Billion BiPAC 7100SV User manual

BIPAC 7100SV
VoIP ADSL Modem/Router
with Single Ethernet Port
User Manual

i
Table of Contents
Chapter 1 ............................................................................... 1
INTRODUCTION ...................................................................................................1
1.1 An Overview of BIPAC 7100SV ..................................................................................1
1.2 Package Contents.......................................................................................................2
1.3 BIPAC 7100SV Features.............................................................................................2
1.4 BIPAC 7100SV Application.........................................................................................4
Chapter 2 ............................................................................... 5
USING BILLION VOIP ADSL MODEM/ROUTER ......................................................5
2.1 Cautions for Using Billion VoIP ADSL Modem/Router ................................................5
2.2 The Front LEDs...........................................................................................................5
2.3 The Rear Ports............................................................................................................6
2.4 Cabling........................................................................................................................6
Chapter 3 ............................................................................... 7
CONFIGURATION.................................................................................................7
3.1 Before Configuration ...................................................................................................7
3.2 Factory Default Settings............................................................................................14
3.2.1 Password............................................................................................................15
3.2.2 LAN and WAN Port Addresses...........................................................................15
3.3 Information from ISP .................................................................................................15
3.4 Configuring with Web Browser..................................................................................16
3.4.1 Status..................................................................................................................17
3.4.1.1 Status – ADSL Status................................................................................................18
3.4.1.1.1 ADSL Status – WAN Status .............................................................................................. 18
3.4.1.1.2 ADSL Status – ATM Status............................................................................................... 19
3.4.1.2 Status – LAN Status..................................................................................................19
3.4.1.2.1 LAN Status – TCP Status.................................................................................................. 20
3.4.1.3 Status- PPP Status....................................................................................................20
3.4.1.4 Status- Learned MAC Table......................................................................................21
3.4.1.5 Routing Table............................................................................................................22
3.4.1.6 System Log................................................................................................................22
3.4.1.7 Security Logs.............................................................................................................23
3.4.2 Quick Start..........................................................................................................24
3.4.2.1 ADSL Quick Start ......................................................................................................24
3.4.2.2 VoIP Quick Start........................................................................................................24
3.4.3 Configuration.......................................................................................................25
3.4.3.1 WAN..........................................................................................................................25
3.4.3.2 LAN............................................................................................................................29
3.4.3.3 VoIP...........................................................................................................................30
3.4.3.3.1 General Configuration ....................................................................................................... 31
3.4.3.3.2 Phone Book....................................................................................................................... 33
3.4.3.3.3 Dial Plan ............................................................................................................................ 35
3.4.3.3.4 Call Feature....................................................................................................................... 36
3.4.3.3.5 Advanced Telephony Settings........................................................................................... 37
3.4.3.3.6 Ring Tone.......................................................................................................................... 40
3.4.3.3.7 Timer.................................................................................................................................. 41
3.4.3.4 System.......................................................................................................................42
3.4.3.4.1 Password........................................................................................................................... 43
3.4.3.4.2 Time Zone.......................................................................................................................... 44

Billion BIPAC 7100SV VoIP ADSL Router
ii
3.4.3.4.3 Upgrade............................................................................................................................. 45
3.4.3.4.4 Factory Setting .................................................................................................................. 45
3.4.3.4.5 Restart............................................................................................................................... 46
3.4.3.5 Firewall......................................................................................................................47
3.4.3.5.1 Packet Filtering.................................................................................................................. 47
3.4.3.5.2 MAC Filtering..................................................................................................................... 49
3.4.3.5.3 Intrusion Detection............................................................................................................. 49
3.4.3.5.4 Block WAN Request.......................................................................................................... 50
3.4.3.6 Virtual Server.............................................................................................................51
3.4.3.7 Advanced...................................................................................................................52
3.4.3.7.1 ADSL ................................................................................................................................. 52
3.4.3.7.2 DNS................................................................................................................................... 53
3.4.3.7.3 Dynamic DNS.................................................................................................................... 54
3.4.3.7.4 NAT.................................................................................................................................... 55
3.4.3.7.5 RIP..................................................................................................................................... 57
3.4.3.7.6 Static Route....................................................................................................................... 58
3.4.3.7.7 MISC Configuration........................................................................................................... 59
3.4.3.7.8 Diagnostic Test.................................................................................................................. 60
3.4.4 Save Config ........................................................................................................62
Chapter 4 ............................................................................. 63
TROUBLESHOOTING ..........................................................................................63
Problems Starting Up the ADSL Router ....................................................................................63
Problems with the WAN Interface ............................................................................................63
Problems with the LAN Interface .............................................................................................63
Problems Connecting to a Remote Node or ISP..........................................................................63
APPENDIX............................................................................ 64
PRODUCT SUPPORT AND CONTACT INFORMATION ...............................................64

1
Chapter 1
Introduction
1.1 An Overview of BIPAC 7100SV
BIPAC 7100SV VoIP ADSL Modem/Router provides a high-speed Ethernet port for high-speed Internet
browsing. It can support downstream transmission rates of up to 8Mbps and upstream transmission rates
of up to 1024Kbps. It is compliant with Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt (G.992.1);
G.lite (G992.2); G.hs (G994.1)).
The product supports PPPoA (RFC 2364 – PPP (Point-to-Point Protocol) over ATM Adaptation Layer 5),
RFC 1483 encapsulation over ATM (bridged or routed), PPP over Ethernet (RFC 2516), and IPoA
(RFC1577) to establish a connection with ISP. The product also supports VC-based and LLC-based
multiplexing.
It is the perfect solution to connect a small group of PCs to a high-speed broadband Internet connection.
Multi-users can have high-speed Internet access simultaneously.
This product also serves as an Internet firewall, protecting your network from being accessed by outside
users. Not only provide the natural firewall function (Network Address Translation, NAT), it also provides
rich firewall features to secure user’s network. All incoming data packets are monitored and filtered.
Besides, it can also be configured to block internal users from accessing to the Internet.
The product provides two levels of security support. First, it masks LAN users’ IP addresses which are
invisible to outside users on the Internet, making it much more difficult for a hacker to target a machine on
your network. Secondly, it can block and redirect certain ports to limit the services that outside users can
access. For example, to ensure that games and other Internet applications will run properly, user can
open some specific ports for outside users to access internal services in network.
Integrated DHCP (Dynamic Host Control Protocol) services, client and server, allow multiple users to get
their IP addresses automatically on boot up from the product. Simply set local machines as a DHCP
client to accept a dynamically assigned IP address from DHCP server and reboot. Each time local
machine is powered up; the router will recognize it and assign an IP address to instantly connect it to the
LAN.
For advanced users, Virtual Service function allows the product to provide limited visibility to local
machines with specific services for outside users. An ISP (Internet Service Providers) provided IP
address can be set to the product and then specific services can be rerouted to specific computers on the
local network. For instance, a dedicated web server can be connected to the Internet via the product and
then incoming requests for HTML that are received by the product can be rerouted to the dedicated local
web server, even though the server now has a different IP address. In this example, the product is on the
Internet and vulnerable to attacks, but the server is protected.
Virtual Server can also be used to re-task services to multiple servers. For instance, the product can be
set to allow separated FTP, Web, and Multiplayer game servers to share the same Internet-visible IP
address while still protecting the servers and LAN users from hackers.
BIPAC 7100SV serves as a Public Switched Telephone Network (PSTN) handset-to-Ethernet adaptor
that enables traditional telephone devices to operate as Internet Protocol (IP) devices. It is the interface

Billion BIPAC 7100SV VoIP ADSL Router
2
between the PSTN world and the IP world acting as a residential gateway, eventually providing Internet
Telephony capability. Cost savings and ease of developing and integrating new services motivate most of
the interest in Internet telephony. Internet telephony integrates a variety of services provided by the
current Internet and the PSTN infrastructure.
BIPAC 7100SV extracts the maximum benefit from Voice over IP (VoIP) technology. It interfaces analog
telephones with IP-based telephony networks. The integration of VoIP technology and ADSL
Modem/Router is undoubtedly the most economic and practical solution to modern society.
1.2 Package Contents
1. Billion BIPAC 7100SV VoIP ADSL Modem/Router
2. One CD-ROM containing online manual
3. One Quick Start Guide
4. One RJ-11 ADSL/telephone cable
5. One CAT-5 straight LAN cable
6. One power adapter (12V DC 1.2A)
1.3 BIPAC 7100SV Features
BIPAC 7100SV ADSL Modem/Router provides the following features:
 ADSL Multi-Mode Standard: Supports downstream transmission rates of up to 8Mbps and
upstream transmission rates of up to 1024Kbps. It is compliant with Multi-Mode standard (ANSI
T1.413, Issue 2; G.dmt (G.992.1); G.lite (G992.2); G.hs (G994.1)).
 Multi-Protocol to Establish A Connection: Supports PPPoA (RFC 2364 - PPP over ATM
Adaptation Layer 5), RFC 1483 encapsulation over ATM (bridged or routed), PPP over Ethernet
(RFC 2516) and IPoA (RFC1577) to establish a connection with ISP. The product also supports VC-
based and LLC-based multiplexing.
 Quick Installation Wizard: Supports a WEB GUI page to install this device quickly. With this wizard,
an end user can enter the information easily which they from the ISP, then surf the Internet
immediately.
 Universal Plug and Play (UPnP) and UPnP NAT Traversal: This protocol is used to enable
simple and robust connectivity among stand-alone devices and PCs from many different vendors. It
makes network simple and affordable for users. UPnP architecture leverages TCP/IP and the Web
to enable seamless proximity networking in addition to control and data transfer among networked
devices. With this feature enabled, users can now connect to Net meeting or MSN Messenger
seamlessly.
 Network Address Translation (NAT): Allows multi-users to access outside resource such as
Internet simultaneously with one IP address/one Internet access account. Besides, many application
layer gateway (ALG) are supported such as web browser, ICQ, FTP, Telnet, E-mail, News, Ping and
others.
 Domain Name System (DNS) relay: Provides an easy way to map the domain name (a friendly
name for user such as www.yahoo.com) and IP address. When local machine sets its DNS server
with this router’s IP address. Then every DNS conversion request packet from the PC to this router
will be forwarded to the real DNS in outside network. After the router gets the reply, then forwards it
back to the PC.

Chapter 1 Introduction
3
 Dynamic Domain Name System (DDNS): The Dynamic DNS service allows you to alias a dynamic
IP address to a static hostname. This dynamic IP address is the WAN IP address. For example, to
use the service, you must first apply an account from this free Web server http://www.dyndns.org/.
There are more than 5 DDNS servers supported.
 PPP over Ethernet (PPPoE): Provides embedded PPPoE client function to establish a connection.
Users can get greater access speed without changing the operation concept, sharing the same ISP
account and paying for one access account. No PPPoE client software is required for local
computer. The Automatic Reconnect and Disconnect Timeout (Idle Timer) functions are provided,
too.
 Virtual Server: User can specify some services to be visible from outside users. The router can
detect incoming service request and forward it to the specific local computer to handle it. For
example, user can assign a PC in LAN acting as WEB server inside and expose it to the outside
network. Outside user can browse inside web server directly while it is protected by NAT. A DMZ
host setting is also provided to a local computer exposed to the outside network, Internet.
 Firewall: Supports SOHO firewall with NAT technology. Automatically detects and blocks the Denial
of Service (DoS) attack. Packet filtering is also supported. The hacker’s attack will be recorded
associated with timestamp in the security logging area. More firewall features will be added
continually, please visit our web site to download latest firmware.
 Dynamic Host Control Protocol (DHCP) client and server: In the WAN site, the DHCP client can
get an IP address from the Internet Server Provider (ISP) automatically. In the LAN site, the DHCP
server can allocate multiple clients IP addresses and distribute them including IP address, subnet
mask as well as DNS IP address to local computers. It provides an easy way to manage the local IP
network.
 Rich Packet Filtering: Not only filter the packet based on IP address, but also based on Port
numbers and MAC address. It will increase the performance in LAN and WAN, also provide a
higher-level security control
 SNTP: An easy way to get the network real time information from an SNTP server.
 Web based GUI:Supports web based GUI for configuration and management. It is user-friendly
and comes with on-line help. It also supports remote management capability for remote users to
configure and manage this product.

Billion BIPAC 7100SV VoIP ADSL Router
4
1.4 BIPAC 7100SV Application

5
Chapter 2
Using Billion VoIP ADSL Modem/Router
2.1 Cautions for Using Billion VoIP ADSL Modem/Router
Do not place the router under high humidity and high temperature.
Do not use the same power source for the device with other equipment.
Do not open or repair the case yourself. If the device is too hot, turn off the power
immediately and have a qualified serviceman repair it.
Avoid using this product and all accessories outdoors.
Place the product on the stable surface.
Only use the power adapter that comes with the package.
2.2 The Front LEDs
LED Meaning
PWR Lit green when power adapter is connected.
SYS When flash, it indicates that the device is working properly.
Phone Lit green when the phone is off hook.
LAN Lit green when the LAN link is connected.
ADSL When lit, it indicates that the ADSL (Line) port is connected to the DSLAM
and working properly.

Billion BIPAC 7100SV VoIP ADSL Router
6
2.3 The Rear Ports
LED Meaning
Power Switch A Power ON/OFF switch
Power Jack Connect the supplied power adapter to this jack.
Reset Press it to restore the factory default setting back.
VoIP Connect RJ-11 cable to this port when connecting to an analog phone
set.
LAN
(RJ-45
connector)
Connect the supplied Ethernet cable to this port when connecting to a
NIC (Network Interface card) in PC.
Connect an UTP Ethernet cable to this port when connecting to a LAN
such as an office or home network.
LINE
(RJ-11
connector)
Connect the supplied RJ-11 cable to this port when connecting to the
ADSL
2.4 Cabling
The most common problem associated with Ethernet is bad cabling or ADSL line. Make sure that all
connected devices are turned on. On the front of the product is a bank of LEDs. As a first check, please
verify that the PWR, LAN and ADSL LEDs are lit and SYS LED is blinking. If they are not, verify that you
are using the proper cables.
So long as the cables are connected and the LEDs are lit normally, follow “Chapter 3 Configuration”
below to modify the network settings.

7
Chapter 3
Configuration
BIPAC 7100SV can be configured with your Web browser. The web browser is included as a standard
application in following operation systems, UNIX, Linux, Mac OS, Windows 95/98/NT/2000/Me/XP, etc.
The product provides a very easy and user-friendly interface for configuration.
3.1 Before Configuration
This section describes the configuration required by LAN-attached PCs that communicate with BIPAC
7100SV, either to configure the device, or for network access. These PCs must have an Ethernet
interface installed properly, be connected to BIPAC 7100SV either directly or through a hub, and have
TCP/IP installed and configured to obtain an IP address through a DHCP server or a fixed IP address
which must be in the same subnet of BIPAC 7100SV. The default IP address of router is 192.168.1.254
and subnet mask is 255.255.255.0. The best and easy way is to configure the PC to get an IP address
from BIPAC 7100SV.
Please follow the steps below for PC’s network environment installation. Before taking the first step,
please check your PC’s network components. If your PC connects the ADSL Modem/Router through
Ethernet port, the TCP/IP protocol stack and Ethernet network adapter must be installed. If not, please
refer to MS Windows relative manuals.
Any TCP/IP capable workstation can be used to communicate with or through
BIPAC 7100SV. To configure other types of workstations, please consult the
manufacturer’s documentation.
Configuring PC in Windows XP
1. Go to Start / Control Panel (in
Classic View). In the Control Panel,
double-click on Network
Connections.
2. Double-click Local Area Connection.

Billion BIPAC 7100SV VoIP ADSL Router
8
3. In the Local Area Connection
Status window, click Properties.
4. Select Internet Protocol (TCP/IP)
and click Properties.

Chapter 3 Configuration
9
5. Select the Obtain an IP address
automatically and the Obtain DNS
server address automatically radio
buttons.
6. Click OK to finish the configuration.
Configuring PC in Windows 2000
1. Go to Start / Settings / Control
Panel. In the Control Panel, double-
click on Network and Dial-up
Connections.
2. Double-click Local Area Connection.

Billion BIPAC 7100SV VoIP ADSL Router
10
3. In the Local Area Connection
Status window, click Properties.
4. Select Internet Protocol (TCP/IP)
and click Properties.

Chapter 3 Configuration
11
5. Select the Obtain an IP address
automatically and the Obtain DNS
server address automatically radio
buttons.
6. Click OK to finish the configuration.
Configuring PC in Windows 95/98/ME
1. Go to Start / Settings / Control
Panel. In the Control Panel, double-
click on Network and choose the
Configuration tab.
2. Select TCP / IP -> NE2000
Compatible, or the name of your
Network Interface Card (NIC) in your
PC.
3. Click Properties.

Billion BIPAC 7100SV VoIP ADSL Router
12
4. Select the IP Address tab. In this
page, click the Obtain an IP address
automatically radio button.
5. Then select the DNS Configuration
tab.
6. Select the Disable DNS radio button
and click OK to finish the configuration.

Chapter 3 Configuration
13
Configuring PC in Windows NT4.0
1. Go to Start / Settings / Control
Panel. In the Control Panel, double-
click on Network and choose the
Protocols tab.
2. Select TCP/IP Protocol and click
Properties.

Billion BIPAC 7100SV VoIP ADSL Router
14
3. Select the Obtain an IP address
from a DHCP server radio button
and click OK.
3.2 Factory Default Settings
Before you configure this device, you need to know the following default settings.
1. Web Configuration
Password: There are two levels of password protection, Administrator Level and User Level.
User Name Password
Administrator Level admin password
User Level user password
2. Device IP Network settings in LAN site
IP Address: 192.168.1.254
Subnet Mask: 255.255.255.0
3. ISP setting in WAN site
Virtual Circuit 0: 1483 Routed IP LLC
4. DHCP server
DHCP server is enabled.
IP address pool from IP Address: 192.168.1.100 to IP Address: 192.168.1.199

Chapter 3 Configuration
15
3.2.1 Password
The default username and password are admin and password respectively.
If you ever forget the password to log in, you may press the RESET button up to 2
seconds to restore the factory default settings.
3.2.2 LAN and WAN Port Addresses
The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below.
LAN Port WAN Port
IP address 192.168.1.254
Subnet Mask 255.255.255.0
DHCP server function Enabled
IP addresses for
distribution to PCs
100 IP addresses continuing from
192.168.1.100 through 192.168.1.199
(Actually, it can supports up to 253 users.)
Obtain an IP address
automatically. ISP assigns
this IP address.
3.3 Information from ISP
Before configuring this device, you have to check with your ISP (Internet Service Provider) what kind of
service is provided such as PPPoE, PPPoA, RFC1483, IPoA, or PPTP-to-PPPoA Relaying.
Gather the information as illustrated in the following table and keep it for reference.
PPPoE
VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, Service
Name, and Domain Name System (DNS) IP address (it can be
automatically assigned by your ISP when you connect or be set manually).
PPPoA
VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, and
Domain Name System (DNS) IP address (it can be automatically assigned
by your ISP when you connect or be set manually).
RFC1483 Bridged VPI/VCI, VC-based/LLC-based multiplexing to use Bridged Mode.
RFC1483 Routed
VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet mask,
Gateway address, and Domain Name System (DNS) IP address (it is fixed
IP address).

Billion BIPAC 7100SV VoIP ADSL Router
16
IPoA
VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet mask,
Gateway address, and Domain Name System (DNS) IP address (it is fixed
IP address).
3.4 Configuring with Web Browser
The ADSL Modem/Router can be configured with your Web browser. The web browser is included as a
standard application in following operation systems, UNIX, Linux, Mac OS, Windows
95/98/NT/2000/Me/XP, etc. The product provides a very easy and user-friendly interface for configuration.
Open the web browser, enter the local port IP address of the ADSL Router, which default at
192.168.1.254, and click “Go” to get the login page.
There are two levels of password protection. The first level is for administrator and the second one is for
user.
If you want to configure the device with administrator level, type admin in the username field and
password in the password field. Then, click “OK” to log in. You can modify these passwords for security
and management purpose.