Billion BiPAC 8501 R3 User manual

BiPAC 8501 R3/ 8521 R3
SHDSL.bis Firewall Bridge/ Router
Quick Start Guide

Quick Start Guide
2

Billion BiPAC 8501 R3/ 8521 R3 SHDSL.bis Firewall Bridge/Router
3
Package Contents
BiPAC 8501 R3/ 8521 R3 SHDSL.bis Firewall Bridge/ Router
CD-ROM containing the online manual
RJ-11 SHDSL/ telephone Cable (Note: BiPAC 8521 R3 contains two RJ-11 cables)
Ethernet (RJ-45) Cable
Power adapter
This Quick Start Guide
For more detailed instructions on configuring and using the
Billion SHDSL.bis Firewall Bridge/ Router, please refer to the
on-line manual.
Do not use the BiPAC 8501 R3/ 8521 R3 in high humidity or high
temperatures.
Do not use the same power source for this router as other
equipment.
Do not open or repair the case yourself. If this router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.
Avoid using this product and all accessories outdoors.
Warning
Place this router on a stable surface.
Only use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage this router.
Attention

Quick Start Guide
4
The Front LEDs of BiPAC 8501 R3
LED Status Meaning
Red Boot failure or in emergency mode
1 Power
Green System ready
Green Transmission speed at 10/100Mbps
2 Ethernet 1 ~ 4
(EWAN - LAN 4)
Blinking Data being transmitted/received
Green Blinking DSL synchronizing or waiting for DSL synchronizing
Green Successfully connected to an SHDSL DSLAM (Line Sync).
3 DSL
Off DSL cable unplugged
Green Router is IP connected and data is transmitting
Red Router is not IP connected or in Bridge mode
4 Internet
Off SHDSL connection not present.
1
2
3
4

Billion BiPAC 8501 R3/ 8521 R3 SHDSL.bis Firewall Bridge/Router
5
The Front LEDs of BiPAC 8521 R3
The Rear Ports of BiPAC 8501 R3
LED Status Meaning
Red Boot failure or in emergency mode
1 Power
Green System ready
Green Transmission speed at 10/100Mbps
2 Ethernet 1 ~ 4
(EWAN - LAN 4)
Blinking Data being transmitted/received
Green Blinking DSL synchronizing or waiting for DSL synchronizing
Green Successfully connected to an SHDSL DSLAM (Line Sync).
3 DSL 1 ~ 2
Off DSL cable unplugged
Green Router is IP connected and data is transmitting
Red Router is not IP connected or in Bridge mode
4 Internet
Off SHDSL connection not present.
1
2
3
4
1
2
4
5
3

Quick Start Guide
6
Port Meaning
1 Power Switch Power ON / OFF switch.
2 Power Connect the supplied power adapter to this jack.
3 Reset
After the device is powered on, press it 6seconds or above: to restore to factory
default settings (this is used when you cannot login to the router, e.g. forgot the
password)
4 Ethernet 1 ~ 4
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when
connecting to a PC or an office/home network of 10Mbps /100Mbps.
Note: Port #4 can be configured as a WAN Interface for Broadband connectivity.
5 DSL Connect this port to the SHDSL.bis network with the RJ-11 telephone cable
provided.
The Rear Ports of BiPAC 8521 R3
Port Meaning
1 Power Switch Power ON / OFF switch.
2 Power Connect the supplied power adapter to this jack.
3 Reset
After the device is powered on, press it 6seconds or above: to restore to factory
default settings (this is used when you cannot login to the router, e.g. forgot the
password)
4 Ethernet 1 ~ 4
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when
connecting to a PC or an office/home network of 10Mbps /100Mbps.
Note: Port #4 can be configured as a WAN Interface for Broadband connectivity.
5 DSL 1 ~ 2 Connect this port to the SHDSL.bis network with the RJ-11 telephone cable
provided.
1
2
4
5
3

Billion BiPAC 8501 R3/ 8521 R3 SHDSL.bis Firewall Bridge/Router
7
Connecting Your SHDSL.bis Bridge/ Router
1. Connect the Router to an Ethernet (Local Area Network) and the DSL (SHDSL Line).
2. Power on the device.
3. Make sure the Power, DSL and Internet LEDs are lit steadily and that the relevant Ethernet
LED are lit.

Quick Start Guide
8
Factory Default Settings
Before configuring the bridge/router, you need to know the following default settings.
Device LAN IP settings
IP Address: 192.168.1.254
Subnet Mask: 255.255.255.0
DHCP server
DHCP server is enabled.
Start IP Address: 192.168.1.100
IP pool counts: 100
Web Interface: (Username and Password)
Username: admin
Password: admin
The default username and password are “admin” and “admin” respectively.
Please see the relevant sections of on-line manual for detailed instructions
on how to configure your router.
If you ever forget the username/password to login to the router, you may
press the RESET button up to 6seconds then release it to restore the
factory default settings.

Billion BiPAC 8501 R3/ 8521 R3 SHDSL.bis Firewall Bridge/Router
9
Troubleshooting
1. None of the LEDs are on when you turn on the router.
Check the connection between the adapter and the router. If the error persists, you may have
a hardware problem. In this case you should contact technical support.
2. Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC
connected. If it is off, check the cables between your router and the PC. Make sure you have
uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet
mask are consistent between the router and the workstations.
3. Frequent loss of DSL line sync (disconnections).
Ensure that all other devices connected to the same telephone line as your router (e.g.
telephones, fax machines, analogue modems) have a line filter connected between them and
the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified
and licensed electrician), and ensure that all line filters are correctly installed and the right
way around. Missing line filters or line filters installed the wrong way around can cause
problems with your DSL connection, including causing frequent disconnections. If you have a
back-to-base alarm system you should contact your security provider for a technician to make
any necessary changes.
4. You have forgotten your router login and/or password.
Try the default login and password, please refer to User Manual. If this fails, you can restore
your router to its factory settings by holding the Reset button on the back of your router for 6
seconds or more.
Product Support and Contact Information
Most problems can be solved by referring to the Troubleshooting section in the User Manual.If
you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer
where you purchased this product.
Contact Billion
WORLDWIDE
http://www.billion.com
BiPAC 8501R3/8021R3 V.1.010