Billy Goat DL1201L User manual

Part No 812379 Form No F060711B
1
DL12/13/14/18 Owner’s Manual
BILLY GOAT DL TRUCK LOADER VACUUM
Owner's Manual
DL1201L, DL1301H, DL1401SE, DL1801V, DL1801VE
Accessories
INTAKE EXHAUST
Standard on DL units.
[8"(203mm) x 10' (3.0m)]
[10”(254mm) X 10’(3.0m)]
8” Hose P/N 811244
10” Hose P/N 791033
EXHAUST HOSE KIT
[7"(203mm) x 5' (1.5m)] flexible
hose increases exhaust
distance.
7” Flexible Hose P/N 812300
Allows the Debris loader to
hang from a vertical side
panel. (Not for use in
transport)
P/N 812260
HANGING EXTENSION KITHOSE REPLACEMENT KIT EXHAUST EXTENSION KIT
Allows the height of the
exhaust chute to be raised.
P/N 812273

Part No 812379 Form No F060711B
2
DL12/13/14/18 Owner’s Manual
CONTENTS
SPECIFICATIONS AND SOUND/VIBRATION 3
INSTRUCTIONLABELS 4
PACKING CHECKLIST ____________ 5
ASSEMBLY AND MOUNTING 6
OPERATION 7
MAINTENANCE________________________________ 8
TROUBLE SHOOTING__________________________________________________9
ILLUSTRATED PARTS & PARTS LISTS 10-12
Go to http://www.billygoat.com for French-Canadian translations of the product manuals.
Visitez http://www.billygoat.com pour la version canadienne-française des manuels de produits

Part No 812379 Form No F060711B
3
DL12/13/14/18 Owner’s Manual
Specifications
DL1201L DL1301H DL1401SE DL1801V DL1801VE
Battery (Electric Models Only)
Model
CCA @ 0°F AH Rating Length Width Height
DL14 ETX12 180 10 5.9” (150mm) 3.4” (86mm) 5.2” (132mm)
DL18
Battery not
included with
machine
U1 Group 275 19 6 7/8” (175mm) 4” (100mm) 6 1/8” (155mm)
SOUND
SOUND LEVEL 105 dB(a) at Operator Position
Sound tests were conducted in accordance with 2000/14/EEC, and were performed on 6/18/07 under the conditions listed below.
Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on the unit for the sound
power level for your model.
VIBRATION DATA VIBRATION LEVEL 0.02g
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using calibrated vibration test
equipment. Tests were performed on 7-10-07 under the conditions listed below.
Engine: HP 12 (8.95 kW) 13 (9.69 kW) 14 (9.69 kW) 18 (13.4 kW) 18 (13.4 kW)
Engine: Model HK291150124P-BPQE2 GX390U1QA2 EX400DE5030 3564420186EI 3564470288B1
Engine: Type LCT OHV HONDA SUBARU BRIGGS AND STRATTON BRIGGS AND STRATTON
Engine: Fuel Capacity 6 qt. (5.68 L) 6.9 qt. (6.5 L) 7.4 qt. (7.0 L) 9qt. (8.52 L) 9qt. (8.52 L)
Engine: Oil Capacity 0.875 qt. (0.8 L) 1.16 qt. (1.1 L) 1.3 qt. (1.2 L) 1.75 qt. (1.66 L) 1.75 qt. (1.66 L)
Total Unit Weight: 204 lbs (92.5 kg) 207 lbs (93.9 kg) 267 lbs (93.9 kg) 267 lbs (121.1 kg) 267 lbs (121.1 kg)
Max operating slope 250250250250250
Overall Height 74 7/8” (1.90m) 74 7/8” (1.90m) 74 7/8” (1.90m) 74 7/8” (1.90m) 74 7/8” (1.90m)
Overall Height with
optional trailer 91”(2.31m) 91”(2.31m) 91”(2.31m) 91”(2.31m) 91”(2.31m)
Overall Width 32 ¼” (0.82m) 32 ¼” (0.82m) 32 ¼” (0.82m) 32 ¼” (0.82m) 32 ¼” (0.82m)
Overall Length 60” (1.52m) 60” (1.52m) 60” (1.52m) 60” (1.52m) 60” (1.52m)
In compliance with
2000/14/EEC standards 121 dB(a) 121 dB(a) 121 dB(a) 121 dB(a) 121 dB(a)
Sound at operators
position 105 dB(a) 105 dB(a) 105 dB(a) 105 dB(a) 105 dB(a)
Vibration at operator
position 0.02g 0.02g 0.02g 0.02g 0.02g
General Conditions: Cloudy
Temperature: 74oF (23.2oC)
Wind Speed: 3.7 mph (21.6 kmh)
Wind Direction: South
Humidity: 83.5%
Barometric Pressure: 29.8 H
g
(
756 mm H
g)
General Conditions: Sunny
Temperature: 86oF (17oC)
Wind Speed: 13 mph (20 kph)
Wind Direction: North
Humidity: 49%
Barometric Pressure: 29.8”Hg (756mm Hg)

Part No 812379 Form No F060711B
4
DL12/13/14/18 Owner’s Manual
INSTRUCTION LABELS
The labels shown below were installed on your BILLY GOAT ®DL Vacuum. If any labels are damaged or missing, replace them before operating
this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering replacement labels. The
correct position for each label may be determined by referring to the Figure and Item numbers shown.
DANGER KEEP HANDS EAR EYE BREATHING WARNING SECURE DANGER FLYING DEBRIS
AND FEET AWAY ITEM# 31 P/N 890254 ITEM#62 P/N 790232 ITEM #61 P/N 810736
ITEM #18 P/N 400424
READ OWNERS MANUAL EXPLOSIVE FUEL LABEL SPARK ARRESTOR
ITEM #30 P/N 830301 ITEM #32 P/N 400268 ITEM #15 P/N 100252
WARNING ENGINE OVERHEAT SECURE NOZZLE DL INSTRUCT/WARN
ITEM #14 P/N 811215 ITEM #59 P/N 790232 ITEM #28 P/N 790142
ENGINE LABELS
HONDA B&S VANGUARD
WHEN OIL LEVELLOW,
ENGINE STOPS IMMEDIATELY.
OIL ALERT
HONDA MOTOR CO. , LTD. MADE IN JAPAN
READ OWNER’S MANUAL BEFORE OPERATION.
LIRE LE MANUEL D UTILISATEURAVANT USAGE.
VOR INBETRIEBNAHME UNBEDINGHT BEDIENUNGSANLEITUNG DURCHLESEN.
NO UTILIZAR SINANTES NO HABER LEIDO EL MANUAL

Part No 812379 Form No F060711B
5
DL12/13/14/18 Owner’s Manual
PACKING CHECKLIST
Your Billy Goat is shipped from the factory in one carton and is completely assembled except for the exhaust elbow,
nozzle, handle loop for nozzle, hose booms, hose bands, hose coupler, hose clamps and related hardware.
PUT OIL IN ENGINE BEFORE STARTING
READ all safety instructions before assembling unit.
TAKE CAUTION when removing the unit from the box.
PARTS BAG &
LITERATURE ASSY
Warranty card P/N- 400972, Owner’s Manual P/N-812379, General Safety and Warnings Manual P/N-
1
00
2
9
4
,
D
ec
l
a
r
at
i
o
n
o
f
Co
nf
o
rmi
ty
P
/
N-7
9
1
090
.
Parts Bag
Hardware
Boxing Parts Checklist
Exhaust Elbow PN# 812248-S qty 1
Hose Boom Assembly PN# 812245 qty 1
Boom Chain PN# 791117
Hose quick clamp 8” PN# 812254 qty 1
or Hose quick clamp 10” PN# 791064 qty 1
Band hose boom 8" PN# 810880 qty 1
or Band hose boom 10” PN# 810868 qty 1
Hose 8"x 10' DL PN# 811244 qty 1
or Hose 10”x 10’ DL PN# 791033 qty 1
Handle Nozzle PN# 791116 qty 1
Hose clamps 8" PN# 810566 Qty. 1
or Hose clamps 10” PN# 810706-01 qty 1
Nozzle DL 8” PN# 811007 qty 1
or Nozzle DL 10” PN#811005 qty 1
Engine
LCT 12 HP
Honda 13 HP
Vanguard 18 HP
Vanguard Electric 18 HP
Parts Bag & Literature Assy P/N 812252
Nut Lock 5/16-18
8160002 qty. 2
Nut Lock 1/4-20
8160001 qty. 1
54
Washer 1/4 SAE
8172007 qty. 2
Washer 5/16 Fender
8172020 qty. 4
Washer 5/16 SAE
8172008 qty. 2
57
56
Screwcap 5/16-18 X 2"
ZP 8041032 qty. 2
Screwcap 1/4-20 X 2 3/4"
ZP 8041013 qty. 1
43
60
53
52

Part No 812379 Form No F060711B
6
DL12/13/14/18 Owner’s Manual
ASSEMBLY
MOUNTING
MOUNTING: Main unit
GENERAL: Unit must be securely mounted to a trailer, truck bed,
hanging brackets, or other similar surface before use. Do not use this unit
in a freestanding position. Unit is not stable until it has been secured in
place.
Secure unit by bolting through the base of the unit and through the
mounting surface using 3/8" dia. bolts, with washers and locking nuts
(see fig. 1)
MOUNTING: Exhaust elbow
Note: this process is easier with two people, one to support the exhaust
elbow and one to attach plates and hardware.
1) Remove the bolts (item 50), washers (item 51), and nuts (item 41) from
the parts bag.
2) Place the elbow on top of the housing chute and line up with the holes
in the elbow with the housing in the desired position you want the exhaust
to go.
3) Secure the elbow to the housing with the hardware provided. Make
sure the hardware is properly tightened.
Fig. 1
Typical on
both sides
Step 1&2
Mount with
these holes
on both sides
1. SECURELY ATTACH unit to the bed of a truck, trailer, or use the hanging brackets, so that the exhaust discharges into an
enclosed container.
NOTE: This unit must be securely mounted to the bed of a truck or to a trailer before operating.
See page 14 for parts diagram to assemble
2. ATTACH hose to housing intake, using hose quick clamp (item 8) making sure to place the safety switch under the clamp (see
interlock page 12. Then slide the hose onto the housing intake and place the shut off switch under the clamp. Make sure the shut off
switch is pressed in or the vacuum will not start, and clamp the hose to the intake.
3. ASSEMBLE nozzle handle (item 11), to nozzle (item 10), using screws (item 60), fender washers (item 56), washers (item 57)
and lock nuts (item 43).
4. ATTACH assembled nozzle to hose using hose clamp (item 9). Before tightening hose clamp, position nozzle handle upward
when hose is stretched to prevent twisting load on hose assembly during operation.
5. ATTACH the hose boom (item 5) by sliding the boom through the ring on the top of housing and resting it in the cup on the top of
the housing.
6. ASSEMBLE hose band (item 13) around hose and secure chain between flanges of the hose band using capscrew (item 52),
washers (item 54), and lock nut (item 53). To adjust the hose boom height see page 11)
7. SECURELY ATTACH exhaust elbow (item 4) to the housing (see MOUNTING on page 10) with the hardware located on the
exhaust chute.
8. INSTALL BATTERY (Electric Models Only) Due to the location of the battery it is recommended that only the specified
battery be used on the DL1401SE and DL1801VE. This is due to the heat generated by the muffler and the location of the battery.
Using the wrong size battery could result in premature failure, damage to unit or personal injury. The battery needs to be within the
specification list on page 3. The U1 group or equivalent is recommended for the DL18VE (SEE PAGE 3 FOR BATTERY
SPECIFICATIONS)
9. (Electric Models Only) Attach the battery cables to the battery and secure it to the unit with the hold down strap.

Part No 812379 Form No F060711B
7
DL12/13/14/18 Owner’s Manual
ADJUSTING HOSE BOOM
Properly adjusting the boom will prevent most hose clogs from occurring and will
maximize vacuum performance by keeping the hose straight and perpendicular
to the housing (see fig. 5). Height adjustments are made by raising or lowering
one of the attachment links to a different area on the chain.
VACUUMING OPERATION
EXHAUST DIRECTION & DISTANCE: Exhaust direction and distance are controlled by
the rotation of the exhaust elbow. Typically debris is aimed to discharge to the rear of the
container. The direction of discharge is adjusted by rotating the exhaust elbow on the
housing and securing with the hardware provided.
NOTE: Elbow is heavy. Use caution when adjusting. Never stand directly under the elbow
while adjusting direction of exhaust.
Never direct exhaust into an area where bystanders may cross the path of the
debris.
INTAKE OPERATION: With machine running and fully assembled, move the nozzle in
sweeping motions over debris. Always allow air to flow into the nozzle along with the
debris. Do not completely block the nozzle when vacuuming, it will reduce performance,
and increase clogging (See figure 3).
For removal of heavier debris, or debris that is stuck to the ground, rock nozzle forward to
concentrate suction power around the debris (See figure 4).
UNCLOGGING A CLOGGED HOSE
With engine running and unit secured to a trailer, truck bed, or other similar surface,
fully stretch hose in a straight line to dislodge the clog. If the clog will not clear, turn unit
off, and allow engine to come to a complete stop. Remove hose and manually clear
hose clog. NOTE: The clogged debris may be sharp. Always wear durable gloves when
removing clog.
UNCLOGGING A CLOGGED HOUSING OR EXHAUST ELBOW
Turn engine off and wait for impeller to come to a complete stop. Disconnect spark plug
wires and battery cables. Remove the hose from the housing and determine where the
clog is located. If possible clear the clog through the intake opening. It may require
removal of the intake adaptor (item 16) to allow access to clear the housing. If clog is in
the elbow, carefully remove the elbow. Remove elbow by removing the bolts and nuts
on the elbow clamp so that the plates can be removed.
NOTE: Elbow is very heavy. Do not stand directly under elbow during removal.
Danger, the clog may contain sharp materials. Wearing durable gloves, clear the clog.
Reconnect spark plug wire.
HOSE CARE AND TIPS
To increase hose life, periodically rotate hose and reposition nozzle and coupler on
front plate of unit. This increases hose life by keeping hose from wearing only on one
side.
Keep hose as straight as possible and avoid sharp bends during operation for best pick-
up and to avoid clogs.
Never drag hose. Always remove and store hose before transporting unit.
Store hose straight and flat to maintain flexibility for next use.
THE HOSE IS A REPLACEABLE WEAR ITEM.
.
HOSE STORAGE: Storing hose in a covered area, out of sunlight and heat will prolong hose life. Do not store hose where it could
be stepped on or where other objects could crush or damage hose.
Fig. 3
Hose
Fig. 4
Hose Band.
Stretch hose out
before clamping
Fig. 5

Part No 812379 Form No F060711B
8
DL12/13/14/18 Owner’s Manual
MAINTENANCE
PERIODIC MAINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation Every use Every 5 hours (daily) Every 10 Hours Every 25 Hours
Inspect for loose, worn or damaged parts. z
Check engine oil and air filter z
Clean hose z
Engine (See Engine Manual)
Inspect battery for damage or leak z
Keep engine free of debris z
Check battery terminal for corrosion z
Check for excessive vibration z
INTERLOCK SYSTEM
With hose coupler installed (as shown in Fig. 8) the switch is open & engine is not grounded out, allowing engine to run.
IMPELLER REMOVAL
1. Wait for engine to cool and disconnect spark plug wires from the engine.
2. Remove the hose from the unit.
3. Unattach the hose from boom assembly.
4. Remove the intake housing assembly (item 16) by removing (6) locknuts (item 44). Be careful to
place intake assembly to the side without putting excess strain on safety switch wire harness
5. Remove impeller bolt (item 34), lock washer (item 35), and spacer (item 37) using 5/8" socket and
impact wrench (see fig. 6).
6. Once bolt is removed impeller should slide out freely. If the impeller doesn’t slide off freely use
penetrating oil and work the hub off using a pry bar. Do not use the pry bar on the impeller plate.
7. When impeller is free of the engine shaft, align impeller with the opening and pull it straight out of the
housing.
8. Using a new impeller bolt, washer, and lock washer, install new impeller in reverse order.
Note: Be sure that the key is in place on the engine shaft before installing impeller.
9. Tighten impeller bolt. Torque the impeller bolt to [33-38 Ft. Lbs. (45-52 N.m)]
10. Repeat steps 2 through 5 in reverse order.
11. Reinstall spark plug wires.
Fig. 8
Fig. 6
Hose must be
installed and switch
lever must engage
switch for engine to
start.
DL1801V SYSTEM
ENGINE
SWITCH
INTERLOCK
SWITCH
Spark plug
IGNITION
UNIT
Spark plug
IGNITION
UNIT
DL1201L SYSTEM
ENGINE
SWITCH
INTERLOCK
SWITCH
Spark plug
IGNITION
UNIT Throttle
stop
DL1301H SYSTEM
DL1801VE SYSTEM
Spark plug
Spark plug
IGNITION
UNIT
IGNITION
UNIT
ENGINE
SWITCH
INTERLOCK
SWITCH
DL1401SE SYSTEM

Part No 812379 Form No F060711B
9
DL12/13/14/18 Owner’s Manual
Troubleshooting
Problem Possible Cause Solution
Abnormal vibration. Loose or out of balance impeller or
loose engine Check impeller and replace if necessary. Check engine.
Will not vacuum or has poor
vacuum performance · Nozzle buried in debris. Clogged hose or exhaust. Excessive quantity of
debris.
· Withdraw nozzle from debris pile.
Unclog hose or exhaust (see pg. 11)
Allow air to feed debris.
Engine will not start. · Throttle & / or stop switch in off
position. Out of gasoline. Bad or old
gasoline. Spark plug wire
disconnected. Harness wire is bad or
disconnected from interlock switch.
Hose not installed, allowing interlock
wire to ground. Dirty air cleaner.
· Check stop switches, throttle, and
gasoline. Connect spark plug wire. Clean
or replace air cleaner. Install hose
coupler securely to the unit and check
whether interlock switch is engaged by
lever. Check harness wire connection
and replace if necessary.
Engine is locked, will not pull
over. · Debris locked against impeller. Engine problem. · See pg.11, Clearing a clogged impeller housing. Contact an engine servicing
dealer for engine problems.

Part No 812379 Form No F060711B
10
DL12/13/14/18 Owner’s Manual
PARTS DRAWING DL
40 ON
DL14SE
AND
DL18VE MODEL
53
80
79
70
67
68
31
26
48
46 43
1
30
71 69
46
36
47
27
63
DL18VE
MODEL
DL18V MODEL
63 27
47 36
46
69
71
30
1
68 67
70
43
46
48 26
31
5
50
51
28
29
61
4
41
40 38
41 32 1
43
57
12 65 53
11
9
56
60 14
59
10
618 1917
42
52
13
20
21
8
54
21
23 55 33
66
43
22
16
44 35
34
7
39
40
41
64 35
45
24
25
49 328
47
2
46
43
46
62
15 14
TO
ENGINE
ON
DL18V
MODEL
77
77
76
103

Part No 812379 Form No F060711B
11
DL12/13/14/18 Owner’s Manual
PARTS LIST
ITEM DL1201L
PART DL1301H PART DL1401SE PART DL1801V PART DL1801VE PART
NO. NO. NO. NO. NO. NO.
1 ENGINELCT 811250 1 - - - - - - - -
ENGINEHONDA - - 430366 1 - - - - - -
ENGINEVANGUARD - - - - - - 812240 1 - -
ENGINE VANGUARD ELECTRIC - - - - - - - - 812241 1
ENGINE SUBARU ELECTRIC - - - - 812369 1 - - - -
2 BASEENGINEWA 812100-S 1 812100-S 1 812100-S 1 812100-S 1 812100-S 1
3 HOUSING WA DL12/13 W/LABELS 812216-S 1 812216-S 1 - - - - - -
HOUSING WA DL18 W/LABELS - - - - 812101-S 1 812101-S 1 812101-S 1
4 ELBOW ASSY 7" DL 812248-S 1 812248-S 1 812248-S 1 812248-S 1 812248-S 1
5 BOOMWA DL 812245 1 812245 1 812245 1 812245 1 812245 1
6 CHAIN HOSEHANG DL 791117 1 791117 1 791117 1 791117 1 791117 1
7 HOSE8"X10" 811244 1 811244 1 - - - - - -
HOSE10" X 10" - - - - 791033 1 791033 1 791033 1
8 CLAMPQUICK RELEASE8" 812254 1 812254 1 - - - - - -
CLAMPQUICK RELEASE10" - - - - 791064 1 791064 1 791064 1
9 CLAMPHOSE8" 810566 1 810566 1 - - - - - -
CLAMPHOSE10" - - - - 810706-01 1 810706-01 1 810706-01 1
10 NOZZLE8" STEEL FORMED W/LABELS 811007-S 1 811007-S 1 - - - - - -
NOZZLE10" STEEL FORMEDW/LABELS - - - - 811005-S 1 811005-S 1 811005-S 1
11 HANDLENOZZLEWA DEBRIS LOADER 791116 1 791116 1 791116 1 791116 1 791116 1
12 GRIP1 1/4 I.D. X 9.5 LONG 440146 2 440146 2 440146 2 440146 2 440146 2
13 BAND HOSEBOOM8" FORMED 810880 1 810880 1 - - - - - -
BANDHOSEBOOM10" FORMED - - - - 810868 1 810868 1 810868 1
14 LABEL WARNING ENGINEOVERHEAT 811215 2 811215 2 811215 2 811215 2 811215 2
15 LABEL SPARK ARRESTOR 100252 1 100252 1 100252 1 100252 1 100252 1
16 PLATEFRONTWA DL 8" 812104-S 1 812104-S 1 - - - - - -
PLATEFRONT WA DL 10" - - - - 812103-S 1 812103-S 1 812103-S 1
17 FLAPPER WA 8" W/LABELS 812230-S 1 812230-S 1 - - - - - -
FLAPPERWA 10" W/LABELS - - - - 791102-S 1 791102-S 1 791102-S 1
18 LABEL WARNING OPEI 400424 1 400424 1 400424 1 400424 1 400424 1
19 STRAIN RELIEFHEYCO 1244 500282 1 500282 1 500282 1 500282 1 500282 1
20 LEVERHOSESWITCH 791068 1 791068 1 791068 1 791068 1 791068 1
21 SWITCH ANDHARNESS DL ASSY 791130 1 791130 1 791130 1 791130 1 791130 1
22 CONNECTORTAPINSQUEEZE 810673 1 810673 1 810673 1 - - - -
23 SPACER3/8" X 2 1/2" 900503 1 900503 1 900503 1 900503 1 900503 1
24 LINER DL12/13 812221 1 812221 1 - - - - - -
LINERDL18 - - - - 812214 1 812214 1 812214 1
25 PLATEENGINEMOUNTDL12/13 812235 1 812235 1 - - - - - -
PLATEENGINEMOUNT DL18 - - - - 812238 1 812238 1 812238 1
26 GUARDMUFFLER DL18 - - - - - - 812242 1 812242 1
27 GUARDMANIFOLDDL18 - - - - - - 812243 1 812243 1
28 LABEL DL INSTRUCTION/WARNING 790142 1 790142 1 790142 1 790142 1 790142 1
29 LABEL LOGO DL12/13/18 812213 1 812213 1 812213 1 812213 1 812213 1
30 SPACERCONTROL LIFT - - - - - - 850198 4 850198 4
31 SCREW SN#10 X 1" TYPEA SLOT HWH - - - - - - 8122066 4 8122066 4
32 LABEL WARNING FUEL EN/SP 100261 1 - - - - 100261 1 100261 1
33 IMPELLERASSY 812257-S 1 812257-S 1 - - - - - -
IMPELLER ASSY - - - - 810930 1 810930 1 810930 1
34 SCREWCAP3/8"-24 X 2 3/4" GR8. W/PATCH 790167 1 790167 1 - - - - - -
SCREWCAP3/8"-24 X 2 1/4" GR 8. - - - - - - 810932 1 810932 1
SCREWCAP3/8"-24 X 2" GR8. W/PATCH - - - - 440237 1 - - - -
TORQUE33-38 FT LBS. (45-52 N.m)
35 WASHERLOCK 3/8" 8177012 5 8177012 5 8177012 5 8177012 5 8177012 5
QTYQTYDESCRIPTION QTY QTY QTY

Part No 812379 Form No F060711B
12
DL12/13/14/18 Owner’s Manual
ITEM DL1201L
PART DL1301H PART DL1401SE PART DL1801V PART DL1801VE PART
NO. NO. NO. NO. NO. NO.
36 SCREWCAP5/16-18 X 2" HCS ZP - - - - - - 8041032 2 8041032 2
37
38 KEY 1/4 SQ X 2 3/4" 9201125 1 9201125 1 9201125 1 9201125 1 9201125 1
39 BOLT CARRIAGE3/8 -16 X 1" ZP 8024058 4 8024058 4 8024058 4 8024058 4 8024058 4
40 WASHER3/8 FLATCUT 8171004 4 8171004 4 8171004 6 8171004 4 8171004 4
41 NUT LOCK 3/8-16 HEX ZP 8160003 8 8160003 8 8160003 8 8160003 8 8160003 8
42 BOLT CARRIAGE5/16" - 18 X 3 1/2" ZP 8024050 1 8024050 1 8024050 1 8024050 1 8024050 1
43 NUT LOCK 5/16-18 HEX ZP 8160002 7 8160002 7 8160002 7 8160002 7 8160002 7
44 NUT FLANGE5/16-18 HEX ZP 350346 6 350346 6 350346 6 350346 10 350346 10
45 SCREWCAP3/8-16 X 3" HCS ZP 8041058 4 8041058 4 - - - - - -
SCREWCAP3/8-16 X 1 3/4" HCS ZP - - - - 8041053 4 8041053 4 8041053 4
46 WASHER5/16 FLATZP 8171003 8 8171003 8 8171003 8 8171003 8 8171003 8
47 SCREWCAP5/16-18 X 1 3/4" HCS ZP 8041031 4 8041031 4 8041031 4 8041031 2 8041031 2
48 SCREW SM1/4 X 3/4" TYPEAB HX WF - - - - - - 890359 2 890359 2
49 HEX WASHERFACEBOLT 3/8-16 X 3/4 791080 3 791080 3 791080 3 791080 3 791080 3
50 SCREWCAP3/8-16 X 1" HCS ZP 8041050 4 8041050 4 8041050 4 8041050 4 8041050 4
51 WASHER 3/8 SAE 8172009 8 8172009 8 8172009 8 8172009 8 8172009 8
52 SCREWCAP 1/4"-20 X2 3/4" HCS ZP 8041013 1 8041013 1 8041013 1 8041013 1 8041013 1
53 NUTLOCK 1/4-20 HEX ZP 8160001 1 8160001 1 8160001 1 8160001 1 8160001 3
NUT LOCK 3/8"-16 HEX (DL14 BATTERY BRACKET) - - - - 8160003 2 - - - -
54 WASHER 1/4-20 HEX ZP 8172007 2 8172007 2 8172007 2 8172007 2 8172007 2
55 CLAMP HOSE FUELLINE 791070 2 791070 2 791070 2 791070 2 791070 2
56 WASHER FENDER 5/16 8172020 4 8172020 4 8172020 4 8172020 4 8172020 4
57 WASHER 5/16 SAE 8172008 2 8172008 2 8172008 2 8172008 2 8172008 2
58
59 LABEL SECURE NOZZLE 790301 1 790301 1 790301 1 790301 1 790301 1
60 SCREWCAP 5/16" - 18 X 2" 8041032 2 8041032 2 8041032 2 8041032 2 8041032 2
61 LABEL FLYING DEBRIS 810736 2 810736 2 810736 2 810736 2 810736 2
62 WARNING SECURE 790232 1 790232 1 790232 1 790232 1 790232 1
63 SCREW SM 1/4 X1"DRILLPT. - - - - - - 430208 2 430208 2
64 SPACER 1" ID X 2" OD X 0.265 THK 830113 2 830113 2 - - - - - -
SPACER 1" ID X 2" OD X 0.890 THK - - - - 830112 1 - - - -
65 PLUG TUBE INSERT 1.25 OD 791056 2 791056 2 791056 2 791056 2 791056 2
66 DEBRIS REDUCER DL12/13/18 812283 1 812283 1 812283 1 812283 1 812283 1
67 THROTTLE CONTROL BLOWER - - - - - - 440013 1 440013 1
68 BRACKET MOUNT THROTTLE CONTROL - - - - - - 812280 1 812280 1
69 CABLE THROTTLE DL18 - - - - - - 812281 1 812281 1
70 SCREW MACH FLAT HD PHIL #10-24 - - - - - - 830514 2 830514 2
71 NUTLOCK #10-24 HEX - - - - - - 8164005 2 8164005 2
72 CABLE BATTERY RED 36" - - - - 812282 1 - - 812282 1
73 CABLE BATTERY BLACK 20" - - - - 812341 1 - - 812341 1
74
75 BATTERY 12 V (NOT SUPPLIED, SEE PAGE 3 - - - - REF REF - - REF REF
FOR BATTERY MODEL AND SPECIFICATIONS)
76 PIN SAFETY 800365 1 800365 1 800365 1 800365 1 800365 1
77 WASHER LOCK 1/4"EXTERNAL TOOTH - - - - - - 8181007 4 8181007 4
78 TERMINALPIGGY BACK 3/16" - - - - - - - - 890010 1
79 BRACKET BATTERY DL - - - - - - - - 812340 1
80 SCREWCAP 1/4"-20 X 1 1/4"HCS ZP - - - - - - - - 8041008 2
BOLT CARRIAGE 3/8-16 X1" ZP - - - - 8024058 2 - - - -
103 LABEL MADE IN U.S.A. 520116 1 520116 1 520116 1 520116 1 520116 1
QTYDESCRIPTION QTY QTY QTYQTY