Billion SG6200NXL User manual

www.billion.com.tw
www.smartgrid.com.tw
SG6200NXL/ZigBee Single Meter
Quick Start Guide

www.billion.com.tw
www.smartgrid.com.tw
Chapter 1: Pair ZigBee Meter to SG6200NXL
Chapter 2: Network Configuration
2.1 Configuring a C in Windows 7
2.2 Configuring a C in Windows X
Chapter 3: actory Default Settings
Chapter 4: Information from your ISP
Chapter 5: Configuring with your Web Browser
5.1 Internet connection
5.1.1 EWN
5.1.2 3G
5.1.3 Wireless Client
5.1.4 Wireless
5.2 Wireless Configuration
Chapter 6: Energy Management of WEB GUI
6.1 ZigBee Configuration
6.2 Remote Control
6.3 Remote Metering
Chapter 7: SG3010-T1/SG3015-T1 Testing
7.1 Quick Installation for Testing
7.2 ZigBee Configuration
7.3 Remote Control
7.4 Remote Metering
Chapter 8: SG3010-T2/SG3015-T2 Testing
8.1 Quick Installation for Testing
8.2 ZigBee Configuration
8.3 Remote Control
8.4 Remote Metering

www.billion.com.tw
www.smartgrid.com.tw
Chapter 9: SG3010-T3/SG3015-T3 Testing
9.1 Quick Installation for Testing
9.2 ZigBee Configuration
9.3 Remote Metering
Chapter 10: SG3010-T4/SG3015-T4 Testing
10.1 Quick Installation for Testing
10.2 ZigBee Configuration
10.3 Remote Metering
Chapter 11: SG3010-iCB Testing
11.1 Quick Installation for Testing
11.2 ZigBee Configuration
11.3 Remote Control
11.4 Remote Metering
Chapter 11: BEsmart APP testing

www.billion.com.tw
www.smartgrid.com.tw
Chapter 1: Pair ZigBee Meter to SG6200NXL
STE 1 ower on ZigBee Meter
STE 2 Check Status LED lit green or not
If Status LED lit green that mean ZigBee Meter is waiting mode, please go STE 3
If Status LED blinking green that mean ZigBee Meter has been pair other SG6200NXL,
Before pair ZigBee Meter with SG6200NXL, please refer ZigBee Meter UM to do un-pairing.
STE 3 ush ZigBee button on the rear panel of the ZigBee Coordinator to make a connection.
STE 4 Then, ZigBee LED in the front panel will blink quickly around 60 seconds.
STE 5 The smart meter will be automatically paired and joined to the ZigBee network.
The Meter Status LED would blink slowly and steadily, indicating that the power meter is
successfully paired

www.billion.com.tw
www.smartgrid.com.tw
Chapter 2: Network Configuration
2.1Configuring a C in Windows 7
1. Go to Start. Click on
Control Panel.
2. Then click on Network and
Internet.
3. When the Network and
Sharing Center window
pops up, select and click on
Change adapter settings
on the left window panel.
4. Select the Local Area
Connection, and right click
the icon to select
Properties.

www.billion.com.tw
www.smartgrid.com.tw
5. Select Internet Protocol
Version 4 (TCP/IPv4) then
click Properties.
6. In the TCP/IPv4 properties
window, select the Obtain
an IP address
automatically and Obtain
DNS Server address
automatically radio
buttons. Then click OK to
exit the setting.
7. Click OK again in the Local
Area Connection
Properties window to apply
the new configuration.

www.billion.com.tw
www.smartgrid.com.tw
2.2Configuring a C in Windows X
1. Go to Start. Click on Control Panel.
2. Then click on Network and Internet.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and
click Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS
server address automatically radio
buttons.
6. Click OK to finish the configuration.

www.billion.com.tw
www.smartgrid.com.tw
Chapter 3: actory Default Settings
Before configuring the Billion SG6200NXL router, you need to know the following default
settings.
Web Interface: (Username and Password)
Username: admin
Password: admin
The default username and password are “admin” and “admin” respectively.
Device LAN IP settings
IP Address: 192.168.1.254
Subnet Mask: 255.255.255.0
ISP setting in WAN site
Obtain an IP Address Automatically
DHCP server
DHCP server is enabled.
Start IP Address: 192.168.1.100
IP pool counts: 100
LAN and WAN Port Addresses
The parameters of LAN and WAN ports are preset at the factory. The default values are
shown below
LAN Port WAN Port
IP address 192.168.1.254
Subnet Mask 255.255.255.0
DHCP server function Enabled in ports 1, 2 and 3
IP addresses for
distribution to PCs
100 IP addresses continuing
from 192.168.1.100 through
192.168.1.199
The DHCP function is
enabled to automatically get
the WAN port configuration
from the ISP.

www.billion.com.tw
www.smartgrid.com.tw
Chapter 4: Information from your ISP
Before configuring this device, you have to check with your ISP (Internet Service Provider)
what kind of services are provided, such as PPPoE, Obtain an IP Address Automatically,
Fixed IP address.
Gather the information as illustrated in the following table and keep it for reference.
PPPoE
Username, Password, Service Name, and Domain Name
System (DNS) IP address (it can be automatically assigned
by your ISP when you connect or be set manually).
Obtain an IP Address
Automatically
DHCP Client (it can be automatically assigned by your ISP
when you connect or be set manually).
Fixed IP Address
IP address, Subnet mask, Gateway address, and Domain
Name System (DNS) IP address (it is fixed IP address).

www.billion.com.tw
www.smartgrid.com.tw
Chapter 5: Configuring with your Web Browser
Open your web browser, enter the IP address of your SG6200NXL, which by default is
192.168.1.254, and click “Go”, a user name and password window prompt appears. Enter
the user name and password that your Administrator has set for you and select the
Account Type, then click Login. When you are authorised, you will access to the
router.The default username and password are “admin” and “admin” respectively for the
Administrator account type.

www.billion.com.tw
www.smartgrid.com.tw
5.1: Internet Connection
First of all, set internet connection via Quick start
Route
Basic->Quick Start
Set Time Zone of your country, then click Continue
Set WAN port interface, there are three kinds of WAN interface, EWAN, 3G, Wireless Client
5.1.1 EWAN
Connect mode: EWAN
Protocol: The current protocol in the device.
Click on Continue to choose the Protocol to connect with EWAN or click Jump to Wireless
Setting to use Protocol: Obtain an IP Address Automatically to connect and setup wireless
settings at the same time.

www.billion.com.tw
www.smartgrid.com.tw
Obtain an IP Address Automatically
When connecting to the ISP, Billion SG6200NXL also functions as a DHCP client. Billion
SG6200NXL can automatically obtain an IP address, subnet mask, gateway address, and
DNS server addresses if the ISP assigns this information via DHCP.
Protocol: The current protocol in the device
Click on the Continue button and wait for your connection to be connected.
If connection is successful the following image will be shown.

www.billion.com.tw
www.smartgrid.com.tw
Fixed IP Address
Select this option to set static IP information. You will need to enter in the Connection type,
IP address, Netmask, and gateway address, provided to you by your ISP. Each IP address
entered in the fields must be in the appropriate IP form, which are four IP octets separated
by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
Protocol: The current ATM protocol in the device
IP Address: Your WAN IP address. Leave this at 0.0.0.0 to automatically obtain an IP
address from your ISP.
Netmask: The default is 0.0.0.0. User can change it to other such as 255.255.255.0.Type
the subnet mask assigned to you by your ISP (if given).
Gateway: You must specify a gateway IP address (supplied by your ISP)
Click on the Continue button and wait for your connection to be connected.

www.billion.com.tw
www.smartgrid.com.tw
PPPoE
PPPoE (PPP over Ethernet) provides access control in a manner similar to dial-up services
using PPP.
Protocol: The current ATM protocol in the device
Username: Enter the username provided by your ISP. You can input up to 128
alphanumeric characters (case sensitive). This is in the format of “username@ispname”
instead of simply “username”.
Password: Enter the password provided by your ISP. You can input up to 128
alphanumeric characters (case sensitive).
Service Name: Enter a name for this connection.
IP Address: Your WAN IP address. Leave this at 0.0.0.0 to automatically obtain an IP
address from your ISP.
Auth. Protocol: Default is Auto. Your ISP advises on using Chap or Pap.
Click on the Continue button and wait for your connection to be connected.

www.billion.com.tw
www.smartgrid.com.tw
If connection is successful the following image will be shown.
5.1.2 3G
Connect mode: 3G
TEL No.: The dial string to make a GPRS / 3G user internetworking call. It may be provided
by your mobile service provider.
Username: Enter the username provided by your service provider.
APN: An APN is similar to a URL on the WWW, it is what the unit makes a GPRS / UMTS
call. The service provider is able to attach anything to an APN to create a data connection.
Requirements for APN assignment varies between different service providers. Most service
providers have an internet portal which they connect a DHCP Server to, giving you access
to the internet i.e. Some 3G operators use the APN ‘internet’ for their portal. The default
value of APN is “internet”.

www.billion.com.tw
www.smartgrid.com.tw
5.1.3 Wireless Client
1. Click SCAN to search for the available Wi-Fi device
2. Choose Wi-Fi device you want
3. Confirm the security type
4. Choose security mode
5. Choose security type
6. Click Apply, then the internet would be connected through wireless client.

www.billion.com.tw
www.smartgrid.com.tw
5.2 Set Wireless configuration
WLAN Service: Default setting is set to Enable.
ESSID: The ESSID is the unique name of a wireless access point (AP) to be distinguished
from another. For security propose, change to a unique ID name to the AP which is already
built-in to the router’s wireless interface. It is case sensitive and must not excess 32
characters. Make sure your wireless clients have exactly the ESSID as the device, in order
to get connected to your network.
Channel ID: Select the ID channel that you would like to use.
Security Mode: You can disable or enable with WPA or WEP for protecting wireless
network. The default mode of wireless security is Disable.

www.billion.com.tw
www.smartgrid.com.tw
Chapter 6: Energy management of WEB GUI
SG6200NXL build simple ZigBee Application in WEB GUI, System Integrator can monitor real time
power information and remote control ZigBee meter (SG3010, SG3015 serials) on the WEB GUI.
6.1 ZigBee Configuration
Once ZigBee Meter joined ZigBee Network, this page will show on ZigBee information.
Advance->Power Management-> Meter Config
Allow Join: SG6200NXL will start allow ZigBee node joining to ZigBee Network. (Billion API support)
Scan Meter: Show the current ZigBee nodes on the WEB GUI. (Billion API support)
Meter List: Show the EUI64 of ZigBee nodes.
Alias: Setup alias name for ZigBee nodes. (Billion API support)
Identify: Click Identify button the hidden LED will be blinking orange, it can help System Integrator
can find out right ZigBee node after ZigBee node has been installed. (Billion API support)
Remove: Remove ZigBee nodes from ZigBee Network. (Billion API support)

www.billion.com.tw
www.smartgrid.com.tw
6.2 Remote Control
Advance->Power Management-> Meter Config
Turn all ON: Turn all ZigBee nodes (within Relay) ON (Billion API support)
Turn all O : Turn all ZigBee nodes (within Relay) OFF (Billion API support)
Device ID: EUI64 of ZigBee nodes
Application Name: Base on Alias name
Status: Turn ON/OFF one ZigBee node (within Relay) (Billion API support)
Scenario: Do group control (Billion API support)
Support List:
SG3010-T1, SG3010-T2, SG3015-T1, SG3015-T2, SG3010-iCB, SG200

www.billion.com.tw
www.smartgrid.com.tw
6.3 Remote monitor
Show various power information from ZigBee Meters measured
Route
Advance->Status->Power Status
Device ID: EUI64 of ZigBee Meters
Appliance: Base on Alias Name
Power Status: The current relay status of ZigBee Meter (Billion API support)
Power information:
Show ower information include Voltage, Current, Frequency, F, Active ower, Apparent ower,
Main Energy (Billion API support)
Signal Strength: Show the Signal Strength between ZigBee nodes and next ZigBee nodes.