Bianco di Puro Attivo User manual

EN
1
1
2
3
4
6
5
7
8
15
10
9
11
Description Attivo
Components
1Measuring beaker
2Lid for large mixing container
3Silicone seal for lid
41.0 litre mixing container
5Stainless steel blades
6Silicone seal of the blade unit
7Blade unit (screwable)
8Anti-vibration rubber pad
9Motor coupling
10 Motor block
11 Power cable
12 Anti-slip base
13 Motor ventilation
14 Control Panel
15 Anti-vibration rubber pad
16 0.6 litre mixing container
17 Silicone seal of the lid of the 0.6 litre
mixing container
18 Lid of the 0.6 litre mixing container
1A Container locking mechanism
2A Blade unit
1A
13
14
2A
18
17
16
12

EN
2
Contents
Description Attivo ..................................................................................................................................................................... 1
Introduction................................................................................................................................................................................ 4
Information about this user manual .......................................................................................................................................... 5
Safety features ........................................................................................................................................................................... 5
Safety measures......................................................................................................................................................................... 6
Operating guidelines ................................................................................................................................................................. 8
Unpacking, scope of delivery and start-up................................................................................................................................ 9
Scope of delivery ....................................................................................................................................................................... 9
Start-up ...................................................................................................................................................................................... 9
Requirements of the installation location.................................................................................................................................. 10
Electrical connection.................................................................................................................................................................. 10
Summary control element.......................................................................................................................................................... 11
Description of the buttons and the jog-dial .............................................................................................................................. 12
Operating your Attivo............................................................................................................................................................... 13
Operation of the Attivo with automatic programmes.............................................................................................................. 14
Programme description ............................................................................................................................................................. 15
Operation of the Attivo in manual mode.................................................................................................................................. 15
Operation of the tamper TXS.................................................................................................................................................... 17
Blade unit, measuring beaker, lid inc. silicone seal ................................................................................................................... 18
Safety instructions for cleaning ................................................................................................................................................. 18
Cleaning of the mixing container (inc. lid), the blade unit, the motor block and the tamper.................................................. 19
Questions and answers about the operation ............................................................................................................................ 20
Filling of the 1.0 litre mixing container...................................................................................................................................... 22
Recipes to try - green smoothies............................................................................................................................................... 23

EN
3
Contents
Recipes to try - tomato, asparagus and cauliower soup......................................................................................................... 24
Recipes to try - cashew, almond puree...................................................................................................................................... 25
Recipes to try - apricot pudding, lemon crème and nut pudding............................................................................................. 26
Recipes to try- cashew, almond and hemp milk ........................................................................................................................ 27
Recipes to try - tomato, peanut and zucchini dressing............................................................................................................. 28
Recipes to try - ice cream recipes.............................................................................................................................................. 29
Recipes to try - fruit smoothies ................................................................................................................................................. 30
Recipes to try - soy and sesame milk......................................................................................................................................... 31
Technical data............................................................................................................................................................................. 32
Disposal guidelines .................................................................................................................................................................... 33
bianco di puro contacts and customer service.......................................................................................................................... 34
Index .......................................................................................................................................................................................... 35
Warranty regulations.................................................................................................................................................................. 36

EN
4
Dear Customer,
We are pleased that you have decided to care for your health, with the aid of Attivo!
You have bought an acknowledged quality product, and we thank you for your purchase.
Green smoothies are the perfect way for healthy nutrition. They deliver highly concentrated intrinsic in their most natural form.
These are many times higher than in conventionally prepared food.
With the Attivo they are prepared in no time, taste deliciously and supply you with essential nutrients to master the daily
challenges.
True to the motto: “You are what you eat!“
We hope you enjoy your new path to healthy nutrition.
Introduction

EN
5
Information about this User Manual
Safety features
This user manual is part of your Attivo and provides important information for start-up, safety, proper use and maintenance
of your device.
The user manual must always be available with the device. It must be read by every user who
deals with start-up, operation, cleaning and maintenance
of your Attivo.
Your Attivo has 3 safety features to prevent damage to the device and third parties.
Overheating protection
The motor of your Attivo is equipped with a temperature control. If during the operation of the mixer the blades rotate too
slowly, due to too solid food or not enough liquid, there is the danger of overheating and the motor is switched off. Disconnect
the power plug and let your Attivo cool down in a well ventilated spot for about 45 minutes, afterwards you can continue using
your Attivo as usual.
Overload protection
This protects the motor in case the blades in the jar are not able to rotate because of a blockage for example forgotten items
in the jar, such as spoon.
Sensor for mixing container
The sensor for the mixing container recognizes, if it was put on properly. If the mixing container was not put on the motor block
properly, your Attivo cannot be switched on. Never bypass the sensor, to prevent damage to the device and third parties.

EN
6
Safety Precautions
Please observe the following safety precautions for the safe use of the device:
• Check your Attivo before the rst use for visible damage of the housing and power cable inc. power plug. Do not operate
a damaged device.
• In case of damage to the power cable, the device must not be operated.
• If water or another uid has entered the motor base, contact your bianco di puro customer service soon. Disconnect the
power cable from the power socket and do not use the device any more.
• Never put the power cable inc. power plug in water or other uids. Never wipe the power plug with a wet or moist cloth.
Never touch the power plug with wet or moist hands.
• In case of damage to the power supply cord, it must be replaced only by the manufacturer or a service agent to avoid a
hazard.
• Repairs within the warranty period must only be carried out by the bianco di puro customer service. Incorrect repairs can
lead to considerable hazards for the user, additionally the warranty is voided.
• Defective components must only be replaced with original spare parts. Only original spare parts ensure that the safety
requirements are fullled.
• Never reach into the mixing container with your hands, since considerable injuries can result.
• Operate your Attivo with the supplied mixing container or a container from the bianco di puro product range.
• Fill the mixing container only up to the maximum level (see marking).
• Make sure before the assembly of the blade unit and mixing container that the seal is located on the blade unit.
• Make sure before every start-up of the mixer that the blade unit is properly screwed into the mixing container.

EN
7
Safety Precautions
• Children and frail persons must always be supervised by a person responsible for their safety, when using the Attivo.
• Always store the device and the mixer attachment in a place inaccessible to children.
• Always disconnect the power cord by pulling the plug from the power socket, not by pulling the power cord.
• Make sure that the power cord is not snagged anywhere, so the unit does not topple over and no person is harmed.
• Operate the device only with a lled mix container.
• Do not operate the device in direct sunlight or near other heat sources.
• Make sure during operation that the lid inc. seal ring and measuring beaker correctly close the mixing container.
• Always disconnect the power plug from the power supply when you clean movable parts.
• Mind the blades during cleaning, since they can cause injuries.
• Do not try to separate the blades from the blade unit, since they are rmly connected.
• Never leave the device without supervision during operation.
• Never touch the drive coupling of the motor block and the bottom of the blade unit after a mixing process, to avoid
injuries.
• This appliance shall not be used by children.
• Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they
understand the hazards involved.
• Children shall not play with the appliance.

EN
8
Operating Notes
• When you want to prepare sauces, soups or nut milk, feed the ingredients in 2 to 3 steps into the feeder, according to the
degree if hardness. The amount should not be too small, but also not too much. Too many ingredients in one process can
lead to overheating and automatic shut-down of the motor. Wait in that case until the device cools down (see image 5).
• Always keep the lid of the mixing container closed during the operation of your Attivo. This avoids any scalding or
splashes of hot foods.
• Never during operation reach into the mixing container with your hands to avoid injuries.
• Do not insert any objects into the mixing container during operation, otherwise the motor, blades and other parts of the
device can be destroyed. The exception is the supplied plunger, which is so designed that it cannot contact the blades.
Here it is important that it is only inserted through the lid opening (image [2], page 1). On page 17 you nd the description
of the tamper.
• If you want to prepare hot drinks, soy milk or warm soups, take special care that the lid inc. measuring beaker closes
the mixing container properly and your Attivo is set up safely. It is advisable to rst start at low speed and to increase it
gradually. Alternatively, you can use the pulse mode or one of the automatic programmes (warm soup; see page 14 f.).
• Always pour liquids and soft ingredients rst into the mixing container and afterwards the harder ingredients, such as
leaves/green plants, ice cubes, carrots etc.
• If the chosen programme or the manual mode is nished, wait with the removal of the mixing container until the blades
are not moving/turning, otherwise the coupling can be damaged.
• An intensive smell can occur due to overloading. Reduce the lling quantity and continue the preparation.
• If a singed smell exudes from the motor block, stop the device immediately and disconnect the power supply. The smell
can result from abrasion of the rubber bearing of the connection, if it was not mounted correctly. Please contact in this
case your bianco di puro customer service immediately.
• During preparation of sticky ingredients, such as puree, it can happen that the motor and blades turn idly. This is due to
an air bubble that has formed in the ingredients. Stop the programme and remove only the measuring beaker. You can
remove the air bubble through the opening with the included tamper. Replace the measuring beaker and continue the
preparation.

EN
9
Unpacking, scope of delivery and start-up
Contents
Start-up
Please proceed as follows to unpack your Attivo:
• Remove the tamper and all accessories from the box.
• Remove all packaging from the mixer and accessories.
• Keep, if possible, the packaging during the warranty period, to be able to properly package the device in a warranty case.
Information about the labels on the mixer and the tamper
• Please do not remove any labels, since they are applied for safety reasons and are required for any warranty claims.
• Please do not remove the sticker on the handle of the tamper. It depicts the safe use of the tamper.
The mixer is delivered with the following components:
• this user manual
• lid with integrated measuring beaker
• 1.0 litre mixing container
• Turning tool
• 0.6 litre mixing container Sport-to-go
• Tamper TXS
• Motor block Attivo
Attention:
• During the start-up of the device personal injury or property damage can occur.
• Observe the safety instructions on page 6 ff.
• Packing materials must not be used to play with, because there is danger of suffocation.
• Make sure before the mixing process that the blade unit is correctly screwed into the mixing container, the
silicone seal is properly tted to the lid and the measuring beaker is inserted.
• Make sure before mixing that the mixing container is closed with the container lid.
• Open the blade unit to release pressure from inside the bottle sport-to-go when repeat processing.
!

EN
10
Requirements of the Installation Location
Electrical Connection
For the safe and faultless operation of your Attivo the installation location must full the following conditions:
• The motor block must be placed on a level, at, solid and non-slip surface that ensures the load capacity.
• Make sure that the device cannot fall over,
• Do not place a cloth under the motor block.
• Choose the installation location so that children cannot play with the mixer or reach into it and cannot pull the power cord
of the motor block.
• Set-up the mixer only in the interior and do not operate it outside.
For a safe and faultless operation of the device, the following points for the electrical connection must be observed.:
• Before connecting, compare the technical data of the device, voltage and frequency 220 - 240 Volts, 50 - 60 Hz, with your
power supply. These data must match, so the device is not damaged. Ask you electronics expert in case of uncertainty.
• The electrical safety can only be ensured, if the motor block is connected to a properly installed protective earth system.
• The manufacturer takes to responsibility for damages caused by a missing or disconnected protective earth.
• Make sure that the power cable is undamaged and does not pass over hot surfaces or sharp edges.
• The power cable must not be pulled tight or under tension.
• Make sure that the power plug is properly inserted into the power socket. A loose power plug can lead to overheating
of the device or to electrocution.

EN
11
Summary control element
Speed levels in
manual mode
3 automatic programmes Positionsanzeige
Pulse-/On-Off button
Jog-dial (rotary control) Status display

EN
12
Description of the buttons and the jog-dial
Pulse-, ON-/OFF button
This button starts the selected programme or ended prematurely and the pulse mode is activated.
Jog-Dial
You can select one of the three automatic programmes or the speed levels with the jog-dial. The current position of the
jog-dial is depicted with the position display.
Automatic programmes
The automatic programmes include certain time and speed settings. At the end of the programme the motor switches off
automatically. Your Attivo is equipped with 3 automatic programmes. Turn the jog-dial to the desired programme and press
the pulse-, ON-/OFF button to start he selected programme.

EN
13
Operating your Attivo
Connect your Attivo to a power socket with the correct electric specications. You can nd them on the rating plate on the
back of the device and in the chapter “Technical Data” on page 32. Make sure that the power plug is properly inserted into
the power socket.
Energy saving mode1
If no mixing container is placed on the motor block, the motor block is in energy saving mode. The status display ashes red.
Switching On
For the operation of your Attivo it is necessary to place the mixing container correctly on the motor block. Without the
attached mixing container your Attivo cannot be switched on for safety reasons. The status display continuously red, when
you place the mixing container on the motor block. Your Attivo is now in standby mode.
Standby mode
In standby mode you can use your mixer. The function mode depends on the attached container. With the 1.0 litre mixing
container the function mode 1 is active. With the 0.6 litre mixing container the function mode 2 is active.
Your Attivo automatically changes from standby mode to energy saving mode after 3 Minutes of inactivity.
Function mode 1
The status display ashes brightly red. In this mode the 3 automatic programmes and all speed settings (levels 1-10) in manual
mode as well as the pulse mode are available.
Function mode 2
The status display ashes dimly red. In this function mode the motor operates only in the rst two speed levels (levels 1 and
2). The motor switches off automatically after 1:25 minute. To restart the mixing process, return the jog-dial to the position.
If required, you can start a new mixing process. Open the blade unit to release pressure from inside the bottle sport-to-go
when repeat processing.
Recognition of the mixing container
There are sensors on the motor block that recognize the mixing container and activate the particular function mode. There
must always be a matching mixing container on the motor block, so it can be switched on. Never bypass the sensors, to
prevent damage to the device and third parties.
Attention: Operate the mixing container only with a correctly assembled and attached blade unit. Turn the blade unit clockwise
with the opening handle until it is hand-tight.
1Power consumption in energy saving mode: 0.61 Watt

EN
14
Operation of the Attivo with automatic programmes
Start of an Automatic Program
To start a program the 1.0 litre mixing container must be in position and your Attivo in standby mode. Select the desired
programme with the jog-dial. The selected programme is marked with the position display of the jog-dial. Press the ON-/OFF
button to start the selected programme. After the end of the program your Attivo stops automatically.
Attention: Operate the mixer only with a correctly assembled mixing container, please also make sure that the blades are
assembled properly. Turn the blade unit clockwise until it is hand-tight.
Symbol Programme Programme sequence Duration Status display
Warm soups
Level 7 for 7 seconds, then level 10 for 3 seconds. Level 10
is kept until the end of the programme
Soft start at start of programme
04:20 min. Lights up white
Green smoothies
Level 10 for 20 seconds and 2 second stop. Level 6 for 10 sec.
2 sec. stop. Level 10 for 40 sec., 2 sec. stop.
Level 6 for 10 seconds
Soft start at start of programme
01:26 min. Lights up white
Fruit smoothie
Level 10 for 8 seconds and 2 second stop.
3 repetitions.
Soft start at start of programme
00:30 sec. Lights up white
Manual Mode
Function mode 1 Selectable speed levels 1-10 Lights up white
Manual Mode
Function mode 2
Selectable speed levels: 1 and 2
The Function Mode 2 operates in the following sequence:
Level 1: Level 1 for 3 seconds, then 2 seconds stop,
5 repetitions. Then, 60 seconds to the end.
Level 2: Level 2 for 3 seconds, then 2 seconds stop,
5 repetitions. Then, 60 seconds to the end.
01:25 Min. Lights up white

EN
15
Programme Description
Warm soups
During the runtime of 4:20 min. is heated to about 42 °C. this enables you to simply prepare a tasty soup in raw fruit and
vegetables quality (approximate values - depending on the lling quantity and storage temperature of the foods).
Green Smoothie
Use this programme to prepare green smoothies. The difference to the programme “smoothies” is that the longer mixing
period shreds the green leaves optimally.
Fruit smoothie
With this you can prepare pure fruit smoothies without green leaves
Note: You can nd recipes to try from page 23.
Operation of the Attivo in manual mode
Function mode 1
The status display ashes brightly red. In this mode the 3 automatic programmes and all speed settings (levels 1-10) in manual
mode as well as the pulse mode are available.
Function mode 2
The status display ashes dimly red. In this function mode the motor operates only in the rst two speed levels (levels 1 and
2). The motor switches off automatically after 1:25 minute. To restart the mixing process, return the jog-dial to the position.
If required, you can start the mixing process again. Open the blade unit to release pressure from inside the bottle sport-to-go
when repeat processing.
Speed level settings in manual mode
To start the manual mode, turn the jog-dial to the right to the desired speed level. To end, turn the jog-dial to the position.
If you end the manual mode by pressing the On/Off button, the status display ashes rabidly in red. To continue the mixing
process, turn the jog-dial to the position.
Please note that the selectable speed levels depend on the function mode.
Pulse button
By pressing the pulse button, the mixer operates at the highest speed level. End the pulse mode by releasing the pulse button.
To use the pulse mode the jog-dial must be in the position. During the pulse mode the status display lights up in white.
the mixing container only when the blades do not rotate anymore!

EN
16
Use of the 0.6 litre mixing container
Blade unit
The 6 stainless steel
blades are extremely
long-lasting and
durable
The optimally shred
smaller amounts of
soft material.
Sport-to-go
container
0.6 litre volume
made of BPA free
plastic. Optimal for
smaller portions of
green smoothies,
fruit smoothies,
pesto and nut milks
to go.
1. Mixing
3. Storage
2. On the go
Drinking cap
(patented)
Closes the sport-to-
go container simply
and safely for on the
way.
With extra large
drinking tube and
useful handle for
easy attachment
Airtight closure
Closes the mixing
container airtight so
that the content stays
fresh longer.
Shake the content well
before consumption.
Loosening the
blade unit
Release handle
Handle for the
easy release and
locking of the
blade unit.
User Manual

EN
17
Operating the tamper TXS
Insert the tamper only through the opening in the lid of the 1.0 litre measuring container into the measuring container (see
image 2, page 1). Use only the provided tamper and no other objects to press the mixing content towards the blades. The less
water you use, the more you have to work with the tamper. If you use other objects, the device can be damaged irreparably.
With the aid of the tamper you can remove any air bubbles in the mixing container, without touching the blades.
Note:
during use of the tamper, please make sure that the lid is placed properly on the mixing container and you insert the
tamper into the mixing container only through the opening of the measuring beaker.
Overview

EN
18
Blade unit, measuring beaker, lid inc. silicone seal
Safety Guidelines or Cleaning
Blade unit
The blade unit consists of the blade holder and the blades themselves. Both of these components are rmly connected to each
other and must only be disassembled by the bianco di puro customer service.
Release the blade unit by turning to the left from the mixing container. Us the supplied turning tool for this. To attach the blade
unit to the mixing container, turn it to the right. Us the turning tool for this as well, so the blade unit is properly attached to
the mixing container.
Measuring beaker
Place the measuring beaker (→img. [1], page2) in the opening of the lid (→img. [1], page 2) and twist it tight towards the right.
Turn the measuring beaker to the left to take it off, and lift it off the lid.
Lid with silicone seal
The lid closes the container opening with the silicone seal. You can remove the silicone seal from the lid for easy cleaning. Press
the lid hand-tight on the mixing container. Please take care that the silicone seal is placed in the lid after cleaning. Only then
the tightness of the lid is ensured.
This chapter provides important tips for cleaning and maintenance and care of your Attivo.
Please note the following safety guidelines before and during cleaning of your Attivo:
• Pull the power plug from the power socket before cleaning.
• Do not open the housing of the device under any circumstances,
• If live contacts are touched and the electrical system is changed, this can lead to an electric shock or even death.
• Never place the power plug in water for cleaning,
• Never clean the power plug with a wet cloth,
• Never touch the power plug with wet hands.

EN
19
Cleaning of the mixing containers (inc. lid), the blade unit, the motor block and the tamper
Careful when cleaning: The blades can cause injuries!
The blade unit does not belong in the dishwasher!
Cleaning of the mixing container and lid
• The mixing container can be cleaned with a brush or sponge under running water,
• Do not use aggressive or abrasive cleaning agents or solvents.
• Clean the mixing container with a mild cleaning agent (detergent) or ll 2 cups of water into the mixing container, add
some detergent, close the lid (inc. measuring beaker) and press the pulse button several times.
• Always clean the mixing container directly after each use.
• The silicone seal of the lid can be removed for easy cleaning. Make sure before mixing that the silicone seal is correctly
mounted again.
Cleaning of the blade unit
• The blade unit can be unscrewed from the mixing container for easy cleaning. Hold the mixing container with one hand
and rotate the blade unit with the turning tool counter-clockwise.
• Dry the blade unit and the blades after cleaning with a soft cloth.,
• Make sure before the assembly of the mixing container that the seal is located on the blade unit. Now rotate the blade
unit hand-tight with the turning tool in clockwise direction. Make sure before lling the mixing container that the blade
unit and the seal are mounted properly.
Cleaning of the Motor Block
• Clean the motor block with a soft and moist cloth.
• Do not use any aggressive cleaning agents or solvents,
• Never submerge the motor base in water or other uids (danger of short circuit).
• Never rinse the motor block under running water (danger of short circuit).
Cleaning the tamper TXS
You can clean the tamper under running water and dry it afterwards with a soft cloth.
If water has entered the motor block, disconnect the power plug immediately from the power socket
and contact your bianco di puro customer support.
Take care that the blade unit is assembled properly, when putting the mixing container on the motor block.
!

EN
20
Question and Answers about the Operation
With the bianco di puro high performance mixer the preparation of many foods is very easy. One adds the ingredients to the
mixing container and selects the desired automatic programme. At once you have a yummy dessert, healthy smoothies or a
tasty warm soup and many more!
In reality it has been shown that all beginnings are difcult. Therefore, we have listed the most common questions and their
answers for you.
The mixer operates only with levels 1 and 2
When you use the 0.6 litre mixing container sport-to-go only levels 1 and 2 are selectable. If you want to use the automatic
programmes, please use the 1.0 litre mixing container.
An automatic programme cannot be started
Check if the 1.0 litre mixing container is placed on the motor block. Only levels 1 and 2 are selectable, if the 0.6 litre mixing
container sport-to-go is used. Check if the large mixing container is put on properly.
If required, take the mixing container off the motor block and put it on again.
During preparation your mixer works awlessly, but then stalls.
It is possible that larger pieces of the mixture can get stuck in the lower part of the mixing container. Switch the unit off and
try to loosen the large pieces with the tamper. Sometimes only an air bubble forms, which can also be removed with the
tamper. If necessary, add more water.
During mixing some of the ingredients are pushed against the mixing container and adhere there. The blades do not engage.
This mainly happens, if smaller amounts are processed as well as during the preparation of almond mousse and other nut
mousses. This can be remedied, if the mixture is pushed towards the blades with the tamper, while the device is switched
off. Adding of uid (oil) ensures that the mixture stays at the bottom of the mixing container and can be processed by the
blades. Use a lower speed level.
The mixer stalls and then gives up completely.
Your mixer is equipped with an overheating protection that makes sure your device does not overheat. Take a frequent
break, so that it can cool down. If the overheating protection is tripped, wait for about 45 minutes. After that your mixer is
ready for use as usual.