BH FITNESS G5 HA900FT User manual

HA900FT
Fitting G5

2

3

4
Assembly Drawing

5
Assembly
Step one
Attach the front (16) and rear feet (12) to the frame using the nuts (8), washer (9) and bolts (10).
Step two
Attach the handlebar post (37) inserting into the head tube on the frame. Using knob to adjusts
and tightens the height in proper position. Then attached handlebar slider (21) on the handlebar
post (37), use knob (4) to adjust and tighten the handlebar in proper position.
Step three
Insert the seat post (41) into the frame’s seat tube. Attach the saddle (1) into seat slider (40).
Insert the seat slider into the seat post and fix. Using knob (4) adjusts and tightens the height in
proper position.
Step four
Attach the pedals (11) into the crank arms (5)(7), each pedal is marked with the L (left) or R
(right) to denote the side of the spinning bike they are on, Note- the right hand crank is on the
same side as the belt guard (6). Be careful to align the threads correctly to avoid any damage.
A little grease on the threads should help the pedals to screw in easily and correctly, tighten using
a 15mm spanner; both pedals threads should tighten towards the front of the spinning bike.
Adjusting the resistance
To adjust the exercising resistance on the complete spinning bike by the brake knob (31) of brake
system, and then simply loosen (-) or tighten (+).
The flywheel should rotate freely without resistance when you loosen (-) the brake system
totally.
More experienced riders may wish to increase the overall resistance by tighten (+) the brake
system totally.

6
Exploded Drawing

7
Part list
No. Name Unit No. Name Unit
1 Saddle PC 31 Brake system SET
2 Alloy bind clip ( R) & ( L ) PC 32 Bolt for front chain guard PC
3 Knob spring PC 33 Front belt guard PC
4 Knob w/washer PC 34 Bottle PC
5,7 Crank arm set SET 35 Bolt & washer for spring plate PC
6 Outer belt guard PC 36 Belt PC
8 Foot tube nut PC 37 Handlebar post PC
9 Foot tube washer PC 38 Rubber sleeves PC
10 Foot tube bolt PC 39 End plug PC
11 Pedal PR 40 Seat slider PC
12 Rear foot tube (complete) SET 41 Seat post PC
13 Foot tube adjuster pad PC 42 Bolt for outer chain guard PC
14 Foot tube end cap PC 43 Flywheel SET
15 Moving wheel PC 44 Flywheel adjuster bolt PC
15-1 Axle bolt for moving wheel PC 45 Bolt for inner belt guard M6 PC
16 Front foot tube (complete) SET 45-1 Washer for inner chain guard PC
17 Leather pad PC 46 Bolt for sensor support PC
17-1 Screw for leather pad PC 47 Cable clip PC
18 Leather pad holder PC 48 Bolt for cable clip PC
19 Screw & nut PC 49 Knob fixed bolt PC
20 Spring plate PC 50 Knob plastic washer PC
21 Handlebar PC 51 Knob washer PC
22 Crank bolt PC 52 Belt pulley with screw PC
23 BB bearing PC 53 Flywheel security washer PC
24 BB Axle w/plate PC 54 Left axle cover PC
25 Flywheel nut cap PC 55 Flywheel axle housing (L) PC
26 Flywheel axle PC 56 Flywheel axle housing(R ) PC
27 Flywheel bearing PC 57 Middle seat post PC
28 Computer - NEW PC 58 Rubber sleeve for seat post PC

8
29 Bottle cage PC 90 Sensor and cable PC
30 Screw for bottle cage PC
Instruction Use
1) The model HA900FT is designed to be used as a “spin “ cycle in fitness studios and health clubs. It has a fixed
wheel driven flywheel and should only be used under professional supervision.
2) Installation – it is important that the HA900FT is correctly assembled and we recommend that suitably qualified
personnel carry out installation and assembly
.
3) Handlebar and seat adjustment. It is important that the handlebar and seat are set at the correct height for your
body. Ask your instructor for assistance. Adjusting the handlebar height-Undo knob that is located where the
handlebar post fits into the frame. Slide the handlebar post up or down to the required height and retighten the
knob. Make sure it is securely tightened and that there is no lateral or vertical movement of the handlebar. The
handlebar position can also be adjusted forwards or backwards. Undo the Release lever located below the
handlebar slider. Slide the handlebar assembly forwards and backwards until you reach the required position.
Then securely re-tighten the Release lever.
Adjusting the seat height- undo the knob located where the seat post fits into the frame. Adjust the seat to the
required height. Then retighten the knob. Make sure it is tighten enough to prevent the seat from twisting side
to side. The seat position can be adjusted forwards and backwards. Undo the knob located directly side of the
seat slider. Loosen the knob then slide the seat to the required position. Then make sure the knob retighten.
4) Pedals and toe straps- your feet should be securely positioned in the toe clips during the exercise. Put your foot
as far forwards as you can into the toe-clip and then pull the strap tight.
5) The HA900FT should operate on a level surface with no lateral movement. There is height adjuster pad located
on either side underneath of the foot tube. Turn these pads clockwise or anti-clockwise until the bike is totally
stable on the ground.
6) Emergency brake – Press down brake system (31) for stop.
7) Maintenance – It may be unsafe when loosen bolt on the parts or noise on the flywheel, please contact your
supplier. Like any other mechanical cycling device, the HA900FT should be regularly maintained. Ask your
supplier for a detailed maintenance program.

9
Maintenance Chart
No DESCRIPTION Daily Weekly Monthly Quarterly Annually
1
Keep machine clean: Wipe machine
down with clean & dry fabric to clear
dirt & sweat.
X
2
Spray with WD40 or similar on the
seat post set, handlebar set (Don’t
spray on the main frame)
X
3 Visual check X
4 Check security of handle bar post &
seat post X
5 Check security of saddle X
6 Remove handlebar post and clean
tube X
7 Remove seat and clean tube X
8 Check brake pads for wear-align X
9 Check brake adjustment X
10 Check security of all knobs & release
lever X
11 Check toe straps for signs of wear X
12 Check crank bolts and re-tighten X
13 Make sure pedals are screwed in X
14 Check belt tension X
15 Wipe the anti-rust oil on the
flywheel X
16 Check bottom bracket X
17 Check flywheel bearings X
18 Full service-frame inspection X

10
LimitedWarranty
This product carries the following guarantee against manufacturing defects:
* Frame is warranted for 2 years from the date of purchase.
* Components are warranted for 1 year.
* Warranty is only valid for the original purchaser.
* Labor and freight charges are not included.
* Normal wear, neglect, abuse, accidents, improper assembly or maintenance, or the
installation of parts or accessories not compatible with the original intended use
of the bike, as sold, are not covered by the warranty.
* Neither does it cover any corrosion caused by failure to clean the bikes on regular
basis.
* This warranty is limited to the repair or replacement of the defective part at no
cost. The supplier shall in no event be responsible for consequential, special
damages, and any parts failures, breakages or injuries resulting from misuse of
the machine or failure to follow the recommended maintenance procedures.
* Warranty claims must be through an authorized dealer, and replacement parts will
normally be dispatched to you. We recommend you held a small stock of basis
spare parts, as well as a tool kit to cover the regular maintenance routines.
* The Limited Warranty is the only express or implied warranty
applicable to original supplier. Any implied warranties, including warranties of
merchantability and fitness shall be limited in scope and duration in accordance
with this limited warranty.

11

12
HA900FT
Fitting G5