Bianco di Puro panda User manual

Bedienungsanleitung • Instruction Manual
panda
panda
panda

EN
1
Components Overview Panda
Components Overview
1Measuring beaker
2Lid including silicone seal
3Mixing container solito
4Stainless steel blades
5Blade holder
6Cushioning mat
7Motor coupling
8Magnetic sensor for mixing container
9Motor block
10 Control panel
1
2
3
4
5
6
7
9
8
10

EN 2
Contents
COMPONENTS OVERVIEW Panda ................................................................................................................................................1
INTRODUCTION .............................................................................................................................................................................4
INFORMATION ABOUT THIS USER MANUAL ..............................................................................................................................5
SAFETY FUNCTIONS ......................................................................................................................................................................5
SAFETY PRECAUTIONS .................................................................................................................................................................6
OPERATING NOTES .......................................................................................................................................................................8
UNPACKING, CONTENTS AND START-UP ....................................................................................................................................9
REQUIREMENTS OF THE INSTALLATION LOCATION ...............................................................................................................10
ELECTRICAL CONNECTION ........................................................................................................................................................10
CONTROL PANEL OVERVIEW .....................................................................................................................................................11
OPERATING PROGRAMM BUTTONS ..........................................................................................................................................12
OPERATING bianco di puro Panda ..............................................................................................................................................13
OPERATING bianco di puro Panda WITH PRESET PROGRAMMS ..............................................................................................14
PROGRAMME DESCRIPTION ......................................................................................................................................................15
OPERATING bianco di puro Panda MANUAL MODE .................................................................................................................16
OPERATING THE TAMPER T42M .................................................................................................................................................17
MEASURING BEAKER, LID AND SEAL RING ..............................................................................................................................18
SAFETY GUIDELINES FOR CLEANING .......................................................................................................................................18
CLEANING THE MIXING CONTAINER (INCL. LID), THE MOTOR BASE AND TAMPER ...........................................................19
INSTRUCTIONS FOR GENERAL PREPARATION .........................................................................................................................20
RECIPES TO TRY - GREEN SMOOTHIES .....................................................................................................................................23
RECIPES TO TRY - TOMATO SOUP, ASPARAGUS SOUP AND CAULIFLOWER SOUP ..............................................................24

EN
3
Contents
RECIPES TO TRY - CASHEW MUSH, ALMOND MUSH .............................................................................................................. 25
RECIPES TO TRY - APRICOT PUDDING, LEMON CREAM AND NUT PUDDING ..................................................................... 26
RECIPES TO TRY - CASHEW MILK, ALMOND MILK AND HEMP MILK .................................................................................... 27
RECIPES TO TRY - TOMATO DRESSING, PEANUT DRESSING AND ZUCCHINI DRESSING ................................................... 28
RECIPES TO TRY - ICE CREAM ................................................................................................................................................... 29
RECIPES TO TRY - FRUIT SMOOTHIES ....................................................................................................................................... 30
RECIPES TO TRY - SOY MILK ...................................................................................................................................................... 31
TECHNICAL DATA ....................................................................................................................................................................... 32
DISPOSAL NOTE ......................................................................................................................................................................... 33
DISPOSAL OF USED BATTERIES ................................................................................................................................................. 34
bianco di puro CONTACTS AND CUSTOMER SERVICE ............................................................................................................. 34
INDEX .......................................................................................................................................................................................... 35
WARRANTY .................................................................................................................................................................................. 36

EN 4
Dear Customer,
We are pleased that you have decided to care for your health, with the aid of Panda!
You have bought an acknowledged quality product, and we thank you for your purchase.
Green smoothies are the perfect way for healthy nutrition. They deliver highly concentrated intrinsic in their most natural form.
These are many times higher than in conventionally prepared food.
With the Panda they are prepared in no time, taste deliciously and supply you with essential nutrients to master the daily
challenges.
True to the motto: “You are what you eat!“
We hope you enjoy your new path to healthy nutrition.
Introduction

EN
5
Information about this User Manual
Safety Functions
This user manual is part of your Panda and provides important information for start-up, safety, proper use and maintenance of
your device. The user manual must always be available with the device. It must be read by every user who deals with
start-up, operation, cleaning and maintenance
of your Panda.
Your Panda has 3 safety functions in order to protect third parties and the device from damage.
Overheating protection
The motor of your Panda is equipped with a temperature control. If the motor or the blades turn too slowly due to too solid
foods or too little uid, there is a danger of overheating. If the motor should switch off for that reason, the overheating
protection of your Panda is activated. Let your Panda cool off for about 45 minutes in a well-ventilated area, afterwards you
can use your Panda as usual.
Overload protection
The motor coupling is provided with a predetermined breaking point. This protects the motor in case the blades in the mixing
container are not able to rotate because of a blockage (forgotten items in the blender, such as spoons etc.). This predetermined
breaking point can be replaced by our bianco di puro customer service.
Sensor for mixing container
The sensor for the mixing container detects when the container has been set up correctly. If the container is not or has not been
placed correctly onto the motorblock, your Panda will not turn on. Never attempt to bypass the sensor to protect yourself and
third parties from injuries, and to prevent damage to the device.

EN 6
Safety Precautions
Please observe the following safety precautions for the safe use of the device:
• Check the Panda before the rst use for externally visible damage of the housing, electrical connection as well as the
power plug. Do not operate a damaged device.
• In case of damage to the power supply cord, the device must not be put into operation.
• If water or another uid has entered the motor base, contact your bianco di puro service as soon as possible. Disconnect
the power plug and do not operate the device any more.
• Never place the power plug in water or other uids, never wipe the power plug with a wet or moist cloth. Never touch
the power plug with wet or moist hands.
• In case of damage to the power supply cord, it must be replaced only by the manufacturer or a service agent to avoid
a hazard.
• Repairs within the warranty period must only be carried out by the bianco di puro customer service. Incorrect repairs
can lead to considerable hazards for the user. In addition to that, the warranty is voided.
• Defective parts must only be replaced with original parts, because only original parts ensure that the safety requirements
are fullled.
• Never put your hands in mixing container during operation. It will cause injuries.
• Operate the device with the original mix container only or a matching one from the bianco di puro product range.
• Fill the mixing container only up to the maximum marking (max. marking).

EN
7
Safety Precautions
• Children and frail people must always be supervised by a person responsible for their safety, when using the Panda.
• Always store the device and the mixer attachment in a place inaccessible to children.
• Always disconnect the power cord by pulling the plug from the power socket and not by pulling the power cord.
• Make sure that the power cable is not caught anywhere, causing the device to fall and injuring people.
• Operate the device only with a lled mix container.
• Do not operate the device in direct sunlight or near other heat sources.
• Make sure during operation that the lid and measuring beaker correctly close the mix container.
• Always disconnect the power cable before cleaning moving parts.
• Pay attention to the blade unit during cleaning, the sharp blades are a risk of injury.
• Do not try to dismantle the blades from the mixing container, they are permanently xed to the device.
• Never leave the device without supervision during operation.
• To avoid injuries, never touch the bottom of the mixing container and the Motor coupling immediately after use.
• This appliance shall not be used by children.
• Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they
understand the hazards involved.
• Children shall not play with the appliance.

EN 8
Operating Notes
• If you want to prepare sauces, soups or nut milk, add the ingredients in 2 to 3 steps, depending on their hardness. The
amount should not be too little, but also not too much. Too many ingredients in one process can lead to overheating and
automatic shutdown of the motor. Wait in that case until the device cools off as described above (see page 5).
• Always keep the lid closed during the operation of your Panda. This avoids any scalding or splashes of hot foods.
• Never put your hands into the mixing container during operation to avoid injuries.
• Do not dip any objects into the mixing container during operation, since otherwise the motor, blades and other parts
of the device can be destroyed. Except for the supplied tamper that may only be used through the lid opening (Fig. [2],
page 1), since it cannot contact the blades through the opening for the measuring beaker. On page 17, you will nd the
description of the tamper.
• When preparing hot drinks, soy milk or warm soups, make especially sure that the lid is closed well and your Panda is
standing securely. It is advisable to rst with start at low speed and then to increase it gradually. Alternatively you can
either use the Pulse mode or one of the preset programs (warm soup, see page 14).
• Always pour liquids and soft ingredients rst into the mixing container and afterwards the harder ingredients, such as
ice cubes, green leaves etc.
• If the chosen program or the manual mode is nished, please wait until the blades are fully stopped before removal of
the mixing container. Otherwise the connection can be damaged.
• Overloading the mix container may cause an intensive odor. Reduce the ingredients and proceed with the preparation.
• If a singed smell exudes from the motor block, stop the device immediately and disconnect the power supply. The smell
can result from abrasion of the rubber bearing of the connection if it was not mounted correctly. In this case, please
contact your bianco di puro customer service immediately.
• When preparing thick and sticky ingredients such as dough, it can happen that the motor and the blades turn idly, this is
because an air bubble has formed in the ingredients, stop the programme and remove only the measuring beaker. Your
can remove the air bubble through the opening with the included tamper. Replace the measuring beaker and continue
the preparation.

EN
9
Unpacking, Contents and Start-up
Contents
Start-up
This device is delivered with the following components:
• this user manual
• lid (including silicon seal) with integrated measuring beaker
• solito mixing container, 2.0-liter, Tritan ™ plastic, BPA-Free
• tamper TM
• motor base Panda
Attention:
• During the start-up of the device, personal injury or property damage can occur.
• Observe the safety precautions on page 6.
• Packing materials must not be used to play with, because there is danger of suffocation.
• Before operating, make sure that the silicone seal is properly mounted on the lid and the measuring cup is inserted.
• Ensure that you have closed the mixing container with the container lid properly before operation.
!
Please proceed as follows to unpack your Panda:
• Remove the tamper and all accessories from the carton.
• Remove all packing material from the device and the accessories
• Keep the packaging material during the warranty period in order to pack appropriately for warranty case.
 Please note the warning labels on the mixer and tamper
• Do not remove any stickers on the device because they are attached for safety reasons and are required for warranty
enquiry.
• Please do not remove the stickers on the handle of the tamper. On this, the safe use of the tamper is shown.

EN 10
Requirements of the Installation Location
Electrical Connection
For the safe and faultless operation of your Panda, the installation location must full the following condition:
• The device must be placed on a level, at, solid and nonslip surface that ensures the load capacity.
• Take care that the device cannot fall over.
• Do not place a cloth under the device.
• Choose the installation location so that children cannot play with the device or reach into it and cannot pull the power
cord of the device.
• Place the unit only inside and do not operate it outdoors.
For the safe and faultless operation of the device, the following points for the electrical connection must be observed:
• Before connecting, compare the technical data of the device, voltage and frequency 220 - 240 Volts, 50/60 Hz, with your
power supply. This data must conform so that the Panda is not damaged. In case of doubt ask your electrician.
• The electrical safety can only be ensured, if it is connected to a properly installed protective earth system.
• The manufacturer takes no responsibility for damages caused by a missing or disconnected protective earth.
• Make sure that the power cable is undamaged and does not pass over hot surfaces or sharp edges.
• The power cable must not be pulled tight or under tension.
• Make sure that the power plug is properly inserted into the power socket, a loose plug can lead to overheating of the
device or electric shock.

EN
11
Control Panel Overview
Speed levels
3 Preset Programs Position Indicator
Pulse-, / On-Off button
Jog Dial (rotary)
Status indicator / stop position

EN 12
Operating Program Buttons and Jog Dial
Pulse-, ON-/OFF Button
When a preset program is selected, this button starts and stops the program. Press and hold for pusle mode.
Jog Dial
With the jog dial, you can select one of the three automatic programs or the speed settings.
The current position of the jog dial is represented by the position indicator.
Preset Programs
The preset programs has predetermined runtime and speed settings. At program end, the motor switches off automatically.
Your Panda is equipped with 3 preset programs. Turn the jog dial to the desired program and press the Pulse, ON / OFF
button to start the desired program.

EN
13
Operating Panda
Connect your Panda to a power socket with the correct electric specications. You can nd them on the type plate at the back
side of the device and in chapter “Technical Data“ on page 32. Make sure that the power plug is properly inserted into the
power socket.
Mixing Container Not Placed on Motor Base1
If no mixing container is placed on the motor base, it is in power saving mode. This mode is indicated by rapid ashing of the
status indicator.
Standby Mode2
Place the mixing container on the motor base. Now you can use your blender with 3 automatic programs, the manual mode
and pulse function. In standby mode, the status light is solid red.
Start-up
In order to use your Panda, it is necessary to place on the mixing container on the motor base properly. For safety reason,
your Panda does not start without the mixing container. If you put the mixing container on the motor base, the status light is
solid red.
iPMS
The Speed is regulates by the iPMS automatically in stages 1-5. Engine perfomance is optimised when processing solid
ingredients, as well as in the preparation of Muses. This function is automatically active in the manual mode in addition to the
3 automatic programs.
Caution: Please make sure the lid (incl. Silicone seal and measuring cup) is on the mixing container before operation.
1Power consumption: < 0.3 Watt
2Power consumption in Standyby Mode: < 0.5 Watt

EN 14
Operating Panda preset programs
Start up a preset program
To start a program, the mixing container must be placed on the motor base correctly. Use the jog dial to select the desired
program.The selected program is denoted with the position display of the jog dial. Press the Pulse ON / OFF button to start
the selected program. After completion of the active program your Panda will stop automatically.
Symbol Program Program Description Run-time Status Display
Warm Soup
Level 7 for 7 seconds, then level 10 for 3 seconds. Level
10 is maintained until the end of the program. Soft start
at startup
04:20 Min. White light
Green Smoothies
Level 10 for 20 seconds, 2 seconds stop. Level 6 for 10
seconds, 2 seconds stop. Level 10 for 40 seconds, 2
seconds stop. Level 6 for 10 seconds. Soft start at startup
01:26 Min. White light
Fruit smoothie Level 10 for 8 seconds, then 2 seconds stop.
3 repetitions. Soft start at startup 00:30 Sec. White light
Manual Mode The speed level can be set individually. White light

EN
15
Program Description
Warm soups
Through the duration of 4:20 min., the contents are heated to about 42 ° C. This makes it possible to create a tasty soup from
fruit and vegetables to the raw food standard. (approximate value - depending on the lling quantity and storage temperature
of the foods).
Green smoothies
This programme was creates especially for the preparation of green smoothies and is set up so the green leaves are nely
macerated and the essential elements are optimally unlocked.
Fruit smoothies
This is the optimal setting for classic smoothies made of fruit and some types of vegetables.
Manual Mode
Select between level 1 (1500 rpm.) To Level 10 (30,000 rpm.) from the desired speed level.
 Note
You can nd recipees in the supplied bianco di puro recipe book!

EN 16
Operating Panda Manual Mode
Manual Mode
Rotate the position indicator of the jog dial to stop position. Now turn the jog dial to the right to select the manual mode in
the speed level 1 to start. The motor will start immediately in level 1. You can change the speed between the level 1 to 10
during operation.
Exit manual mode by pressing the Pulse ON / OFF button, the motor will stop immediately and the indicator light ashes red.
To continue with further preperation, you turn the jog dial in the stop position and then select the desired speed level again
or one of the preset programs.
You can also exit manual mode by rotating the jog dial to the left to the stop position. Please note, you can also turn the
blender on and off during manual mode, using the Pulse ON / OFF button.
Pulse Mode
By pressing and holding the pulse button the blender operates at the highest speed level. Stop the Pulse mode by releasing
the pulse button. The Jog Dial must be in the stop position to operate. During the Pulse mode, the status light is solid white.
Remove the mixing container only when the blades do not rotate anymore!

EN
17
Operating the Tamper T42M
Run the tamper only through the lid opening of the measuring beaker. (see Fig. 2, page 1). Use only the provided tamper and
NO OTHER objects to press the mixing content towards the blades. The less water you use, the more you have to work with
the tamper. If you use other objects, the device can be damaged.
Overview
With the aid of the tamper you can remove any air bubbles, e.g. when preparing dough, in the mixing container, without
touching the blades. With the integrated temperature gauge you can make sure your foods are prepared gently.
To measure the temperature in the mixing container, please proceed as follows:
• Switch on the tamper with the On/Off button
• Take the measuring beaker off the lid, leave the lid on the mixing container.
• Now hold the tamper into the mixing container through the opening.
• The handle of the tamper displays the temperature in °C.
Note If the display shows the temperature in °F (Fahrenheit),
you can change into °C (Celsius) by holding the On/Off button of the tamper.
Changing the battery (Battery type: CR 2032)
• Unscrew the upper part of the housing by turning it anti-clockwise.
• Now carefully pull out the display from the tamper.
• Use a coin to remove the old battery and insert a fresh battery.
• Place the display into the grip and screw the upper part of the housing tight.
Dispose of the used old battery at the provided collection points
Temperature
On / Off button
MSolito

EN 18
Measuring Beaker, Lid and Seal Ring
Safety Guideline for Cleaning
Place the measuring beaker (Fig. [1], page1) in the opening of the lid (Fig. [2], page 1) and twist it tight towards the right.
Now, place the lid rmly on the mixing container. Turn the measuring beaker to the left to take it off and lift it off the lid.
You can remove the seal ring from the lid for easy cleaning. Please take care, that the seal ring is placed in the lid after cleaning.
This chapter provides important tips for cleaning and maintenance and care of your Panda.
Please note the following safety guidelines before and during cleaning of your Panda:
• Pull the power plug from the power socket before cleaning!
• Do not open the housing of the device under any circumstances.
• If live contacts are touched and the electrical system is charged, this can lead to an electric shock or even death.
• Never place the power plug in water for cleaning.
• Never clean the power plug with a wet cloth.
• Never touch the power plug with wet hands.

EN
19
Cleaning of the Mixing Container (incl. Lid), Motor Base and Tamper
Carefully when cleaning: The stainless steel blade can cause injury!
The mixing container is not suitable for the dishwasher!
Cleaning the mix container and lid
• The mixing container can be cleaned with a brush or sponge under running water.
• Do not use aggressive or abrasive cleaning agents or solvents.
• Clean the mixing container with a mild cleaning agent (detergent) or ll 2 cups of water into the mixing container, add some
detergent, close the lid (incl. measuring beaker) and press the Pulse button for some times.
• Always clean the mixing container directly after each use.
• The silicon seal can be removed for cleaning, make sure it is re-installed correctly.
• Do not try to dismantle the blades from the container since they are permanently xed to the mixing container.
• Do not dry the jar upside down.
Cleaning of the motor base
• Clean the motor base with a soft and moist cloth.
• Do not use any aggressive cleaning agents or solvents.
• Never immerse the motor base in water or other uids (danger of short circuit).
• Never rinse the motor base under running water (danger of short circuit).
If water has entered the motor base,
disconnect the power plug and contact your bianco di puro service immediately.
Cleaning the tamper TM
You can clean the tamper under running water and dry afterwards with a soft cloth.
Make sure the contacts are completely dry when placing the mix container to the engine block.
!