Billion BiPAC 7401V(G)P R4 User manual

BiPAC 7401V(G)P R4
VoIP/ (802.11g) ADSL2+
Firewall Router
Quick Start Guide

Quick Start Guide

Billion BiPAC 7401V(G)P R4 VoIP/ (802.11g) ADSL2+ Firewall Router
-1-
P
Pa ac ck ka ag ge e C Co on nt te en nt ts s
BiPAC 7401V(G)P R4 ADSL2+ Router
CD (containing manual, utility, QSG)
RJ-11 ADSL/ telephone cable
Ethernet (RJ-45) cable
One 2dBi detachable antenna (Wireless model only)
Power adapter
RJ-45 to RS-232 Console Kit
Quick Start Guide
Splitter/ Micro-filter (Optional)
Warning
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON
CD-ROM.

Do not use the
router
in high humidity or high temperatures.
Do not use the same power source for the router as other
equipment.
Do not open or repair the case yourself. If the router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.

Avoid using this
product
and all
accessories
outdoors.

Place the router on a stable surface.
Only use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.
Attention

Quick Start Guide
-2-
H
Ha ar rd dw wa ar re e O Ov ve er rv vi ie ew w
The Front LEDs
The Rear Ports
* Note: For WPS configuration, please refer to the WPS section of User Manual.
Connect
to the
ADSL
/
telephone network with
RJ-11 cable (telephone).
Press
t
he RESET button
for 6 seconds and above
to restore the factory
default settings.
Connec
t
to PC or an
office/home network of
10Mbps or 100Mbps with
UTP Ethernet cable. Port
4 can be either a LAN or
Console port at a time but
not both.
Connect
with
the
detachable antenna.
Lit
orange
when
power is ON. Lit red
means system is fail.
Lit green when the
system is ready.
Connect
to the
telephone jack on the
wall with RJ-11 cable.
Lit green when one of
LAN ports is connected to
an Ethernet device.
Blink when data is being
Transmitted / Received.
Lit Green when the device is
successfully connected to an
ADSL DSLAM. (“line sync”)
Lit green when
a
wireless
connection is
established. Flash green
when the device is
sending/receiving data.
Power ON/OFF
switch
Lit
green
when the
inbound and outbound
calls are transmitted
through PSTN.
Lit
green
when the
SIP Registration is
OK.
Connect
t
o an
analog phone
set with RJ-11
cable.
Lit red when WAN port fails to
get IP address. Lit green when
WAN port gets IP address
successfully. Lit off when
device in bridged mode or
WAN connection not present.
Lit green when the
phone is off hook.
Connect
it with
the supplied
power adapter.
Push
to trigger Wi
-
Fi
Protected Setup
function.

Billion BiPAC 7401V(G)P R4 VoIP/ (802.11g) ADSL2+ Firewall Router
-3-
H
Ha ar rd dw wa ar re e C Co on nn ne ec ct ti io on n
H
Ha ar rd dw wa ar re e I In ns st ta al ll la at ti io on n
1. Power Connection
Pl
ug the supplied power adapter to the wall jack and the other side to the router.
Please note that the plug type may differ according to different countries.
2. LAN Connection
Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the
other side to the PC’s Ethernet interface.

Quick Start Guide
-4-
3. Phone Connection
Connect RJ-11 cable to the router’s phone port and the analog phone set.
4. Line Connection
a) Connect RJ-11 cable to the router Line port and the splitter phone port.
b) Connect RJ-11 cable to the router DSL port and the splitter ADSL port.
c) Connect RJ-11 cable to the splitter Line port and the phone jack on the wall.
5. EWAN Connection
Connect RJ-45 Ethernet cable to the Ethernet port # 1 (EWAN), and connect the
other side to another alternative broadband device, such as Cable Modem, VDSL,
Fibre Modem or PON optic lines. Please refer to User Manual for detail instruction.

Billion BiPAC 7401V(G)P R4 VoIP/ (802.11g) ADSL2+ Firewall Router
-5-
6. Splitter/ Micro-filter Connection
The Splitter / Micro-filter are important for ADSL installation, they help direct
high-frequency signals to the ADSL modem & low frequency signals to the
telephone or other analogue device to prevent inter-modulation distortion & get
good speed/stable ADSL sync rate.
a) Splitter connection
If the installation has only a single telephone and a single ADSL modem, then a
splitter can be employed.
b) Micro-filter connection
If the installation has several telephones or other analog devices, then an internal
micro-filter can be employed at each analog device.
S
Se et tu up p U Ut ti il li it ty y
After you complete the hardware installation insert CD into the CD Drive to run the setup utility.
The setup utility will auto-run. Follow the step-by-step configuration wizard & it will guide you to
setting up the basic network configuration.

Quick Start Guide
-6-
C
Co on nn ne ec ct ti in ng g t to o t th he e R Ro ou ut te er r
1. Open the web browser and type http://192.168.1.254 in the browser's address box. This
number is the default IP address for this router. Press Enter.
2. A username and password window will appear. The default username is “admin”, and
password is “admin”. Press OK to proceed.
3. You will get a status report web page and main menu screen.
Please see the relevant sections of user manual for detailed instructions on how to
configure your router.
T
Tr ro ou ub bl le es sh ho oo ot ti in ng g
1. None of the LEDs are on when you turn on the router.
Check the connection between the adapter and the router. If the error persists, you may have
a hardware problem. In this case you should contact technical support.
2. Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC
connected. If it is off, check the cables between your router and the PC. Make sure you have
uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet
mask are consistent between the router and the workstations.
3. Frequent loss of ADSL line sync (disconnections).
Ensure that all other devices connected to the same telephone line as your router (e.g.
telephones, fax machines, analogue modems) have a line filter connected between them and
the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified
and licensed electrician), and ensure that all line filters are correctly installed and the right
way around. Missing line filters or line filters installed the wrong way around can cause
problems with your ADSL connection, including causing frequent disconnections. If you have
a back-to-base alarm system you should contact your security provider for a technician to
make any necessary changes.
P
Pr ro od du uc ct t S Su up pp po or rt t a an nd d C Co on nt ta ac ct t I In nf fo or rm ma at ti io on n
Most problems can be solved by referring to the Troubleshooting section in the User Manual.If
you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer
where you purchased this product.
C
Co on nt ta ac ct t B Bi il ll li io on n
WORLDWIDE
http://www.billion.com
BiPAC
740
1
V
(
G
)
P
R
4
:
V1.0
1
EN