Better Homes and Gardens Canton BHS3025004002 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2023-04-25 Rev. 0001-A
Canton End Table
Stock # BHS3025004002
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /
O
R

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Canton End Table
MODEL # BHS3025004002
SPECIAL NOTE
Please read the instruction sheets completely before assembly. Examine all packaging
material before discarding carton. Remove any remaining staples from the carton before
discarding. Remove all parts from carton and separate into groups as indicated on part
list. Please ensure all parts are included prior to assembly. Use of power tools to
complete assembly is not recommended.
M A X I M U M R E C O M M E N D E D
W E I G H T
L
O A D
S
MAXIMUM LOAD 50 lb. (22.7 kg)
MAXIMUM LOAD 50 lb. (22.7 kg)
MAXIMUM LOAD 20 lb. (9.1 kg)
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.

3
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-
abrasive surface. You will need the parts identified on page 6 and 7 of this instruction manuals.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
You are now ready to assemble the KD unit.
GLUE
FINAL
1 2 43
13

4
FURNITURE POWER DISTRIBUTION CENTER
IMPORTANT SAFETY INSTRUCTIONS
Carefully read all instructions installing and operating fixture
IF YOU HAVE ANY QUESTIONS REGARDING THE PROPER INSTALLATION
CONSULT A QUALIFIED ELECTRICIAN.
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR
INJURY TO PERSONS, PLEASE FOLLOW THE NEXT:
 Use only insulated staples or plastic ties (not included) to secure the cords.
 Route and secure cords so that they will not be pinched or damaged when the desk is pushed up against
the wall.
 Make sure cord is not pinched between desk and floor.
 Use the unit indoors only.
 Do not use an extension cord to connect this unit to a wall outlet.
 Use power strip with integral over-current protection to supply other electrical devices or accessories in
table.
 This unit must be plugged into a properly grounded outlet.
 The socket outlet should be installed near the equipment and should be easily accessible.
 Maximum load of connected equipment cannot exceed a total of 2.1 amps and 5 volts.
 Do not open or disassemble this unit for any reason.
SAVE THESE INSTRUCTIONS

5
Furniture Power Distribution Unit User Guide
Please read this user guide before installing and using your power distribution Center.
INTRODUCTION
The integrated USB center can connect to two devices, such as a digital camera, MP3 player, cell phone or
wireless mouse.
SPECIFICATIONS
Input: 100 ~ 240 V, 0.3 A, 50/60 Hz, USB output: 5 V dc, 2.1 A MAX
NOTES
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAN ICES-003(B) / NMB-003(B)
This Class B digital apparatus complies with Canadian ICES-003.
Whalen Furniture Manufacturing
1578 Air Wing Road, San Diego, CA 92154, USA
1-866-942-5362
WARNINGS
! Keep your USB hub dry; if it gets wet, wipe it dry immediately.
! Do not modify or tamper with your USB hub’s internal components. It may cause a malfunction and
invalidate its warranty.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could
void user’s authority to operate the equipment.
Product: Furniture Power Distribution Unit
Model No: GEO101U-050210U
Company: Whalen Furniture Manufacturing

6
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel (Qty. 1) B- Left Side Panel (Qty. 1) C-Right Side Panel (Qty. 1)
D- Back Panel (Qty. 1) E- Bottom Panel (Qty. 1) F- Front Crossbar (Qty. 1)
G- Front / Back Skirting (Qty. 2) H- Adjustable Shelf (Qty. 1) I- Door (Qty. 1)
J- Drawer Front Panel (Qty. 1) K- Drawer Back Panel (Qty. 1) L- Drawer Left Side Panel (Qty. 1)
M- Drawer Right Side Panel (Qty. 1) N- Drawer Bottom Panel (Qty. 1)

7
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Small Cam Lock (2) Large Cam Lock (3) Cam Bolt (4) M5 x 30 mm Wood Dowel
(Qty. 4+1 extra) (Qty. 22+1 extra) (Qty. 26+1 extra) (Qty. 4+1 extra)
(5) M8 x 30 mm Wood Dowel (6) M3 x 12 mm Screw (7) M3.5 x 30 mm Screw (8) Knob
(Qty. 22+1 extra) (Qty. 2+1 extra) (Qty. 4+1 extra) (Qty. 2)
(9) 5/32” x 12 mm Bolt (10) 5/32” x 22 mm Bolt (11) M3.5 x 15 mm Pan Head Screw (12) Triangle Metal Plate
(Qty. 1) (Qty. 1) (Qty. 16+1 extra) (Qty. 4)
(13) Floor Leveler (14) Shelf Pin (15) Hinge (16) M3.5 x 15 mm Flat Head Screw
(Qty. 4) (Qty. 4+1 extra) (Qty. 2) (Qty. 4+1 extra)
(17) Cam Lock Cover (18) Rubber Bumper (19) USB Hub with Adapter
(Qty. 6+1 extra) (Qty. 2+1 extra) (Qty. 1)
Glue Touch-up Pen Tipping Restraint Hardware Kit
(Qty. 1) (Qty. 1) (Qty. 1)
Tools required: Phillips screwdriver, stud finder, pencil, tape measure, power drill and 1/8”drill bit, and rubber
mallet (not provided).

8
Assembly Instructions
NOTE: Please do not fully tighten all screws and bolts until you finish assembling all parts. Once
assembled, go back and fully tighten all screws and bolts. This will make the assembly easier.
1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a
carpeted floor or the empty carton to avoid any scratch.
2. Securely screw four Cam Bolts (3) into the designated small holes on the Drawer Front Panel (J) with a
Phillips screwdriver. DO NOT overtighten the Cam Bolts.
NOTE: Screw-in cam bolts must be screwed down flush.
J
3
3
③ x 4

9
Assembly Instructions
3. Glue four Small Wood Dowels (4) into the inner holes on the Panels (K, L and M). Make sure that you
use a small amount of glue with both ends of all dowels.
NOTE: It is very important to use a small amount of glue on both ends of dowels and wipe off the
excess glue immediately with a damp cloth.
44
4
K
LM
4
4
④ x 4

10
Assembly Instructions
4. Insert four 30 mm Screws (7) through the Drawer Side Panels (L and M) and screw into the Drawer Back
Panel (K).
K
7
7
L
M
Grooves line up with each
other and face inward
⑦ x 4

11
Assembly Instructions
5. Slide the Drawer Bottom Panel (N) into the grooves on the Drawer Side Panels (L and M) until fully
inserted into the Drawer Back Panel (K).
NL
M

12
Assembly Instructions
6. Using the wood dowels as a guide, align and attach the Drawer Front Panel (J) to the Drawer Side Panels
(L and M) by engaging four Small Cam Locks (1). (Refer to page 3 on Cam Lock system operation
supplement).
L
M
J
1
① x 4

13
Assembly Instructions
7. Attach one Knob (8) to the outside of the Drawer Font Panel (J) with one 12 mm Bolt (9).
J
⑧ x 1 ⑨ x 1

14
Assembly Instructions
8. Securely screw eight Cam Bolts (3) into the designated small holes on the Top Panel (A) and Bottom Panel
(E) with a Phillips screwdriver.
③ x 8
E
A
3

15
Assembly Instructions
9. Securely screw ten Cam Bolts (3) into the designated small holes on both Side Panels (B and C) with a
Phillips screwdriver.
③ x 10
B
C
3

16
Assembly Instructions
10. Glue eight Large Wood Dowels (5) into the inner holes on the Panels (B, C and E).
⑤ x 8
B
C
E
5
5
5

17
Assembly Instructions
11. Glue the Large Wood Dowels (5) into the designated holes on the Back Panel (D), Front Crossbar (F) and
both Skirting Boards (G).
5
5
5
55
D
GG
F
⑤ x 14

18
D
E
2
Assembly Instructions
12. Using the wood dowels as a guide, orient and attach the Back Panel (D) to the Bottom Panel (E) by
engaging two Large Cam Locks (2).
② x 2
The cutout for USB hub
The cam lock housings face
inward for nice looking

19
Assembly Instructions
13. Align and attach the Right Side Panel (C) to the right side of the previous assembly by engaging four Large
Cam Locks (2).
② x 4
DE
C
2
2

20
Assembly Instructions
14. Orient and attach the Front Crossbar (F) to the Right Side Panel (C) by engaging one Large Cam Lock (2).
C
F
2
② x 1
The cam lock housings face
inward for nice looking