Billion BiPAC 710C2 User manual

BIPAC-711C2 / 710C2
ADSL Modem / Router
Quick Start Guide

Billion BIPAC – 711C2 / 710C2 – ADSL Modem / Router
1
Package Contents
BIPAC-711C2 / 710C2 ADSL Router
CD-ROM containing the online manual
RJ-11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
One USB cable (for 711C2 only)
AC-DC power adapter (12VDC, 1A)
This Quick Start Guide
 Do not use the BIPAC-711C2 / 710C2 in high humidity or high
temperatures.
 Do not use the same power source for the BIPAC-711C2 / 710C2
as other equipment.
 Do not open or repair the case yourself. If the BIPAC-711C2 /
710C2 is too hot, turn off the power immediately and have it
repaired at a qualified service center.
Warning
 Place the BIPAC-711C2 / 710C2 on a stable surface.
 Only use the power adapter that comes with the package. Using
a different voltage rating power adaptor may damage the router.
A
ttention
For more detailed instructions on configuring and using
the ADSL Modem/Router, please refer to the on-line
manual.

Quick Start Guide
2
The Front LEDs
5 3 1
7 4 2
LED Meaning
1 PWR Lit green when power adapter is connected.
2 SYS When lit, it indicates that the device is working properly.
3 USB When this LED is lit, it indicates that the USB port is connected to
the PC and working properly.
4 LNK Lit green when the LAN link is connected.
5 COL Flashes green when collision happens
7 ADSL When lit, it indicates that the ADSL (Line) port is connected to the
DSLAM and working properly.
The difference between BIPAC-711C2 and 710C2 is that BIPAC-710C2
does not have USB port; the rest functions are the same as BIPAC-
711C2.

Billion BIPAC – 711C2 / 710C2 – ADSL Modem / Router
3
The Rear Ports
6 4 3 1
5 2
Port Meaning
1 Power Switch Power ON/OFF switch
2 PWR Connect the supplied power adapter to this jack.
3 LAN
(RJ-45 connector)
Connect the supplied crossover cable to this port when
connecting to a NIC (Network Interface card) in PC.
Connect an UTP Ethernet cable to this port when connecting to a
LAN such as an office or home network.
4 RESET Press it to restore the factory default setting back
5 USB
(USB connector) Connect the supplied USB cable to this port when connecting to
the PC
6 LINE
(RJ-11 connector) Connect the supplied RJ-11 cable to this port when connecting to the ADSL
BIPAC-710C2 does not have USB port.

Quick Start Guide
4
Connecting Your ADSL Modem/Router
Through Ethernet Port
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR, SYS and LAN LEDs are lit steadily
4. Follow the “Configuring the Network Properties on a PC” section on page 8 to modify the
network settings
Through USB Port (for BIPAC-711C2 only)
1. Connect the USB cable to the USB port of the device and connect the other end to the PC.
Also connect the device to the ADSL/telephone network.
2. Power on the device
3. Ensure the Power and LAN LEDs are lit
4. Follow the “Installing the USB Driver on a PC” section on page 5 to setup this device.

Billion BIPAC – 711C2 / 710C2 – ADSL Modem / Router
5
Installing the USB Driver on a PC (for BIPAC-711C2 only)
If you connect the device through USB port instead of Ethernet port, for the first time the USB
cable is connected to the PC, Windows will automatically detect the device. Follow the steps to
install the USB driver.
1. When Windows tells you that the new device has been detected, select “Install from a list or
specific location” and click “Next >”.
2. Insert the installation CD into the CD-ROM drive. Check “Search removable media” and click
“Next >”. Then, it takes seconds to search and install the software.
This section is described based on Windows XP. For other Operating
Systems such as Windows 2000/Me/98, please refer to the on-line
manual for more detailed instructions.

Quick Start Guide
6
3. When windows titled “Hardware Installation” or “Software Installation” appear, press
“Continue Anyway” to go on.
4. Then, click “Finish”
5. After a few moments, Windows will show the new device, USB ADSLAdapter, has been
detected. Select “Install from a list or specific location”. Click “Next >”.

Billion BIPAC – 711C2 / 710C2 – ADSL Modem / Router
7
6. Click “Next >” when the following figure appears.
7. When windows titled “Hardware Installation” appears, press “Continue Anyway”. Then, click
“Finish” to end installation.
8. After installing the driver, follow the next section to configure the network properties on the PC.

Quick Start Guide
8
Configuring PC in Windows XP
1. Go to Start / Control Panel (in Classic
View). In the Control Panel, double-click on
Network Connections
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.