BEYES Maxso X200 User manual

Instructions For Use
X200 High Speed Collection
Table of Contents
• Before You Begin
• Safety Information
• Technical Specifications
• Assembly & Removal
• Friction Grip Bur Specifications
• Bur Insertion & Removal
• Cleaning & Lubrication
• Warranty
WARNING!
(Risk of injury)
ATTENTION!
(To prevent damage)
Thermal washer
disinfectable
General
explanations,
without risk to
persons or objects
Sterilizable
up to the stated
temperature
Technical Specifications
Assembly & Removal
This handpiece should only be used on dental delivery systems that provide filtered
and regulated air and water. Filtration of 25 microns is recommended.
Ez-Swivel PD Coupling (Fig. 1.1)
1. Ensure PD coupling is firmly attached to the handpiece tubing
2. Align PD coupling into handpiece and push together
3. Ensure handpiece is firmly attached to coupling
4. Pull the retention sleeve of the PD coupling back and remove
the turbine handpiece by pulling in an axial direction
Other Approved Manufacturer’s Couplings (Fig. 1.2)
Connection: Refer to original manufacturer's instruction for use. (Do NOT use unapproved couplings)
1. Attach the turbine handpiece to the Kavo®, NSK®, W&H® and Star®
coupling as described by the coupling manufacturer
2. Check that the connection to the coupling is secure.
3. Remove the Kavo®, NSK®, W&H® and Star® coupling as described
by the coupling manufacturer.
Before You Begin
Please read this Manual prior to using your Maxso Highspeed Handpiece. The use of this
product is only intended for use by trained dental personnel. We recommend that you
retain this manual for future reference.
Safety Information
• High speed handpieces should be sterilized after each patient to prevent any
transmission of infective organisms.
• Suitable hygienic measures must be taken to prevent cross contamination between
patients, operators and other personnel.
• Only operate this highspeed handpiece when the bur is properly inserted in the chuck.
Do not attempt to extend the length of the bur by improper positioning in the chuck.
Water & Air Adjustment
Coolant Water: Adjust the water volume at the delivery unit to obtain a satisfactory spray mist.
Air Pressure: The operating pressure Must be 2.62 bar to 2.90 bar, and recommendation
is 2.76 bar. It is highly recommended that the operating pressure initially be set using a
handpiece pressure gauge due to the pressure loss caused by the handpiece tubing
material and length.
Warning: Do not exceed 3.52 bar operating pressure as this will shorten turbine life
and may cause additional damage to the handpiece.
Handpiece Operation
Use standard length concentric diamond and carbide burs with 1.59mm nominal diameter
friction grip shanks designed for high speed handpieces.
Use only burs with hardened tempered steel shanks. Before use, verify concentric
rotation by operating handpiece outside the or alcavity in a safe place.
Warning: Do not use burs that produce excessive noise or do not run concentrically. Do
not use burs that are modified, eccentrically designed, or have bent or ‘soft’ (nonheat
treated) shanks.
Friction Grip Bur Specifications
For application details and operating data of the different rotary instruments please refer
to the information provided by the manufacturer.The push button autochuck turbines
have the following bur requirements:
Use only instruments whose shanks comply with the requirements of ISO 1797-1.
• Shank diameter of 1.59—1.60mm
• Overall length up to max. 25mm
• Overall length up to max. 21mm (mini)
• Working diameter up to max. 2.1mm (ISO 021)
Instruments that differ from the specified data must not be used.
Otherwise the mechanism of the clamping system could be damaged.
Fig. 1.2
KavoR
NSK R
W&HR
Star R
Rotary instruments
Idle mode speed
Coolant supply volume
Water setting range
Chip air setting range
Return air pressure
Operating pressure
Air consumption
Chip air consumption at 2 bar
Standard Head (S)
350,000-360,000
1.6-0.01
>50
0.7-2
1.5-3
<0.5
30-45
>1.5 >1.5
30-45
0.7-2
1.5-3
<0.5
>50
1.6-0.01
380,000-410,000
2.62-2.90 2.62-2.90
Mini Head (M)
EN ISO 1797-1:1995 (0mm)
(rpm)
(ml/min)
(bar)
(bar)
(bar)
(bar)
(NL/min)
(NL/min)
23 21Power/Torque (watt)
Do not assemble/remove during operation!
Fig.2 Bur Specifications
Dia. max. 2.1mm Dia. 1.59 ●1.60mm
Controler/Racer max.25mm
Mini max. 21mm
Maxso®
Fig. 1.1

Handpiece Lubrication (Turbine)
• After internal cleaning
• Prior Sterilization
• After 30 minutes of use or at least once daily
Purging
Connect handpiece to tubing and run handpiece for 20-30 seconds to purge remaining
lubricant.
Automatic Handpiece Lubrication
After cleaning the handpiece simply connect the handpiece to the correct adaptor and
activate the Lubrication System according to the manufacturer’s system instructions.
Manual Lubrication (Fig.7)
After cleaning the handpiece apply lubricant
BEFORE sterilization
1. Use only a high quality lubricant such as Beyes Lube.
2. Ensure the correct application nozzle is connected to
the plastic valve at the top of the spray can.
3. Firmly insert the application nozzle into the rear
of the handpiece
4. Spray for 2-3 seconds
5. Wipe any excess lubricant from the handpiece.
Sterilization
Following your country specific directives, standard and guidelines
• Steam sterilization class B (pre and post vaccum) with sterilizers in accordance with
EN 13060.
OR
• Steam sterilization class S with sterilizers in accordance with EN 13060
The sterilizer manufacturer must give the express approval for the sterilzation of turbine
handpieces.
An unwrapped handpiece needs to be used immediately or sterility is not maintained.
Do not exceed the sterilizer manufacturer’s guidelines for load capacity.
Use steam sterilization exclusively for complete sterility. Never dry heat sterilize,
ultrasonically clean, or expose handpiece or swivel to chemical disinfection or cold
sterilization.
Limited Warranty
Beyes Dental Canada hereby warrants against defect in material and workmanship that
for a period of 12 months (six months for turbine) from the date of purchase, this product
will perform satisfactorily under normal use and service. No warranty claim can be inferred
here, as wear may occur earlier or later than indicated above depending on use,
frequency of sterilization and frequency of maintenance. Beyes shall under no
circumstances be liable for incidental or consequential damages or damage due to
improper use or maintenance.
This Warranty is subject to the following conditions
Beyes will, without charge repair or replace (at Beyes sole discretion) any defective part/s
covered in this warranty.If the conditions are met, the defective item must be returned to
an authorized Beyes service center or distributor. Accompanied by the original invoice or
packing list. This warranty is in lieu of all other warranties, expressed or implied .
* This device is not field repairable
* All brands are holders of their respective trademarks.
Fig.4
Federal law restricts this device to sale by or on the order of a dentist, physician, or any other practitioner licensed by
the law of the states in which he or she practices to use or order the use of this device.
I123EN.REV0Z1721
Bur Insertion (Fig.3)
1. Insert bur into autochuck until resistance is felt.
2. Depress the autochuck end cap button and continue to feed-in
the bur until it clicks and stops.
3. Release the autochuck end cap button. (Always pull on the bur
after it has been installed to confirm that it is seated properly).
4. Never depress the autochuck end cap when the bur is rotating.
Use only faultless burs and diamonds.
These must be clean to prevent dirt from being transferred into
the chuck.
Fig.3
Bur Removal (Fig.4)
1. Grasp handpiece firmly so your thumb touches the end
cap of the autochuck and push until a slight ‘click’ is noticed.
2. Pull bur straight out.
3. Release end cap.
Never depress the autochuck end cap button or rest the
end cap against any part of the oral cavity during operation.
Depressing the end cap while a bur is rotating can activate
the chuck mechanism and result in the end cap button with
excessive heat and / or loss of bur retention.
Chuck System Lubrication (Fig.6)
1. Fit the spray nozzle onto the spray can
2. Grip the handpiece firmly
3. Press the tip of the spray nozzle firmly
into the chuck system
4. Spray about 1 second
5. Push the button three times
Fig.7
Fig.6
Fig.5.2
Fig.5.1
Lubrication
Beyes Dental Canada Inc.
30 Casebridge Court
Toronto, Ontario, M1B 3M5
Canada
Tel: [phone]
Email: [email protected]
Beyes Europe MEDevice Union ltd.
26 York Street
London, W1U 6PZ
United Kingdom
Tel: [phone]
Email: [email protected]
External Cleaning
Fiber Optic Rod
Clean the Fiber Optic Rod using isopropyl alcohol or other disinfection agents. Super soft
cleaning cloth must be used. Never use a cleaning agent that has an ammonium,
chlorine, or acid base. (Fig.5.1)
External Surface
Clean debris from the external surface by using isopropyl alcohol
or other disinfecting agents. Never use a cleaning agent that has
an ammonium, chlorine, or acid base. Dry thoroughly.
Never immerse the handpiece in disinfection baths.
Improper care and maintenance may lead to a premature
wear and failure of the handpiece. (Fig.5.2)