Billion BiPAC 7401V(G)PX User manual

BiPAC 7401V(G)PX
3G/ VoIP/ (802.11g) ADSL2+
Firewall Router
Quick Start Guide

Quick Start Guide

Billion BiPAC 7401V(G)PX 3G/ VoIP/ (802.11g) ADSL2+ Firewall Router
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON
CD-ROM.
Package Contents
3G/ VoIP/ (802.11g) ADSL2+ Firewall Router
CD (containing manual, utility, and QSG)
RJ-11 ADSL/ telephone cable
Ethernet (RJ-45) cable
One 2dBi detachable antenna (Wireless model only)
Power adapter
RJ-45 to RS-232 Console Kit
This Quick Start Guide
Splitter/ Micro-filter (Optional)
zDo not use the router in high humidity or high temperatures.
zDo not use the same power source for the router as other
equipment.
zDo not open or repair the case yourself. If the router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.
zAvoid usin
g
this
p
roduct and all accessories outdoors.
Warning
zPlace the router on a stable surface.
zOnly use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.
Attention
-1-

Quick Start Guide
Hardware Overview
The Front LEDs
The Rear Ports
Connect the
supplied power
adapter to this jack
Connect this port to the
ADSL/telephone network
with the RJ-11 cable
(telephone) provided.
Press it to reset
the device or
restore to factory
default settings
Connect a UTP Ethernet
cable (Cat-5 or Cat-5e) to
one ofthe LAN ports when
connecting to a PC or an
office/home network of
10Mbps or 100Mbps.
Connect the
detachable
antennato this port.
Lit orange red when
power is ON. Lit red
means system is fail.
Lit green when the
system is ready.
Connect this port to
the telephone jack on
the wall with RJ-11
cable.
Lit when connected to an
Ethernet device.
Green for 100Mbps;
Orange for 10Mbps.
Blink when data is
Transmitted / Received.
Lit green when the
p
hone is of
f
hook.
Lit Green when the device is
successfully connected to an
ADSL DSLAM. (“line sync”)
Lit green when a
wireless connection is
established. Flash
when the device is
sending/receiving data.
Power
ON/OFF
switch
Lit when the inbound
and outbound calls
are transmitted
through PSTN.
Lit green when the
SIP Registration is
OK.
Push WPS button to
trigger Wi-Fi Protected
Setup function.
Lit red when WAN port fails
to get IP address. Lit green
when WAN port gets IP
address successfully. Lit off
when device in bridged
mode or WAN connection
not present.
Connect this port to
an analog phone set
with RJ-11 cable.
Lit green when the
USB device is ready.
Flashes when
sending/ receiving
data.
3G/ HSDPA USB
modem backup for
Internet access
-2-

Billion BiPAC 7401V(G)PX 3G/ VoIP/ (802.11g) ADSL2+ Firewall Router
-3-
Hardware Connection
Hardware Installation
1. Power Connection
Plug the supplied power adapter into the wall jack and the other side to the router.
Please note that the plug type may differ according to country.
2. LAN Connection
Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the
other side to the PC’s Ethernet interface.

Quick Start Guide
3. USB Connection
The USB 2.0 port supports 3G/ HSDPA modem connectivity: users can conveniently
access Internet via 3G, eliminating the limitations of the wired network. This solution
also employs an auto fail-over feature to ensure always-on connectivity for SOHO
users.
4. Phone Connection
Connect RJ-11 cable to the router’s phone port and the analog phone set.
5. Line Connection
a) Connect RJ-11 cable to the router Line port and the splitter phone port.
b) Connect RJ-11 cable to the router DSL port and the splitter ADSL port.
c) Connect RJ-11 cable to the splitter Line port and the phone jack on the wall.
-4-

Billion BiPAC 7401V(G)PX 3G/ VoIP/ (802.11g) ADSL2+ Firewall Router
6. EWAN Connection
Connect RJ-45 Ethernet cable to the Ethernet port # 1 (EWAN), and connect the
other side to another alternative broadband device, such as Cable Modem, VDSL,
Fibre Modem or PON optic lines. Please refer to User Manual for detail instruction.
7. Splitter/ Micro-filter Connection
The Splitter / Micro-filters are important for ADSL installation, they help ensure that
high-frequency signals are directed to the ADSL modem, and low-frequency
signals are directed to the telephone or other analog voice-channel device to
prevent inter-modulation distortion and get good speeds and stable ADSL sync
rate.
a) Splitter connection
If the installation has only a single telephone and a single ADSL modem, then a
splitter can be employed.
b) Micro-filter connection
If the installation has several telephones or other analog devices, then an internal
micro-filter can be employed at each analog device.
-5-

Quick Start Guide
Setup Utility
After you complete the hardware installation insert CD into the CD Drive to run the setup utility.
The setup utility will auto-run. Follow the step-by-step configuration wizard & it will guide you to
setting up the basic network configuration.
Connecting to the Router
1. Open the web browser and type http://192.168.1.254 in the browser's address box. This
number is the default IP address for this router. Press Enter.
2. A username and password window will appear. The default username is “admin”, and
password is “admin”. Press OK to proceed.
3. You will get a status report web page and main menu screen.
Please see the relevant sections of user manual for detailed instructions on how to
configure your router.
Troubleshooting
1. None of the LEDs are on when you turn on the router.
Check the connection between the adaptor and the router. If the error persists, you may have
a hardware problem. In this case you should contact technical support.
2. Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC
connected. If it is off, check the cables between your router and the PC. Make sure you have
uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet
mask are consistent between the router and the workstations.
3. Frequent loss of ADSL linesync (disconnections).
Ensure that all other devices connected to the same telephone line as your router (e.g.
telephones, fax machines, analogue modems) have a line filter connected between them and
the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified
and licensed electrician), and ensure that all line filters are correctly installed and the right
way around. Missing line filters or line filters installed the wrong way around can cause
problems with your ADSL connection, including causing frequent disconnections. If you have
a back-to-base alarm system you should contact your security provider for a technician to
make any necessary changes.
Product Support and Contact Information
Most problems can be solved by referring to the Troubleshooting section in the User Manual.If
you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer
where you purchased this product.
Contact Billion
WORLDWIDE
http://www.billion.com
Billion Products Registration
Billion is committed to before and after sales customer services. You will get the most out of your Billion's products
after registration. Please register online at http://www.billion.com/register to receive valuable services and support
from us.
BiPAC 7401V
(
G
)
PX: V1.00EN
-6-