Better Homes and Gardens Autumn Lane Series User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Furniture Mfg., Inc. Page 1 Factory: CTHAUP
Date 2014-05-31 Rev. 2
Autumn Lane 5-pc Dining Set
Stock # BH44-084-499-03
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions and
parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [email protected]
LOT NUMBER:
DATE OF PURCHASE: / /

Stock # BH44-084-499-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 2 Factory: CTHAUP
MANUFACTURER: Whalen Furniture Mfg., Inc.
CATALOG: Autumn Lane 5-pc Dining Set (BH44-084-499-03)
DATE OF MANUFACTURE: June 2014
MADE IN MALAYSIA
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware and parts out of the reach of children.
4. Please wait until all steps are completed before fully tightening bolts.
5. Make sure all nuts, bolts and screws are tightly fastened before the unit is used.
6. Check that all bolts and screws are tight at least every 3 months or as needed.
GENERAL INFORMATION, TIPS & TRICKS
MAXIMUM RECOMMENDED WEIGHT LOADS
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.
MAXIMUM LOAD 400 lb. (181.4 kg)
MAXIMUM LOAD 300 lb. (136.1 kg)

Stock # BH44-084-499-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 3 Factory: CTHAUP
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are
present before beginning assembly.
A- Chair Backrest (4) C- Seat (4) B- Chair Front Leg (8)
D- Table Top (1) E- Table Leg (4)
(1) M6 x 35 mm Bolt (2) M6 x 75 mm Bolt (3) Small Lock Washer
(12+1 extra) (16+1 extra) (28+1 extra)
(4) Small Flat Washer (5) Large Hex Nut (6) Large Lock Washer
(28+1 extra) (24+2 extra) (24+2 extra)
(7) Large Flat Washer (24+2 extra) T-handle Wrench (1) Open Wrench (2)
Tools required: Allen wrench and open wrench (provided) and Phillips screwdriver (not provided).

Stock # BH44-084-499-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 4 Factory: CTHAUP
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts. Assembly the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Place the Table Top (D) upside down on a level and protective surface, as shown above. Remove the
additional wood blocks attached at the corners by unscrewing the wood screws. These are used for
shipping purposes only. After removing them, please discard.
D
DO NOT fully tighten the bolts or nuts initially until all the bolts or nuts are
ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the nuts or bolts.

Stock # BH44-084-499-03
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 5 Factory: CTHAUP
Assembly Instructions
3. Remove the plastic caps from the hanger bolts of the Table Legs (E).
4. Attach 4 Table Legs (E) to the apron corners of the Table Top (D) by inserting the pre-attached hanger
bolts through the drilled holes on corner blocks, and fit the Large Flat Washer (7), Lock Washer (6) and
Hex Nut (5) onto each hanger bolt. Securely tighten the Nuts with the provided Open Wrench.
5. Ask for assistance to lift the unit upright and position it at the desired location.
567
EE
D
E
E
E
E
D
Large Lock Washer
(8 used in this step)
⑥
Large Hex Nut
(8 used in this step)
⑤
Large Flat Washer
(8 used in this step)
⑦