BH FITNESS H973 User manual

.
OWNER’S MANUAL
EXERCISE BIKE
H973
H915P

2

3
ATTENTION:
Read instructions carefully, failure to do so may cause permanent damage to your body.
Please verify that all parts associated with this product are in good condition and accounted for.
During the assembly process please be sure to follow each step accordingly as it has been
explained within the manual.

4
SAFETY INFORMATION:
1. Keep children and pets away from this equipment at all times. DO NOT leave them
unsupervised in the room where the machine is kept.
2. If you experience dizziness, nausea, chest pains or any other symptom while using
this machine STOP the exercise. SEEK IMMEDIATE MEDICALATTENTION!
3. Keep your hands away from any of the joints and moving parts.
4. Wear clothing suitable for doing exercise. Do not wear baggy clothing that might get
caught in the machine. Always wear athletic shoes when using the machine and tie
the laces securely.
5. This machine must only be used for the purposes described in this manual. DO NOT
use accessories that are not recommended.
6. Do not place sharp objects near the machine.
7. Any person with physical or coordination limitations should not use the machine
without the assistance of a qualified per son or doctor.
8. Do not use the machine if it is not working correctly.
9. Before using the machine, thoroughly inspect the equipment for proper assembly.
10. Use only authorized and trained technicians if a repair is needed.
11. Use only the tools provided to assemble this machine.
12. This machine can only be used by one person at a time.
13. The moving pedals can cause injury.
Caution: Consult your doctor before beginning to use the machine or any exercise
program. Read all of the instructions before using any exercise equipment.
KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

5
CAUTION: During assembly it is recommended that all bolts be tightened by hand,
upon completing assembly, bolts should then be properly secured using the wrench
provided. To avoid injury, check bolts carefully before use.
Assembly Drawing
STEP 1
Attach the front foot tube (35) first by lifting
up the front of the frame and sliding the front
foot tube under the frame. Align the holes of
the tube and frame then insert bolt (30) from
bottom. Tighten the nut (27) with washer (28)
and bolt (30) by the wrench.
Use the same procedure to install the rear
foot tube (31).
STEP 2
First, please remove the stopper (57) from
front end of handle bar post (13) then slip
the handlebar (46) into the handlebar post
(13), and use adjuster knob (6) to tighten
handle bar (46) on handle bar post (13).
After it, make sure to re-screw the stopper
(57) on front end of (13) handlebar post.
Attach the bottle cage (14) on the handlebar
(46) and tighten the nuts, washer and
screws (14-1) to fix it.
Insert the saddle (1) into the seat post (3)
and tighten the nuts by wrench.

6
Right Pedal
Please make sure pedal in your hand is the right pedal before
Installation. Please refer to the figure. Align the right pedal with
right crank at 90 degree. Gently insert the pedal in the crank arm.
Turn the pedals clockwise as tightly as you can with your hand.
Use the wrench to ensure it is tightened securely. Please always
tighten by hand first, then finish by wrench.
Left Pedal
Please make sure pedal in your hand is the left pedal before
Installation. Please refer to the figure. Align the left pedal with left
crank at 90 degree. Gently insert the pedal in the crank arm. Turn
the pedals counter- lockwise as tightly as you can with your
hand. Use the wrench to ensure it is tightened securely. Please
always tighten by hand first, then finish by wrench.
STEP 3
Screw the I-PAD bracket (41) onto handle
bar (46) by clamp which is on the back of
I-PAD bracket.
Attach the pedals (20) into the crank arms
(21), each pedal is marked with L (left) or R
(right) to denote the side of the spinning bike
they are on.
Note –the pedal has to work with the
same side with the crank. Be careful to
align the threads correctly to avoid
damaging them. Tighten using a 15mm
spanner; both pedals should tighten towards
the front of the spinning bike.

7
Remark:
Riding this bike backwards may loosen the pedals which will damage the threads. Please
always check pedals to ensure that the pedals are tightened. If the pedals have become loose,
tighten threads with the wrench supplied to ensure they are securely attached.
STEP 4
Insert the Monitor (49) on the I-PAD
Bracket (41) and tighten it with screw.
Connect the sensor cable (42) which
come from the handlebar post (13) with
cable on the back of monitor.
Before riding
Securely confirm all of the knobs (6) and
release lever (7), saddle(1), Pedals(20) and
screws are fastened before your training.
Stability
If the floor is not even, you can adjust the height
by front foot tube adjuster pad (36) to make it
firmly.
Adjusting the resistance
Adjust the exercise resistance on the spinning
bike which using the Tension knob (12) and
working with Level 1-16 (loosen to tighten).

8
Kind reminder:
There are the labels next to the release levers of frame. That is reminding the user
adjust the lever to proper direction to prevent interference.
Please make sure the lever direction as following before your training.
Lever for Head tube: Upward.
Lever for Seat tube: backward.
MOVING
There are moving wheel (11) located in front
foot tube for moving the machine.

9
Saddle:
Make sure tighten secure for both side of nut after adjust the
saddle position. To prevent the saddle from twisting side to
side.
Instruction
Handlebar adjustment - Adjusting the handlebar height-Undo
the adjuster release lever that is located where the handlebar
post fits into the frame. Slide the handlebar post up or down to
the required height and retighten the adjuster release lever.
Make sure it is securely tightened and that there is no lateral or
vertical movement of the handlebar. The handlebar position can
also be adjusted forwards or backwards. Slide the handlebar
assembly forwards and backwards until you reach the required
position. Then securely re-tighten the adjuster knob.
For safety concern, there is a stopper on the handlebar post
to avoid the handlebar post exceed the area can be fixed.
Seat adjustment - Undo the adjuster release lever located
where the seat post fits into the frame. Loosen the adjuster
release lever to up or down the seat post for the required
position. Then make sure the adjuster release lever tighten
securely.
For safety concern, there is a stopper on the seat post to
avoid the seat post exceed the area can be fixed.
Emergency Brake:
Pushing the lever of the Tension knob (12) forward completely
for emergency STOP.
It is important that the handlebar and seat are set at the correct
height for your body. Ask your instructor for assistance.

10
Exploded Drawing