Bettersafe Weight Angel User manual

I n s t a l l a t i o n & T e c h n i c a l M a n u a l
S e p t e m b e r 2 0 1 9 R e v 3 . 1
I n s t a l l a t i o n &
Te c h n i c a l M a n u a l
S e p t e m b e r 2 0 1 9
R e v i s i o n 3 . 1

I n s t a l l a t i o n & T e c h n i c a l M a n u a l
S e p t e m b e r 2 0 1 9 R e v 3 . 1
2
It is imperative that the contents of this manual are read and understood b all potential users of
the fall protection s stem. The contents of this manual are intended as a reference guide for
operatives that have received the relevant training for using the fall protection s stem.
This Manual contains safet information and instructions for installing the Weight Angel Safet
s stem and should be stored in an area where it is accessible to installers and la out designers of
the s stem.
Continued improvement and advancement of product design ma have caused changes to the
current Weight Angel Safet S stem, which are not included in this Manual.
Whenever a question arises regarding the Weight Angel, or this Manual, please consult the
Bettersafe International website at www.bettersafeinternational.com for the latest available
information.
Testing and Conformit
Weight Angel complies with the current standards and requirements:
•CE to EN 795 T pe E
Introduction
General Information
WARNING!
WARNING!WARNING!
WARNING!
•This manual is invalid if an unauthorised alteration has occurred.
•Unauthorised use of this manual ma lead to prosecution
•This manual was, to the best of our knowledge, correct at its date of issue.
•It is the user’s responsibilit to ensure that all subsequent authorised amendments are incorporated
and that the manual is to the current issue status.
•A manual that is not to the latest issue status is invalid and must not be used.

I n s t a l l a t i o n & T e c h n i c a l M a n u a l
S e p t e m b e r 2 0 1 9 R e v 3 . 1
3
IMPORTANT SAFETY INFORMATION
Do not install the Weight Angel Safet S stem unless ou have read and understand the
instructions and warnings in all Manuals and have been authorised b Bettersafe International to
do so.
•Work at Height should not be attempted b a “lone” worker
•All fall protection s stems are subject to an annual test and inspection.
•This is required under EN795 and PPE Regulations
•Before each use, all preliminar inspections should be carried out as stated in their end user training.
•The manual is NOT intended as a substitute for training.
•Failure to follow the instructions or heed the warnings or improper operation could result in injur or death. WARNING: You must
consult our doctor if there is an reason to doubt our fitness to safel absorb the shock from a fall arrest. Age and fitness levels have
implications on a worker’s abilit to withstand falls. Pregnant women or minors must not use the s stem under an circumstances.
•Users must be capable of lifting 24kg safel . Muscular Injur from lifting not in accordance with local Manual Handling regulations is
possible.
•Do not tamper with or make an alterations to the Weight Angel Safet S stem.
•The Weight Angel Safet S stem shall not be used outside its limitations as described in this Manual, or for an purpose other than that
for which it is intended.
•The operation and maintenance of the Weight Angel Safet S stem must compl with the work safet laws of the jurisdiction in which it
is used. Compliance ma include the requirement for a Risk Assessment or Fall Hazard Surve Report.
•Onl competent individuals who have been given appropriate training (or who are under the immediate responsibilit of a proficient
supervisor) should use this safet equipment. In addition, the user must also be aware of the characteristics, application limits and
consequences of the incorrect use of the equipment.
•A full bod harness suitable for fall-arrest is the onl acceptable bod holding device that can be used with the Weight Angel Safet
S stem.
•Suitable Fall Arrest or Restraint equipment tested to the relevant CE standard must be used to connect the harness to the Weight Angel
to limit the load to 6kN per user.
•Operators must carr out a Pre-Use Check of the equipment to ensure that it is in a serviceable condition and operates correctl before
it is used.
•It is essential for safet that equipment is withdrawn from use immediatel should an doubt arise about its condition for safe use.
•Do not remove the labels from the Weight Angel Safet S stem.
•Do not tamper with or alter the Weight Angel in an wa unless instructed to do so b the manufacturer or authorised representative.
•For protection of one person onl .
•A rescue plan shall be in place to deal with an emergencies that could arise during the work
•SHARP EDGES: Avoid working where the connecting subs stem (i.e. full bod harness, lan ard, self-retracting lifeline etc.) or other
s stem components will be in contact with, or scrape against, unprotected sharp edges. If it is unavoidable to use the S stem near sharp
edges, ensure adequate protection against cutting is provided b using a heav pad (or similar) whilst working over the exposed sharp
edge.
•SWING FALLS: Swing falls occur when the anchorage point is not directl above the point where a fall occurs. The force of striking an
object while swinging can be great and ma cause serious injur . Also in a swing fall situation, the total vertical fall distance of the user
ma be greater than if the user had fallen verticall (directl below the anchorage point). Therefore, there will be an increase in the total
free fall distance and the distance needed to arrest the fall will increase. Swing falls can be minimised b using an anchorage point,
which is located directl above the user’s working zone.
Introduction
General Information

I n s t a l l a t i o n & T e c h n i c a l M a n u a l
S e p t e m b e r 2 0 1 9 R e v 3 . 1
4
The Weight Angel Safet S stem is designed with the following limitations:
•Fall Arrest for one user.
•Maximum roof pitch of five (5) degrees
•The roof area must be capable of retaining the at least twice weight of the Weight Angel in the
area required.
•Roofing Materials
•Single Pl Membrane
•Single Pl Bitumen Membrane with stone covering
•Single Pl Membrane Bitumen
•Concrete Deck
•Weather
•Wet surfaces are tested
•Dr surfaces are tested
•Edge Distance
•No Parapet 1000mm
•Parapet 600mm
Introduction
Installation Limitations

I n s t a l l a t i o n & T e c h n i c a l M a n u a l
S e p t e m b e r 2 0 1 9 R e v 3 . 1
5
1. The Weight Angel Safet S stem is suitable for use with the following products
i. Full Bod Harness conforming to EN361
ii. Self Retracting Lifelines conforming to EN360 and sharp edge testing
iii. Adjustable Lifelines conforming to EN353
iv. Horizontal single span lifelines conforming to EN795 Class C
v. Rescue Equipment and Descent controllers conforming to relevant EN standards
2. The Weight Angel Safet S stem should onl be used b a maximum of
•Fall Arrest: one (1) user at an one time.
•Fall Restraint: two (2) users at an one time.
3. Care should be taken to onl use karabiners and hooks that will not interact with each other
and cause forced roll out. A screw gate t pe karabiner is recommended.
4. Installation via the following instructions must be performed completel prior to use.
5. Before each use, the user must examine the equipment to ensure it is in perfect operating
condition. It is important to check for deformation, corrosion, sharp edges and abrasive areas
on the metal and absorbing parts of the s stem or component.
6. If the s stem or one of its components fails the above visual check, it should be immediatel
removed from service. Onl competent and skilled persons ma decide on the possibilit of
return to service and this permission should alwa s be given in writing.
7. Prior to a fall arrest s stem being used, it is essential to check the clearance under the user’s
working zone to prevent a collision with an obstacle or the ground in case of fall.
Introduction
User Notes

I n s t a l l a t i o n & T e c h n i c a l M a n u a l
S e p t e m b e r 2 0 1 9 R e v 3 . 1
6
S stem components
When components are required, please contact Bettersafe International quoting relevant
part number from the list. Guidance is provided in the component explanator notes.
Orders should be sent to [e-mail]
Amendments
1. Bettersafe International reserve the right to continuall update their range of products and
manufacturing processes, in the interests of reliabilit , durabilit and performance
2. In this respect, this installation and servicing manual will need occasional updating. Bettersafe
International shall issue all registered holders the relevant amendments.
3. If in an doubt regarding the current Issue Status of a manual, please contact Bettersafe
International.
Ordering S stem Components & Tools
General Information

I n s t a l l a t i o n & T e c h n i c a l M a n u a l
S e p t e m b e r 2 0 1 9 R e v 3 . 1
7
Foreword
The nature of the following text is instructional on the installation attachment of the Weight Angel
S stem. Selection of structural locations must be made b the competent Engineer in charge of the
s stem installation. A competent engineer is defined as: -
‘A person who has a recognised Structural or Civil Engineering qualifications, and who has had
adequate previous installation experience.’
This manual does not automaticall infer design approval to or for particular s stem configurations.
This must be obtained from architectural or site authorit as appropriate, before commencement of
work.
Pre-requisite Installation requirements
Installation cannot take place until the following have been full considered and completed.
Site Plan
A site plan must be drawn up to indicate the Weight Angel S stem configuration, to include: -
•Locations
•Extremities
•Entr / exit access points
•Roof surface angle
•Direction of Installation
•Obstacles.
Installation
General Information

I n s t a l l a t i o n & T e c h n i c a l M a n u a l
S e p t e m b e r 2 0 1 9 R e v 3 . 1
8
Insert the rod assembl into the base of the weight and la on the mat. Repeat
this for the 4 lower weights.
Installation
Process
La the mat in the location where the Weight Angel is required to be installed.

I n s t a l l a t i o n & T e c h n i c a l M a n u a l
S e p t e m b e r 2 0 1 9 R e v 3 . 1
9
Stack the remaining 8 weights onto the bolt
Installation
Process
Use the Post mounting frame to locate and align the lower weights, then remove
the frame.

I n s t a l l a t i o n & T e c h n i c a l M a n u a l
S e p t e m b e r 2 0 1 9 R e v 3 . 1
10
Installation
Process
Place the post mounting frame onto the bolts, and secure with the supplied nuts
and washers.

I n s t a l l a t i o n & T e c h n i c a l M a n u a l
S e p t e m b e r 2 0 1 9 R e v 3 . 1
11
Technical
Dimensions
1200
1200
300
465

I n s t a l l a t i o n & T e c h n i c a l M a n u a l
S e p t e m b e r 2 0 1 9 R e v 3 . 1
12
Technical
Weights & Materials
KEY SPECIFICATIONS
Weight 300 kg
Individual Weights 24 kg
Qt Weights 12 units
Weight of posts /supports 12 kg
Width 1200 mm
Height 465 mm
Made from Rec cled Materials
Elastomer Natural
Colour Black
Qualit Commercial
Grade N02
Hardness 70° shore a
S.G. 1.55g/cm³
Tensile MPA 4
Elongation 300%
Tear strength 12 kg/cm
Compression set 43%
Abrasion resistance 48/0 mm³
Operating temperature -20° / +70° c
MATTING SPECIFICATIONS
MATERIALS
Post Pol urethane & SS316
E e Ring SS 316
Cover Aluminium
Bolts SS 316
Frame Galvanised Steel

I n s t a l l a t i o n & T e c h n i c a l M a n u a l
S e p t e m b e r 2 0 1 9 R e v 3 . 1
[e-mail]
www. bettersafeinternational.com
NETHERLANDS
Azewijnseweg 12 SF
4214 KC
Vuren
t | + 31(0) 183 820 280
UK
Riverside, Mountbatten Wa
Congleton
Cheshire, CW12 1DY
t | + 44 (0) 1260 217 437