode indicator
will light up orange. To switch to the Auto - Digital reading
mode, touch and hold the metal ring on the lamp for
approximately 2 seconds again, and the Lighting mode
indicator will light up green.
• The Auto lighting modes protect your eyes by adjusting the
lamp’s brightness automatically according to the ambient
lighting condition detected by the Ambient light sensor
[Figure ] and optimizing the color temperature settings
for book and digital reading.
• Do not block the Ambient light sensor on the lamp.
Otherwise the Auto lighting modes will not function
properly.
• Do not hold the metal ring when adjusting the angle of the
lamp arm.
• The Auto lighting modes will exit automatically and the
Lighting mode indicator will go off if you manually adjust the
brightness and/or color temperature using the knob on the
lamp.
• To turn on the lamp, gently touch the metal ring on the lamp.
To turn off the lamp, touch the metal ring again. You can also
turn the lamp on by pressing the knob on the lamp.
• To enter Eye-care Mode, touch and hold the metal ring on
the lamp for approximately 2 seconds when the lamp is on.
The Eye-care Mode indicator will light up green. The Eye-
care Mode protects your eyes by adjusting the lamp’s
brightness according to the ambient lighting condition
automatically and optimizing the color temperature settings
for screen reading.
• Do not block the Eye-care sensor on the lamp. Otherwise the
Eye-care Mode will not function properly.
• Do not hold the metal ring when adjusting the angle of the
lamp arm.
• The Eye-care Mode will exit automatically and the Eye-care
Mode indicator will go off if you manually adjust the
brightness and/or color temperature using the knob on the
lamp.
Lighting mode
indicator
Ambient
light
sensor
Eye-care sensor
Eye-care Mode
indicator
• When the lamp is on, turn the knob on the lamp clockwise
to increase brightness, or counter-clockwise to decrease it.
• When the lamp is on, press the knob on the lamp to switch
to the Color Temperature adjustment. Turn the knob
clockwise to increase color temperature (the light becomes
whitish), or counter-clockwise to decrease it (the light
becomes yellowish).
To switch back to the Brightness adjustment, press the knob
on the lamp again.

4English
Adjusting Angle
Maintenance and Troubleshooting
Turn off the lamp first, and unplug the lamp from the power outlet. Wipe any smears or dusts off
the lamp’s outer casing using a soft, lint-free cloth lightly moistened with a mild detergent
solvent. Do not use alcohol or any other chemical solvents like kerosene, naphtha and so on, as
the lamp’s casing may become damaged.
Do not rinse the lamp or any of its components directly with water.
If the lamp does not turn on, check to make sure that there are no loose connections between
the power cord, power adapter, and the power outlet.
If the problem persists, please contact the original place of purchase for help.
Specifications
You can adjust the angle of the lamp arm according to your
desktop space to obtain a suitable lighting effect.
45°
Model AR15_D
DC power input 12V, 1.5A
Max. power consumption 18W
Dimensions (Refer to the illustration below)
44.5 cm
(17.5 in)
20 cm
(7.9 in)
8.5 cm
(3.3 in)
(15.2 in)
38.5 cm
(2 in)5.2 cm