Beulux C92-6ZR User manual

RF Dual Color Remote Controller
Function introduction
Important: Read All Instructions Prior to Installation
Output RF signal
Operation Frequency 869.5/916.5/434MHz
Operating temperature 0-40°C
Relative humidity 8% to 80%
Dimensions 140x48x17mm
Front side
Bottom side
•Control 6 zones of RF receivers separately.
• CCT color controller
• High sensitive & high stable t, fast & precise color control.
• Compatible with all universal series RF receivers
• 1 receiver can be paired by max 8 different remote controls.
• Waterproof grade: IP20
Product Data
Safety & Warnings
Power Supply 4.5V(3xAAA battery)
Indicator: indicate the
state of remote control
S4 S5 S6
456
23 1
S1 S2 S3
Touch color wheel, touch to select
color temperature
Press and hold down to increase/
decrease light intensity
25% brightness
100% brightness50% brightness
75% brightness
Click to turn ON/OFF all zones
Press and hold down to save colors;
Click to recall the saved colors
Zone numbers:Click to choose the zone/
zones, Press and hold down to turn on/off
corresponding zone
3xAAA battery
•This device contains AAA batteries that shall be stored and disposed properly.
•DO NOT expose the device to moisture.
Pair with RF receiver(Method 1)
Step 4:Choose and click a zone number(e.g. zone 6)
Step 3:Click the “Learning Key” button on RF receiver or re-power on the receiver
three times continuously to set it into pairing status
Learning Key
RF LED Receiver
Step 1:Do wiring the RF receiver according to wiring diagram(please refer to the
instruction of RF receiver that you would like to pair with.
Step 5:Touch the color wheel, LED lights connected with the RF receiver flicker
once means the receiver is paired with zone 6 successfully.
Step 2:Click ON/OFF button to activate the remote
Pair with RF receiver(Method 2)
Step 4:Choose and click a zone number(e.g. zone 3) twice, then press and hold it
continuously and quickly within 10 seconds, LED lights connected with the RF receiver
flicker once means the receiver is paired with zone 3 successfully.
Step 3:Power off and power on the receiver
Learning Key
RF LED Receiver
Step 1:Do wiring the RF receiver according to wiring diagram(please refer to the
instruction of RF receiver that you would like to pair with.
Step 2:Click ON/OFF button to activate the remote
S4 S5 S6
456
23 1
S1 S2 S3
S4 S5 S6
456
23 1
S1 S2 S3
Beulux Code: C92-6ZR

Save color/scene/mode
Step 2:Choose and click one or multiple paired zone numbers(e.g. zone 3)
Step 1:Click ON/OFF button to activate the remote
Step 3:Touch the color wheel or click the other buttons to select the scene you like
Step 4:Press and hold any scene buttons of S1-S6(e.g. S3) , LED lights connected
with the RF receiver flicker once means the color/scene was saved successfully.
Recall the saved colors/scenes
Step 2:Choose and click one or multiple paired zone numbers(e.g. zone 3)
Step 1:Click ON/OFF button to activate the remote
Step 3:Click any scene buttons of S1-S6(e.g. S3) to recall the saved scene
If you use multiple receivers, you have two choices:
Option 1: have all the receivers in the same zone, like zone 1
Lear ning Ke y
RF LED Rec eiv er
Zone 1
Option 2: have each receiver in a different zone, like zone 1, 2, 3 or 4
Zone 1 Zone 2 Zone 3
RF remote
RF remote
Lear ning Ke y
RF LED Rec eiv er
Lear ning Ke y
RF LED Rec eiv er
Lear ning Ke y
RF LED Rec eiv er
Lear ning Ke y
RF LED Rec eiv er
S4 S5 S6
456
23 1
S1 S2 S3
S4 S5 S6
456
23 1
S1 S2 S3