Better Homes and Gardens Oaklee BHS3025004001 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2023-01-10 Rev. 0001-A
Oaklee Media Console
Stock # BHS3025004001
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions and
parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
IMPORTANT
Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and
non-abrasive surface. You will need the parts identified on page 3 and 4 of this instruction manuals.
NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED
OFF WITH DAMP CLOTH.
Insert the dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.
CAM LOCK SYSTEM OPERATION
HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS
1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam
Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.
2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam
Lock faces out and points towards Cam Bolt.
3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.
4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.
How to adjust the Euro-style adjustable hinges on doors
Shipping may cause doors to become out of alignment. If you find that the doors need to be
adjusted slightly, turn the appropriate screw as illustrated below.
1. TO ADJUST THE DOOR FORWARD OR BACKWARD.
2. TO ADJUST THE DOOR TO RIGHT OR TO LEFT.
3. TO ADJUST THE DOOR UP OR DOWN.
1234
GLUE
FINAL
1 2 43
13
12
3

3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Panel B- Media Shelf
(Qty. 1) (Qty. 1)
C- Bottom Panel D- Left Side Frame
(Qty. 1) (Qty. 1)
E- Right Side Frame F- Upper Partition Panel G- Lower Partition Panel
(Qty. 1) (Qty. 1) (Qty. 2)
H- Door I- Small Adjustable Shelf J- Large Adjustable Shelf
(Qty. 2) (Qty. 2) (Qty. 1)
K- Back Panel L- Support Foot M- Stop Rail
(Qty. 1) (Qty. 1) (Qty. 1)

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
(1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel
(Qty. 24+1 extra) (Qty. 24+1 extra) (Qty. 24+1 extra)
(4) M3.5 x 15 mm Washer Head Screw (5) Door Stopper (6) M3 x 15 mm Screw
(Qty. 36+1 extra) (Qty. 2) (Qty. 4+1 extra)
(7) Shelf Pin (8) Handle (9) 5/32” x 25mm Handle Bolt
(Qty. 12+1 extra) (Qty. 2) (Qty. 4+1 extra)
(10) Cam Lock Cover Glue Touch-up Pen Tipping Restraint Hardware Kit (Qty.2)
(Qty. 32+1 extra) (Qty. 1) (Qty. 1) (Included in plastic bag)
Tools required (not provided): Phillips’s screwdriver, stud finder, tape measure, pencil, power drill and 1/8”
drill bit.

5
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts listed. Assemble the unit
on a carpeted floor or the empty carton to avoid any scratches.
2. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A) and Side Frames
(D and E) using a Phillips screwdriver.
NOTE: Screw-in cam bolts must be screwed down flush.
② x 14
2
A
E
D

6
2
C
B
Assembly Instructions
3. Securely screw the Cam Bolts (2) into the designated small holes on the Media Shelf (B) and Bottom
Panel (C).
② x 8

7
⑥ x 4
Assembly Instructions
4. Using the pilot holes as a guide, fasten two Door Stoppers (5) to the Media Shelf (B) using four 15 mm
Flat Head Screws (6).
5
6
B
B
⑤ x 2

8
Assembly Instructions
5. Glue the Wood Dowels (3) into the inner holes on the Media Shelf (B) and Bottom Panel (C) at both
ends.
NOTE: It is very important to use a small amount of glue on both ends of dowels and wipe away the
excess glue immediately.
③ x 8
C
B
3
3

9
Assembly Instructions
6. Glue the Wood Dowels (3) into the inner holes on the Side Frames (D and E) and Partition Panels (F
and G) as shown.
③ x 16
E
D
GG
F
3
3

10
Assembly Instructions
7. Orient and attach the Lower Partition Panels (G) to the Media Shelf (B) by engaging 4 Cam Locks (1).
(Refer to page 2 on Cam Lock system operation supplement)
① x 4
G
G
B
1
Raw edge
The cam locks face outside
The cam locks face outside

11
Assembly Instructions
8. Orient and attach the Bottom Panel (C) to the Lower Partition Panels (G) with 4 Cam Locks (1).
G
G
C
1
① x 4

12
Assembly Instructions
9. Align the large holes on Left Side Frame (D) with the inserted wood dowels on the previous assembly.
Firmly press them together and fasten it into place with 4 Cam Locks (1).
10. Repeat the same procedure to attach the Right Side Frame (E) at the other end.
① x 8
C
B
D
E
1

13
Assembly Instructions
11. Securely screw two Cam Bolts (2) into the designated small holes on the surface of the Media Shelf (B)
using a Phillips screwdriver.
2
B
② x 2

14
Assembly Instructions
12. Attach the Upper Partition Panel (F) to the Media Shelf (B) by engaging 2 Cam Locks (1).
B
F
1
① x 2

15
Assembly Instructions
13. Place the Top Panel (A) onto the inserted Wood Dowels (3) on the vertical panels properly and fasten it
in place with 6 Cam Locks (1).
① x 6
F
E
D
A
1

16
Assembly Instructions
14. Now, go back and securely tighten all the cam locks and screws. Make sure that all the parts are tight
and there are no gaps between the parts. This will help keep the unit square.
15. Unfold the Back Panel (K) and align the pre-drilled holes against the long edge with the pilot holes on
the back rail of Top Panel (A). And attach it in place with the provided 15 mm Washer Head Screws (4).
NOTE: We recommend attaching back panel with washer head screws at the corners first.
④ x 36
K
4
E
C
K
A
D
The adhesive tape
face
s
out
ward
.

17
Assembly Instructions
16. Securely screw the Support Foot (L) into the threaded insert on the Bottom Panel (C) and set the floor
leveler to the correct height.
C
L

18
Assembly Instructions
17. Ask for assistance to lift the assembled unit upright and position it near the final location.
18. Attach one Handle (8) to the front of each Door (H) with two 25 mm Bolts (9) per handle.
19. Pick up one Door (H) and attach the extended hinge arms to the hinge bases installed on the Left Side
Frame (D). Loosen the bolt on the back of hinge base for an easy fit. Align and insert the “U” slot on
hinge arm under the bolt head on the back of hinge base. Make sure that both door hinges engage and
function properly. Tighten the bolt on the hinge base to lock the hinges in place.
20. Repeat the same procedure to attach the other Door (H) to the Right Side Frame (E).
21. Open and close the doors to make sure they are aligned and shut correctly. If necessary, adjust the
screws for a good fit. Refer to the hinge sticker on door for adjustment.
1
2
1
2
E
D
H
H
8
9
9
⑧ x 2
⑨ x 4

19
Assembly Instructions
22. Insert four Shelf Pins (7) into the holes at the desired height inside each lower compartment. Tilt and
rest the Adjustable Shelves (I and J) onto the Shelf Pins (7).
I
J
I/J
7
I
7
⑦ x 12

20
Assembly Instructions
23. Plug the Cam Lock Covers (10) onto the visible cam locks to conceal the cams.
⑩ x 32
10