BH FITNESS H915P User manual

OWNER’S MANUAL
EXERCISE BIKE
H915P

2

3

4
Assembly Drawing
STEP 1
Attach the front (16) and rear feet
(12) to the frame using the nuts (8),
washer (9) and bolts (10).

5
STEP 2
STEP 3
Attach the handlebar post (23) inserting
into the head tube on the frame.
Using knob (4) to adjusts and tightens
the height in proper position. Then
attached handlebar slider (21) on the
handlebar post (23), use release lever
(22) to adjust and tighten the handlebar
in proper position.
Attach the saddle (1) into seat slider
(41). Attach the pedals (11) into the
crank arms (5,7), each pedal is marked
with the L (left) or R (right) to denote
the side of the spinning bike they are
on, Note- the right hand crank is on the
same side as the belt guard (24). Be
careful to align the threads correctly to
avoid any damage. A little grease on
the threads should help the pedals to
screw in easily and correctly, tighten
using a 15mm spanner; both pedals
threads should tighten towards the
front of the spinning bike.
Attach the bottle cage (29) to the
frame using screw(30) & washer (43).
Console (15) already inserted on
bracket. Attach the Console’s bracket
on the handlebar (21), then tighten the
screw of bracket. Connect the cable
from frame with console.

6
STEP 4
Adjust the exercise resistance on the spinning bike using the tension knob (31) to
loosen (-) or tighten (+).
Emergency brake –Press down brake system (31) for stop.
MOVING
There are moving wheel (13) located
in front foot tube end cap for easy to
moving the machine.

7
Instruction ;
Exploded Drawing
Handlebar and seat adjustment. It is important that the
handlebar and seat are set at the correct height for
your body. Ask your instructor for assistance.
Adjusting the handlebar height-Undo the knob that is
located where the handlebar post fits into the frame.
Slide the handlebar post up or down to the required
height and retighten the knob. Make sure it is securely
tightened and that there is no lateral or vertical movement
of the handlebar. The handlebar position can also be
adjusted forwards or backwards. Undo the adjuster lever
located below the handlebar slider. Slide the handlebar
assembly forwards and backwards until you reach the
required position. Then securely re-tighten the adjuster
lever.
Pay attention on ” MIN INSERT” mark for safety
adjustment.
Adjusting the seat height- undo the knob
located where the seat post fits into the frame.
Adjust the seat to the required height. Then
retighten the knob. The seat position can be
adjusted forwards and backwards. Undo the
knob located directly side of the seat slider.
Loosen the knob then slide the seat to the required
position. Then make sure the knob retighten.
Pay attention on ” MIN INSERT” mark for safety
adjustment.
Seat :
Make sure tighten enough for both side of
nut after adjust the seat position. To
prevent the seat from twisting side to side.

8

9
Part list
No.
Name
Unit
No.
Name
Unit
1
Saddle
PC
34
Outer chain guard bolt (M6)
PC
2
Alloy clip R & L
PR
35
Bolt and washer for spring plate
PC
3
Knob spring
PC
36
Flywheel adjuster bolt
PC
4,37
Knob w/washer
PC
38
Knob plastic washer
PC
5,7
Crank arm set w/magnet
SET
39
Knob fixed bolt
PC
6
Chain
PC
40
Knob washer
PC
8
Foot tube nut
PC
41,55
Seat slider w/ end cap
PC
9
Foot tube washer
PC
42
Seat post
PC
10
Foot fixing bolt
PC
43
Washer for bottle cage
PC
11
Pedal
PR
44
Flywheel
SET
12
Rear foot tube
SET
45
Outer chain guard bolt (M5)
PC
13
Front foot end cap
PR
46
Rubber sleeves
PC
14
Rear foot end cap w/adjuster
wheel
PR
47
Bolt for bracket
PC
15
Console
SET
48
Fender fixed bracket
PC
16
Front foot tube
SET
49
Fender
PC
17
Brake pad w/holder
SET
50
Stainless screw for fender
PC
18
Cable clip
PC
51
Stainless nut for fender
PC
19
Screw & nut for brake pad
PC
52
Stainless washer for fender
PC
20
Spring plate
PC
53
Cover for flywheel w/bolt
SET
21
Handlebar w/slider
PC
54
Bolt for cable clip
PC
22
Release lever w/washer
PC
56
End plug
PC
23
Handle bar post
PC
57
Cable plug
PC
24
Outer chain guard
PC
58
Bolt for sensor support
PC
25
Flywheel axle
SET
26
Fixed wheel sprocket
27
Flywheel bearing
33
Flywheel security nut cap
28
BB axle set
PC
29
Bottle cage
PC
30
Screw for bottle cage
PC
31
Brake system
SET
32
Crank bolt
PC
33
Flywheel security nut cap
PC
90
Sensor & cable
PC

10
Maintenance Chart
No
DESCRIPTION
Daily
Weekly
Monthly
Quarterly
Annually
1
Keep machine clean: Wipe
machine down with clean & dry
fabric to clear dirt & sweat.
X
2
Spray with WD40 or similar on the
seat post set, handlebar set
(Don’t spray on the main frame)
X
3
Visual check
X
4
Check security of handle bar post
& seat post
X
5
Check security of saddle
X
6
Remove handlebar post and
clean tube
X
7
Remove seat and clean tube
X
8
Check brake pads for wear-align
X
9
Check brake adjustment
X
10
Check security of all knobs &
release lever
X
11
Check toe straps for signs of wear
X
12
Check crank bolts and re-tighten
X
13
Make sure the pedals is tighten
secure and checking weekly to
avoid loosen to cause dangerous
and damage of crank and
pedals.
X
14
Check chain tension
X
15
Oil chain
X
16
Wipe the anti-rust oil on the
flywheel
X
17
Check bottom bracket
X
18
Check flywheel bearings
X
19
Full service-frame inspection
X

11
Limited Warranty
This product carries the following guarantee against manufacturing
defects:
* Frame is warranted for 1 years from the date of purchase.
* Components are warranted for 1 year.
* Warranty is only valid for the original purchaser.
* Labor and freight charges are not included.
* Normal wear, neglect, abuse, accidents, improper assembly or
maintenance, or the installation of parts or accessories not
compatible with the original intended use of the bike, as sold, are
not covered by the warranty.
* Neither does it cover any corrosion caused by failure to clean the
bikes on regular basis.
* This warranty is limited to the repair or replacement of the defective
part at no cost. The supplier shall in no event be responsible for
consequential, special damages, and any parts failures, breakages
or injuries resulting from misuse of the machine or failure to follow
the recommended maintenance procedures.
* Warranty claims must be through an authorized dealer, and
replacement parts will normally be dispatched to you. We
recommend you held a small stock of basis spare parts, as well as a
tool kit to cover the regular maintenance routines.
* The Limited Warranty is the only express or implied warranty
applicable to original supplier. Any implied warranties, including
warranties of merchantability and fitness shall be limited in scope and
duration in accordance with this limited warranty.

12
USER MANUAL FOR CONOSLE
General:
This console has non-backlit LCD which displays Speed, RPM, Calories, Distance, Time and Pulse, optional.
Power On / Off：
The display will be active to show all data upon pedaling. Once pedaling stops, LCD will remain blinking displaying
latest data before pedaling stopped. The display will switch off if pedal stopped over 45 seconds.
Display data:
a. SPEED:
Start from 0 and plus. On Top of the LCD display showing current speed with pointer.
b. TIME:
Start from 0 and plus showing total time of this workout. Range: 00:00~99:59
c. RPM：
Rotation Per Minute. Range: 0~140. If RPM exceeds 140, LCD will show STOP for safety reason.
d. DISANCE：
Start from 0 and plus. Range: 000.0~999.9 ; Increase: 0.1 KM(ML)

13
e. CALORIES：
Start from 0 and plus showing calories consuming of this workout. Range: 000.0~999.9
f. PULSE：
For console with HR built-in receiver, bottom of the LCD showing HR. Range: 60~ 240 BPM. The chest belt must be 5K
and receiver is compatible to polar.
g. Replace the battery
Backside up.
Take the battery cover apart.
Be noted both batteries are positive end downward. Put the batteries on and cover the back cover.

14

15

16
BH Asia Ltd.
No. 80, Zhongshan Rd., Daya Dist.,
Taichung City 42841, Taiwan
Tel: [phone]
Fax: [phone]
Email: inf[email protected].tw