MELICONI SPEEDY 210 STB User manual

5
Thank you for choosing MELICONI.
This simplified universal remote control contains all the main functions of most TV and digital
terrestrial and/or satellite decoder (STB) remote controls.
Before programming and using the remote control, fit the batteries.
Keep your Instructions and Code Booklet for future reference.
USING THE KEYS AND FUNCTIONS
FITTING THE BATTERIES
GB
SET-UP
Read these instructions carefully before programming your remote control!
To command your appliances, you must program your Speedy 210 STB as described in
paragraphs Aor Bbelow.
Visit out Internet site www.meliconi.com for interactive instructions for easy and fast remote
control programming. Warning: programme one appliance at a time.
Before programming and using the remote control, fit the batteries.
The remote control requires 2 new AAA/LR03 alkaline batteries. Insert the batteries as shown.
• The batteries must be changed once a year.
• Change the batteries if the light indicator starts to flash during use.
The batteries are low.
• This remote control has a permanent memory and does not lose the
programmed codes when the batteries are removed.
• Make a note of the code for your TV on the adhesive label supplied
inside the battery cover. This note will be handy if you have to
reprogram your remote control.
ON/OFF key to turn the appliance off,
or in some cases on.
Control the volume using
+ .
To select an external input terminal.
To select the next program or
to turn ON your TV.
Mute key.
Control the volume using - .
Teletext keys:
to access Teletext
close Teletext and return to
normal viewing
Numeric keypad.
Light indicator.
Selection key to control the decoder.
To select the previous program or
to turn ON your TV.
Selection key to control the TV.
istr. SPEEDY 210 SB-17 lin 12-12-2007 15:51 Pagina 5

6
Identify the code and make a note of it following the code noting procedure
(see “PROGRAMMED CODE NOTING” section).
1. Turn on the appliance to be programmed and select a programme.
2. Look for your TV brand in the list of codes at the end of this booklet and make a note of the
corresponding code indicated alongside (e.g. Philips 0025). If your TV brand is not listed, apply the global
search described in paragraph B.
3. Hold the selection key corresponding to the appliance whose code you are looking for ( or ) down
for five seconds until the light indicator at the top starts flashing to indicate that the remote control is
programming.
4. Release the keys, Within 15 seconds, enter the brand code previously identified (e.g. 0025). The light
indicator flashes more quickly to indicate that the remote control is ready for the search.
5. Point the remote control at the appliance. Press and release the key slowly several times and stop
when the appliance goes off (you may have to press the key dozens of times).
6. When the appliance goes off, press the key to confirm.
Three long flashes indicate that the operation has been completed correctly.
Additional check
Check that some of the other functions used on your original remote control are working correctly. If the
commands function incorrectly or erratically, you have probably entered a code for a similar but different
remote control. In this case, repeat the search procedure from point 3.
HOW TO PROGRAMME THE REMOTE CONTROL
A
NOTE: during the search operation, the light indicator flashes more quickly. The light indicator
stops flashing and the remote control leaves the programming mode in the following cases:
• if no keys are pressed for 12 seconds
• if the code search list is completed. In this case, switch to programming mode B
This operation may take a few minutes.
1. Turn on the appliance to be programmed and select a programme.
2. Hold the selection key corresponding to the appliance whose code you are looking for ( or ) down
for five seconds until the light indicator at the top starts flashing to indicate that the remote control is
programming.
3. Release the keys. Within 15 seconds, enter the code 0000.
The light indicator flashes more quickly to indicate that the remote control is ready for the search.
4. Point the remote control at the appliance. Press and release the key slowly several times. Stop when
your appliance goes OFF (you may have to press the key over a hundred times).
5. When the appliance goes off, press the key to confirm. Three long flashes indicate that the
operation has been completed correctly.
Additional check
Check that some of the other functions used on your original remote control are working correctly.
If the commands function incorrectly or erratically, you have probably entered a code for a similar but
different remote control.
In this case, repeat the search procedure from point 2.
GLOBAL SEARCH REMOTE CONTROL PROGRAMMING
B
istr. SPEEDY 210 SB-17 lin 12-12-2007 15:51 Pagina 6

7
Identify the code and make a note of it following the code noting procedure
(see “PROGRAMMED CODE NOTING” section).
NOTE: during the search operation, the light indicator flashes more quickly. The light indicator
stops flashing and the remote control leaves the programming mode in the following cases:
• if no keys are pressed for 12 seconds.
• if the code search list is completed. In this case, visit www.meliconi.com
Always write down the 4-digit codes for your remote control on the label inside the battery cover
after running the search and saving the codes.
This may be useful if you need to reprogram your remote control in the event of accidental
cancellation.
To find the codes for your remote control:
1. Hold the selection key corresponding to the appliance whose code you are looking for ( or ) down
for five seconds until the light indicator at the top starts flashing to indicate that the remote control is
programming.
2. After releasing the keys enter the code number you noted down previously. Three flashes indicate that
the code has been saved correctly. If not, try the code entry procedure again from point 1.
PROGRAMMED CODE NOTING
1. Hold the selection key whose code you are looking for down for five seconds until the light indicator at
the top starts flashing to indicate that the remote control is programming.
2. Release the selection key ( or ) and then press and release the key within eight seconds.
3. After a few seconds, the light indicator communicates the code you are looking for by flashing the four
numbers separately. Count the number of flashes for each code number. For example, for the code 1306,
the key flashes one, three, ten and six times to give:
= 1
= 3
= 0
= 6
4. Note this code on the label inside the battery cover, for rapid consultation.
RE-PROGRAMMING YOUR REMOTE CONTROL BY ENTERING THE CODE NOTED DOWN
TV FUNCTIONS ALWAYS ACTIVE
The MUTE, VOLUME -, VOLUME + keys can also be used to control the decoder. To use these functions on
the digital decoder, press the corresponding key while holding the STB key down at the same time.
istr. SPEEDY 210 SB-17 lin 12-12-2007 15:51 Pagina 7

8
TROUBLESHOOTING
PROBLEM
The appliance does not respond and the light
indicator does not light up when you press a
key.
The appliance does not respond but the light
indicator lights up.
When a key is pressed, the light indicator
flashes and the appliance does not respond
to the commands.
The remote control commands are not all
working correcting.
The code for your appliance brand is not in
the list of codes of the end of this booklet.
SOLUTION
Check that the batteries are fitted correctly. If
necessary, replace them with 2 new 1.5 V
AAA/LR03 alkaline batteries.
Check that the batteries are new and that the
remote control is pointing at the appliance
without any obstacles in the way. If required,
reset the remote control code, following the
programming procedure A or B.
The batteries are low. Change them.
You may have used the wrong code. Reset
the remote control code, following the
programming procedure Aor B .
Set the remote control code, following the
global search programming procedure B.
WARRANTY: 2 years
The warranty ceases to be valid if the product is tampered with or
used incorrectly.
Remote control model Speedy 210 STB
Purchase date
If you have any queries about Speedy 210 STB:
•read this booklet carefully– this will help you to solve almost all problems
•consult our Internet site www.meliconi.com to answer all your queries more easily and quickly.
Agent's stamp
INFO LINE
istr. SPEEDY 210 SB-17 lin 12-12-2007 15:51 Pagina 8