BEYES Maxso E600 User manual

Electric Micromotor System
Instruction for Use
Maxso®E600

2
Operation Manual
•EquipmentClassication
- Class II equipment:
- Type B shock protection:
- Recommended sterilization: See 7. Sterilization
-Donotuseinthepresenceofammableliquidsorgases.
Cautions for safe handling and operation
Readthesesafetyprecautionsrstbeforeusingthisproduct.
These instructions will show you how to operate this product safely and prevent injury to yourself
orothers.Theyareclassiedbythedegreeand/orseverityofdanger.Allcautionsregardingsafety
shouldbeobserved.
Classication Degree and severity of danger
Warning Provides an instruction where personal injury may occur.
Caution Provides an instruction where minor to medium injury may occur.
Notice Providesaninstructionthatshouldbeobservedforsafetyreasons.
Warning
-ToPreventElectricShock:Donotpluginthepowercordwithwethands.
-ToPreventElectricShock:Preventwaterfromgettingontothecontrolbox.
-ToPreventElectricShock:Pluginandremovethepowerbyholdingontothebaseoftheplugand
not the cord.
-ToPreventElectricShock:Useanelectricaloutletwhichisgrounded.
-Ifyoufeelanyabnormalitysuchasexcessivevibration,heat,ornoise,stopusingtheunit
immediately.
Caution
-Whenoperatingthissystem,alwaysconsiderthesafetyofthepatient.
-Theproductisdesignedforclinicaldentalusebyqualiedpersonnel
-Everyconnectionmustberm.Ifitisnotrmlyconnected,itmaycauseanairorwaterleak,orthe
LEDmightnotturnon.
-Donotdroptheproductorcauseittobeimpactedinanyway.Thiscouldcauseamalfunctionand
damage.
-ThissystemistobeusedwithISO9168,typeBortypeChoseconnector.
-Thissystemismeanttofunctionintemperaturesof0-40°C(32-104°F),humidityat10-85%RH,
atmosphericpressure700-1060hPaandnomoistureorcondensationintheControlUnit.Operating
outside of these parameters can cause a malfunction.
-WheninstallingtheControlBoxorMotor,donotbendortwistthetubingorthecord.Noexcessive
force is need to do the installation.
-Donotusecontaminatedair(bydustormoisture).Iftheaircontainswaterordust,itmightcause
amalfunctionoroverheating.

3
Caution
Unit
-Graspcordbytheplugtoremovefromtheoutlet.Donotpulloryankthecorditself.Itmaycause
the wire to malfunction.
-CareshouldbetakennottoplacetheACcordnearagasburner.Neverattempttorepairaburned
motorcord.Alwaysreplaceitwithanewcord.
-Priortouse,alwayscheckforvibration,noiseandoverheating.Ifanyabnormalitiesaredetected,
stopusingimmediatelyandcontactyourdealer.
-Becarefulnottospillwaterontotheunitasitmayresultinareoranelectricshockduetoashort
circuit.
Motor, Hand piece
-Donotusethisproductunderstrongstressforextendedperiodsoftime.Itcancauseoverheating.
- Do not connect or disconnect the cord until the drive motor has completely stopped.
-Donotconnect/disconnectthehandpieceduringoperation.
-VerifythattheSpeedControlSwitchisadjustedwithintheallowablespeedbeforeuse.
-Connectonly4-hole,5-holeor6-pintubing.
-AirRequirements:Dry,freefromcontaminationandoil.Useacompressorwithadryairsystem/
Installanairlterifnecessary/Blowoutthelinesbeforeinstallation.
-Donotautoclave(oranyotherhightemperaturesterilization)ControlBox,ACAdaptor,MotorCode.
-Theusershallberesponsibleforoperationandmaintenanceandinspection.
Notice
Duringrotation,themotorandmotorcordmayaffectcomputerandLANcables.Noisecouldbeheard
duringoperationnearradioreceivers.
Aftertreatment,immediatelyturnthepowerandairsupplyoff.Removethepowercordiftheunitis
nottobeusedforalongtime.
1. Specications
Model Maxso E600P
Speed 2,000~40,000rpm
Torque 3.4Ncm
Rated Input AC24V/DC36
NoiseLevel <60dB
Dimensions W127xD149xH54(mm)

4
2. Component Names
1. ControlBox  
2. DigitalSpeedDisplay 
3. Gear Ratio Lamp
4. Gear Ration Select Key
5. FWD/REVSelectKey 
6. Program1Button  
7. Program2Button
8. SpeedAdjusters  
1
9
10
2
3
4
6
5
7
8
12
11 13 14
16
15
9. Motor
10. MotorCord
11. PowerSwitch
12. ACAdapterConnector
13. MotorCordConnector
14. TurbineHoseConnector
15. ACCord
16. ACAdaptor

5
3. Control Box Operation
Caution
Makesurethereisnoresidualairorwaterintheturbinehosewhenconnectingittothecontrolbox.
Handtightenthenutproperlywithoutexcessiveforcewhenconnectingtheturbinehoseandthe
motor cord connector.
3-1 Connect the hand piece tubing from your delivery unit.
Fittheturbinehoseplugfromthedeliveryunittotheturbine
hoseconnectorandtightencompletely.
Caution
- Do not use any other hose than the ones provided with the unit
- Do not use contaminated air
-Blowoutthelinesbeforeinstallation
Caution
NeveruseanyACadapterotherthantheoneprovidedwiththis
product.
3-4 Connecting the Power Cord
InsertthepowercordintotheinletoftheACadapter.
3-2 Connecting the Motor.
Connectthemotorbyaligningthemotorcordplugandinsert
rmly.
3-3 Connecting the AC adapter
InserttheACadapterplugintotheACadapterconnector
beforepluggingitintothewalloutlet.

6
4. Handling the Motor
4-1 Connecting/Disconnecting the motor and motor cord.
Alignandinsertthemotorpinrmlyintothepinholesofthe
motor cord connector and fasten the motor cord nut securely.
Toremovethemotorcordfromthemotor,unscrewand
detachthemotorcordnut,andgentlypulloutthemotorcord
connector.
4-2 Connecting/ Disconnecting the motor and hand piece
ToinserttheE-Typehandpieceintothemotor,alignthehand
pieceandmotor,thenturnuntilyouhearaclick(positioning
pinsarealigned)
Toremovethehandpiece,simplypullthehandpiecefromthe
motor.
Caution
-Careshouldbetakenwhenusinganyhandpieceattachmentwhichrequireslubrication(E-Type
micromotor).
-Followinglubrication,standthehandpieceattachmentverticallyuntiltheexcesssolutiondrains.
Wipe the hand piece then attach it to the motor.
- Do not connect or disconnect the handpiece until the motor has completely stopped.
5. Operation
5-1InsertthepowercordplugintotheACoutletandturnthe
powerswitchon.Whenthepowerswitchison,thelampsand
indicator will come on.
5-2Beforeusingthissystem,makesuretooperatetheFootAir
Calibrationfunction.
5-3PushtheGearRatioSelectKeytoindicatethespeedofthe
attachment you will use.
*CheckTableBelowforSpeeds
HandPieceGearRatio Indicator Speed (min-1(rpm))
16:1 1-25 100–2,500
1:1 2–40 2,000–40,000
1:5 1–20 10,000–200,000
Motor
Motor Cord
Connector
Motor Cord
Nut
Motor Cord
Handpiece(Option)
Positioning
Gear Ratio Lamp
Motor Insert
Push

7
5-4SetthemaximumspeedusingtheRotationAdjustment
Key(+/-).
5-5SelectFWD/REVrotationusingtheFWD/REVSelectkey.
5-6Themicromotoroperationiscontrolledbytheairswitch/
foot pedal of the delivery unit.
Notice
Thedisplayedairpressureisonlyaguideline.Measurethecorrectairpressurewiththeairgauge.
Theunitofdisplayedpressureis“kgf/cP2”
6. Convenient Functions
6-1 Foot Air Calibration
(unitofDisplay=kgf/cP2)
Byusingthisfunction,itenablesyoutousethemaximumspeed,40,000min^(-1)(rpm),eventhough
theairpressureofthedeliverysystemisnothighenough,bysettingtheupperandlowerlimitofthe
air pressure.
Notice
Dothisadjustmentoninitialsetupoftheunit.Onceitisadjusted,itwillbememorizedandyouwon’t
needtoadjustagain.
1)PresstheP2keyandRotationSpeedAdjustmentKey(+)atthesametimeformorethan3seconds.
2)Afterthealarmsound,theindicatorwillchangeto“C1”(Lowerairpressurelimitsettingmode)
3)BypressingtheFWD/REVRotationkey,theSpeedindicatorwillshow“0.0”and“Eb”
4)PressingontheFootPedalofthedeliveryunitwillindicatethecurrentairpressure.
5)Maintainairpressurebetween“0.3”–“1.0”.PresstheP2Keyformorethan3secondsto
memorize the lower limit of the air pressure.
Push
DigitalSpeedDisplay
Increase
Decrease
FWD/REVLamp

8
Notice
-Thedefaultvalueissetto“0.5”
-Whentheairpressureisnotbetween“0.3”–“1.0”.“Ebwillbeshownonthedisplayandthevalue
willnotbememorized.
6)Aftersettingthelowerlimit,presstheGearRationSelectKey.Theindicatorwillchangeto“C2”
(Upperairpressurelimitsetting).
7)BypressingtheFWD/REVrotationkey,theindicatorwillshow“0.0”and“Ec”.
8)Bysteppingonthefootpedalofthedeliverysystem.Theindicatorwillshowthecurrentairpres-
sure.
Notice
Thedisplayedairpressureisonlyaguideline.Measurethecorrectairpressurewiththeairmeter.
9)Maintainairpressurebetween“2.0”–“4.0”.PresstheP2keyuntilitbeeps(morethan3seconds)
to memorize the upper limit of the air pressure.
Notice
The Default value is set to “3.0”.
Whentheairpressureisnotbetween“2.0”–“4.0”thedisplaywillshow“Ec”,andthevaluewillnotbe
memorized.
10)PressboththeP2keyandtheSpeedAdjustmentKey(+)atthesametimeuntilyouhearabeep
(morethan3seconds).Whenyouhearthebeepthesettingiscomplete.
6-2 Light Brightness Adjustment
(unit of Display = V)
BrightnessoftheFiberOpticcanbeadjustedwiththisfunction.
1)PresstheP2KeyandSpeedAdjustmentKey(+)atthesametimeuntilitsbeeps.(morethan3
seconds).
2)Afterthebeep,theindicatorwillchangeto“C1”.PressingtheGearRationSelectKeywillchange
theindicatorandtheGearRationLamp(C1->C2->C3->C1…)SettheindicatorinC3
(LightBrightnessAdjustmentMode).PressFWD/REVRotationKeytoproceed.
3)WhenTheindicatoritsdefaultvalue(“3.5”),PresstheSpeedAdjustmentKey(+/-)toadjustthe
brightness.

9
Notice
DefaultValueissetto“3.5”
Adjustablebetween“1.6”–“3.6”.
4)PresstheP2keyuntilitbeeps(morethan3seconds)tothesetthebrightness.
5)PrestheP2KeyandtheSpeedAdjustmentKey(+)atthesametimeformorethan3secondsto
leavethebrightnesssetting.
6-3 Program Function
Youcanstoreyoursettingsintomemory(Speed,GearRatio,Direction)andthenusetheP1,P2keys
touseyourpreferredsettings.
1)SetthevaluesforSpeed,GearRatio,Forward/ReverseDirection.
2)PresstheP1orP2keyuntilyouhearabeep(morethan3seconds).Whenyouhearthebeep,the
settingiscomplete.
7. Sterilization
Sterilize the motor only.
Forsterilization,werecommendtheautoclavesterilization
method.
Sterilizationisrequiredthersttimeyouusetheunitaswell
asaftereachpatientasnotedbelow.
Autoclaving
1)Turnoffthepower.
2)Detachthemotorfromthemotorcord.
3)Cleanthesurfaceofthemotorwithabrush(Donotusea
metalbrush),andwipeitwithcottonanddisinfectantalcohol.
4)ScrewtheMotorCaptotheMotor.PuttheAutoclavePlug
onto the motor insert.
5)Insertintoautoclaveouch.Sealthepouch.
6)Autoclavableuptoamaximumof135°C.
7)KeeptheMotorintheautoclavablepouchuntilyouare
ready to use it to keep it clean.
Caution
-Donotautoclave(oranyotherhightemperaturesterilization)ControlBox,ACAdaptor,orMotor
Cord.
-Donotlubricatethemotor.
- Do not wipe or immerse the system in acidic water or acidic solutions.
-Donotsterilizewithdirtonthesurface,itmaycauserust.
AutoclavePlug
Motor Cap
Tighten

10
9. Error Codes
Error Code Issue Cause Solution
E0 Overcurrenterror
(InCircuit)
Detected an overcurrent in the
circuit
Contact your dealer
E1 Overcurrenterror.
(InSoftware)
Detected an overcurrent in the
software
Contact your dealer
E2 Retry Error Motor was overloaded and
stopped and can not restart.
Contact your dealer
E3 ITRIP Error Faultymotororinternalcircuit Contact your Dealer
E5 OvervoltageInput
Error
Overvoltagetothecontrolbox Contact your dealer
E6 LEDvoltageerror Overvoltageintheinternalcir-
cuit.(morethan3.7V)
Contact your dealer
E8 Overheatingerror Hightemperaturesafetysystem
activated due to extended use .
Wait for a while and
letitcooldownbefore
usingagain.
8. Maintenance
IftheO-Ringsbecomeworn,themotormightnotconnect
welltothehandpiece,orwatermayleak.Replacethe
O-Rings.
Changing the O-Ring
RemovetheO-Ringatthemotorinsertwithapointedtool,
andmountthenewO-ringsintothegroove.
Caution
Thereare4O-RingsontheMotorInsert.Theblueoneisthinnerthantheother3.Makesureto
install them in the proper spot.
Caution
IftheO-Ringsbecomeworn,itmaycause:
-Air/Waterleak
-Difcultyattaching/disconnectingthehandpiece
-ExcessVibration

11
10. Troubleshooting
Whenhavinganissuewiththeunit,checkthisguidebeforecontactingyourdealer.Thesearethe
most common issues which may occur.
Issue Cause Solution
Pilot Lamp does not come on Power switch is off
-ACAdaptorisnotconnected
properly
-Internalfuseisblown
Turn on the switch
-Check the connection
-Contact your dealer
Motordoesn’tnotrun Tubing,MotorCord,ACadapt-
er is not connected properly
-Airpressureisnotsufcient
Check the connection
-Check the air pressure from
the delivery unit
-refertoErrorcode9
The rotation speed is too slow -Airpressurefromdeliveryunit
is too low
-Airpressureonthedelivery
unit is lower than the “Lower
limit of air pressure”.
Check the air pressure on the
delivery system.
-Do“Foot/Aircalibration
Beepswhenturningonthe
switch
Youaresteppingonthefoot
pedalwhenturningonthe
power switch
Do not step on the foot pedal
whileturningontheswitch
E9 Motor start error Motordidn’treachthepreset
speedintheprescribedamount
of time.
Break down of the motor cord
wire,orinternalcircuitmalfunc-
tion
Contact your dealer
EA LEDvoltageerror VoltagefortheLEDisn’thigh
enough
Contact your dealer
Eb Airoffseterror Lower than preset ‘Lower limit of
air pressure”
Displayedbyfoot/air
calibrationfunction.
NotaMalfunction
Ec Airfullscaleerror Higherthanpreset“Upperlimitof
air pressure”
Airpressurehigherthan0.4MPa
Displayedbyfoot/air
calibrationfunction.
Notamalfunction
EE EEPROMError Malfunctionofthesettings
memory
Contact your dealer

12
11.1 Scope of Warranty
BEYESDentalCanadaInc.(‘BEYES’)warrantstotheoriginalretailpurchaserthatitwillbeatBEYES
optiontorepairorreplacecomponentsofthedentalproductsmanufacturedbyBEYES(exceptfor
componentsnotwarrantedunder‘Exclusions’)thataredefectiveinmaterialorworkmanshipunder
normaluseandservice.BEYES’obligationunderthislimitedwarrantyislimitedtotherepairor
replacementoftheapplicablecomponents.Thislimitedwarrantyshallonlyapplytodefectsthatare
reportedtoBEYESwithintheapplicablewarrantyperiodandwhich,uponexaminationbyBeyes,
provetobedefective.Thiswarrantyextendsonlytotherstretailpurchaserofaproductandisnot
transferableorassignable.Replacementcomponentsorproductsmaybeusedand/orrefurbished
componentsorproducts,providedtheyareoflikequalityandspecicationsasnewcomponentsor
products.
11.2 Applicable Warranty Period
Theapplicablewarrantyperiod,measuredfromthedateofinvoicetotheoriginaluser,shallbe
warrantedforaperiodof25months.
11.3 Exclusions
ThislimitedwarrantydoesnotcoverandBEYESshallnotbeliableforthefollowing;
1)Defects,damageorotherconditionscaused,inwholeorinpart,bymisuse,abuse,negligence,
alteration,accident,freightdamage,negligentstorage,tamperingorfailuretoseekandobtainrepair
orreplacementinatimelymanner;
2)Productswhicharenotinstalled,used,andproperlycleanedandmaintainedasrequiredor
recommendedintheBEYES‘Installation’and/or‘Installation/User’sManual’fortheapplicable
product,includingthespeciedstructuralandoperationalenvironmentconditionsandelectrical
powerrequirements;
3)Productsconsideredtobeofaconsumableorsterilenature;
4)AccessoriesorpartsnotmanufacturedbyBEYES;
5)Chargesbyanyoneforadjustments,repairs,replacementparts,installationorotherwork
performeduponorinconnectionwithsuchproductswhicharenotexpresslyauthorizedinwritingin
advancebyBEYES;
LEDdoesnotlightup Reached the end of life expec-
tancy
Contact your dealer
Motorheatsupabnormally
duringrotation
Coolantairisnotcomingoutof
the delivery unit
Check the air pressure of the
delivery system
WaterLeakage Turbine,Motorcordisnot
connected correctly
Check the connection
Whenturnedon,thesetting
values are different from what
they were set to.
Turned off the motor while it
wasrotating
Do not turn off the unit until
afterthemotorstopsspinning
11. Beyes Limited Warranty Statement

6)Costsandexpensesofroutinemaintenanceandcleaning;
7)RepresentationsandwarrantiesmadebyanypersonorentityotherthanBEYES;
8)Matchingofcolor,grainortextureexcepttocommerciallyacceptablestandards;
9)Changesincolorcausedbynaturalorarticiallight;
10)Custommanufacturedproducts;
11)AlterationsormodicationstotheproductbyanypersonorentityotherthanBEYES;
12)ProductsthatwouldotherwisebecoveredunderSections1and2ofthislimitedwarranty,butare
acquired:(i)fromapersonorentitythatisnotBEYESoroneofitsauthorizeddealers;or(ii)froma
BEYESdealerthatisnotauthorizedtoselltheproductatissueinthegeographicterritorywherethe
purchaserislocated,orisnotauthorizedtoselltheproductatissuewithinthemedical,animalhealth
ordentalmarket,asthecasemaybe,inwhichpurchaserintendstousetheproduct.
11.4 Exclusive Remedy; Consequential Damages Disclaimer
BEYES’OBLIGATIONUNDERTHISLIMITEDWARRANTYISTHEREPAIRORREPLACEMENT
OFDEFECTIVEPARTS.BEYESSHALLNOTBELIABLEFORANDHEREBYDISCLAIMSANY
DIRECT,SPECIAL,INDIRECT,INCIDENTAL,EXEMPLARYORCONSEQUENTIALDAMAGESOR
DELAYS,INCLUDING,BUTNOTLIMITEDTO,DAMAGESFORLOSSOFPROFITSORINCOME,
LOSSOFUSE,DOWNTIME,COVERANDEMPLOYEEORINDEPENDENTCONTRACTOR
WAGES,PAYMENTSANDBENEFITS.
11.5 Warranty Disclaimer
THISLIMITEDWARRANTYISBEYES'ONLYWARRANTYANDISINLIEUOFALLOTHER
WARRANTIES,EXPRESSORIMPLIED.BEYESMAKESNOIMPLIEDWARRANTIESOFANY
KINDINCLUDINGANYIMPLIEDWARRANTIESOFMERCHANTABILITYORFITNESSFORA
PARTICULARPURPOSE.THISWARRANTYISLIMITEDTOTHEREPAIRORREPLACEMENTOF
DEFECTIVEPARTS.

Beyes Dental Canada Inc.
23-595MiddleeldRoad
Toronto,Ontario,P1V3S2
Canada
Tel:1-855-603-1888
Fax: [phone]
Email: [email protected]
Web:www.beyes.ca
Lotus NL B.V.
KoninginJulianaplein10,IeVerd,
2595AA,TheHague,
Netherlands
Tel:[phone](English)
 [phone](Dutch) 0197
Printed in Canada
File#:ENI019R1
Federallawrestrictsthisdevicetosalebyorontheorderofadentist,physician,oranyotherpractitionerlicensedby
the law of the states in which he or she practices to use or order the use of this device. Beyes Dental Canada Inc. is not
responsibleforanytypographicalerrors.Subjectstotechnicalchangeswithoutnotice.*Allbrandsareholdersoftheir
respective trademarks.