Bio-Art 4000-S Owner's manual

www.bioart.com.br
Technical
Instructions
Manual
FACE-BOW AND
ARTICULATOR

NOTE:
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted, in any form or by any electronic, mechanical,
photocopyng, recording or other means, without the prior writen consent of
Bio-Art Equipamentos Odontológicos Ltda.
BIO-ART EQUIPAMENTOS ODONTOLÓGICOS LTDA.
Rua Teotônio Vilela, 120 - Jardim Tangará
CEP 13568-000 - São Carlos - SP - Brasil
Tel. [phone] - Fax [phone] - MS: 103682-4
Home Page: www.bioart.com.br E-mail: [email protected]
CÓD.: CMAN0014f - rev. 3 - Nov/2012
Authorised Representative in the European Community:
Obelis s.a
Boulevard Général Wahis 53
1030 Brussels, BELGIUM
Tel: +(32) 2. 732.59.54
Fax: +(32) 2.732.60.03
E-Mail : [e-mail]

CONTENTS
01 - Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01
02 - Standard Face-Bow registration procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02
2.1 - Dentate and partially dentate patients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02
2.2 - Totally edentureless patient . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04
03 - Mounting the casts on the Articulator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05
3.1 - Preparing the Articulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05
3.1.1 - Articulator Model 4000-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 05
3.1.2 - Articulator Model A7 Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06
3.1.3 - Articulator Model A7 Fix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06
3.2 - Mounting the upper cast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 07
3.2.1 - Standard Face-Bow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 07
3.3 - Interocclusal Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08
3.4 - Mounting the Mandibular Cast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08
3.5 - Particularities of the Rail Mounting Plate. . . . . . . . . . . . . . . . . . . . . . . . . . . 09
04 - Special features of the Bio-Art Articulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
05 - Special features of the Standard Face-Bow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
06 - Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
07 - Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
08 - Technical Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
09 - Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
10 - Part List Articulator 4000-S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
11 - Part List Articulator A7 Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
12 - Part List Articulator A7 Fix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
13 - Part List Standard Face-Bow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

1 - INTRODUCTION
IMPORTANT NOTE: Before using your BIO-ART articulator, please read carefully all the
Instructions Manual.
The articulator is an instrument used to simulate the maxillo-mandibular relation and
movements of a patient in a laboratory, with the purpose of studying the occlusion and
production of dental devices that will be used by the patient. These devices include complete
dentures, partial dentures, bridges, crowns and bite plate, among others.
The face-bow is an instrument used to register the position of the patient's dental arcade in
relation to the skull and transfer this record to the articulator.
The BIO-ART semi-adjustable articulators are Arcon type conventional equipment (models
4000-S, A7 Plus and A7 Fix) and Non-Arcon type model EVA. Therefore, the mounting
technical procedures are the same for these articulators.
This Manual contains only basic and simplified information regarding the use of the
equipment, which do not replace the need of a specific course of Occlusion and/or
Prosthesis, offered in many Teaching Institutions and Dental Faculties, as a compulsory
discipline.
IMPORTANT NOTE: The use of the equipment by professionals not qualified can cause
damage or harm to the product and/or patient.
The articulator and face-bow’s use are restricted to qualified professionals.
It is important to emphasize, however, that the semi-adjustable articulator and face-bow
provide a simple, fast and highly precise way of reproducing the human mandible movements,
enabling the dental professional to carry out corrective and restorative dentistry tasks more
easily, rapidly and at lower costs than those of traditional, time-consuming techniques
involving expensive and highly complex equipment. Furthermore, the semi-adjustable
articulator and face-bow produce far more accurate results than those produced by “simple
hinge” articulators, which involve arbitrary mounting of the mandibular cast on the device and
whose movements are also limited.
The use of the semi-adjustable articulator and face-bow is therefore recommended for most
prosthetic, occlusal and rehabilitation work. The technique is simple, fast and easy, offering
highly satisfactory results for both the patient and professional.
1

2 - STANDARD FACE-BOW REGISTRATION PROCEDURE
FIG. 1
FIG. 2
FIG. 3
FIG. 4
FIG. 5 FIG. 6 FIG. 7
2.1 - DENTATE AND PARTIALLY DENTATE PATIENTS
a) By using bite registration material (“godiva”, wax, among
others) three points on the fork are made: one frontal
point, in the exact centre of the fork, and two points at the
back, one at each semi-arch of the fork (fig.1).
b) Position the bite fork so that the midline of the fork handle
is aligned with the midline of the maxilla and place it on the
upper teeth, holding it firmly in place until the registration
material hardens (fig. 2). Only a small amount of
registration material should be used since the purpose is
to record only the cusp tips of the teeth while keeping the
fork as immobile as possible (fig. 3).
Afterwards it is advisable to try the cast on the registration
to check its stability (absence of clearance) (fig. 4).
Note: Alternatively, a pre-impression of the teeth can be
made on the upper model and then refined in the mouth.
In the case of patients who have partially jagged teeth, it is
important to locate points that hold the fork stably in place,
despite the missing teeth and the points used for the
transfer.
c) Recline the patient in the chair to reduce the induction of
tensions on the fork set and face-bow asking him to keep
the fork in the same position, supporting the thumbs
against the maxilla (fig. 5). Take the face-bow to the
patient and introduce the fork fixation assembly into the
bite fork handle, assuring that the wing nut is upside down
(fig. 6). Then carefully insert the face-bow earpieces into
the patient's external auditory meatus as if you were
putting a stethoscope into his ears (fig. 7).
2

FIG. 9
FIG. 10
FIG. 11
FIG. 12
d) Place the nasion relator on the face-bow cross bar, when
using the face-bow Standard. For both models, centre the
nosepiece on the patient's nasion. Attention to the correct
position of the nazium relator as indicated in picture 7.5b.
The earpieces should now be carefully positioned as deeply
as possible in the patient's auditory meatus and the
nosepiece should be gently pressed against the patient's
nasion while tightening the wing nuts of the nazion relator
assembly (fig. 8). Afterwards, tighten the three screws of the
Standard face-bow (fig. 9 and 14).
e) With the nazion relator and the face-bow tightened and the
patient holding the fork immobile, push the fork fixation
assembly forward, sliding it on the fork handle until it is as
close as possible to the lips, without touching them, in order
to achieve increased stability. Then tighten the wing nuts of
the fork: first the double articulated nut (connection block)
(fig. 3) and then the horizontal slide bar nut, so that the fork is
supported at one end of its handle, resulting in less tension
on it (fig. 10 and 11). To ensure proper registration, ask the
patient to remove his thumbs from the bite fork and check if
the fork and the face-bow are stable and immobilized (fig.
12).
f) When using the articulator model 4000-S, record the
approximate intercondylar distance, whose reading is taken
on the front edge of the face-bow Standard. The three
numbers (1, 2 and 3), separated by a reference mark,
correspond to the intercondylar distances: small, medium
and large. When the reference mark is aligned with the
distance indicator, always use the smallest distance for the
patient. This information should be registered in the patient´s
records for subsequent adjustment of the articulator.
In other articulator models, the intercondylar distance Note:
is fixed at an average of 110mm and the intercondylar
distance is not adjustable. In this case, disregard the above-
described registration of the face-bow.
FIG. 8
3
Wrong Position (fig. 7.5a) Correct Position (fig. 7.5b)

g) Loosen the wing nut of the nosepiece and remove the nazion relator assembly from the
face-bow. Then, loosen the central wing nut of the face-bow and hold the cross bar of the
bow at the same time the patient opens the mouth slowly, removing the whole set carefully
(fig. 15, 16 and 17)
FIG. 16
FIG. 19
FIG. 15
FIG. 18
FIG. 17
FIG. 20
2.2 - TOTALLY EDENTURELESS PATIENT
a) When registering totally edentureless patients with the face-bow, use the special
edentureless fork, or Conti fork (optional), to maintain the prove plate and roller wax.
b) After the patient's registration on the wax roller, heat both handles of the fork slightly in a
flame and press them on the upper wax roller, which was previously joined to the lower
wax roller, or not, with the midline of the fork handle aligned with the midline of the patient
(fig. 18, 19).
c) Place the set (fork + wax rollers) in the patient's mouth inserting it on the alveolar edges
(fig. 20)
Note: When carrying out the registration with wax rollers which were previously joined,
ask the patient to keep it in position and close his mouth.
d) Repeat steps (c) to (g) of item 2.1
4

3 - MOUNTING THE CASTS ON THE ARTICULATOR
3.1 PREPARING THE ARTICULATOR
The adjustments of the articulators mentioned below are
only used to mount the casts on the articulator. However,
the professional may choose to use other angulation
techniques to personalize the settings.
The marks 1, 2 and 3 of the Face Bows are used to adjust
the intercondylar distance (small, medium, large), when
the mounting is carried out with the Articulator Model
4000-S. For the other articulators models, it must be
ignored.
3.1.1 Articulator Model 4000-S
a) Fix the condylar elements into the lower frame holes
according to the patient's registration (1, 2 and 3) made
with the face-bow. With the help of the condylar element
shaft, tighten the condylar elements slightly (fig. 21).
b) Adjust the same intercondylar distance in the upper
frame, expanding or closing the condylar guide with the
micrometric expanding spindle (fig. 22).
Note: To facilitate adjustment of the intercondylar
distance of the upper frame using the micrometric spindle,
leave the wing screw of the condylar guide inclination
slightly loose.
The relationship between the intercondylar distance and
the positioning of the condylar guide is given as follows:
*Small = without expansion (condylar guide totally closed)
*Medium = first marking on the condylar guide axle
*Large = second marking on the condylar guide axle
Important: A fine adjustment should be made to prevent
lateral movements of the upper frame in relation to the
lower frame observing that the position of the condylar
elements should be touching the posterior and superior
walls of the condylar guide and the lateral of the bennet
angle adjusting device simultaneously (fig. 23) i.e., the
reference mark for the adjustment of the intercondylar
distance in the condylar guide axle does not always
coincide with the correct position of adjustment of the
upper frame. A fine adjustment is therefore necessary,
using the expanding spindle.
c) Adjust the condylar guide at a 30° angle and a negative
“Benett” angle (fig. 24 and 25), assuring the stability of the
articulator at a central position.
FIG. 21
FIG. 22
FIG. 23
FIG. 24
FIG. 25
5

FIG. 29 FIG. 30 FIG. 31
3.1.2 - Articulator Model A7 Plus
To facilitate the mounting of the casts, adjust the Condylar Guides angles at 30º and the Bennet
at 0º (fig. 29 and 30). Then push back the upper part of the central lock until feel the “click”
(locked position fig. 31).
PS.: In order to make sure that the Articulator A7 Plus is totally locked at the centric position,
check if the 2 locks (left and right) are at the locked position.
FIG. 32 FIG. 33 FIG. 34
3.1.3 - Articulator Model A7 Fix
Aiming as main characteristic simplicity and easiness to work, the A7 Fix Articulator was
developed with the Bennet and Condyle angles fixed at the average of 15° and 30°,
respectively. The intercondilar distance was also fixed at the average of 110 mm. Therefore,
this model does not require preliminary adjustments for these components, such as the other
models previously mentioned. In order to lock the Articulator A7 Fix in the centric position, there
is an innovative system with two lateral pins, denominated: “centric lock pin”. This pin has 3
main positions: first position - totally closed (locks the articulator in the centric position - picture
32); second position - intermediate (releases the articulation movements - picture 33) and third
position (allows to remove the upper from the lower frame - picture 34).
6

The Standard face-bow should only be used with the articulator
model 2000, 4000-S and 5000. It should not be used with the
EVA Fix and EVA Plus models.
a) Fix the face-bow Standard to the upper frame of the
articulator by fitting the earpiece holes on the small pins
located on the external edge of the condylar guide (fig. 39).
b) Support the front part of the Articulator Upper Frame on the
cross bar of the face-bow. Close the face-bow firmly by
fastening the central face-bow wing nut and placing the
whole face-bow together with the upper frame on the lower
frame of the articulator (fig. 40,41 and 42).
c) Place the upper cast, with retentions and previously
hydrated, on the fork registration. Lift the Upper Frame of
the articulator, depositing a small amount of plaster on the
Upper Mounting Plate and a portion on the top of the Upper
Cast. Then, using one of your hands, keep the fork and the
cast in position, avoiding any movement of the Bite Fork
and carefully hinge the Upper Frame until it touches the
cross bar of the face-bow. Wait for the plaster to harden (fig.
43).
Note: The sides of the mounting plates, which are in
contact with the articulator frames, should be devoid of
plaster.
Important: In order to achieve greater stability and
precision during the transfer procedure, it is advisable to
use the Fork Support (optional) and plaster type IV (fig. 44).
d) Remove the face-bow from the articulator.
FIG. 39
FIG. 41
FIG. 40
FIG. 43
FIG. 42 FIG. 44
Fork support (optional) Fork support (optional)
3.2 - MOUNTING THE UPPER CAST
3.2.1 Standard face-bow
7

FIG. 54
FIG. 55
3.3 - INTEROCCLUSAL REGISTRATION
To set up the mandibular (lower) cast in the articulator, you
should have a record correlating the upper and lower dental
arches, according to the purpose of the mounting, in one of
the following ways:
Maximum Intercuspation (MI);
Centric Relation (CR);
These records can be made using material of the operator's
preference: wax, resins, addition or condensation silicon, etc.
(fig. 54 and 55)
To obtain the M.I registration, place the selected material to
register the patient's arcade and ask him to occlude.
There are several techniques to obtain the R.C registration,
i.e. Peter Dawson's technique (bilateral manipulation of the
mandible), Lucia's JIG technique and James Long (use of
plastic spacer) among others.
Note: For totally edentureless patients, this registration is
made when the upper and lower wax rollers are joined based
on the correct dimensions of the patient.
3.4 - MOUNTING THE MANDIBULAR CAST
a) Place the Incisal Guide Pin in the Upper Frame of the
articulator with its rounded tip pointing downward so that
the upper and lower frames are parallel, i.e. on the zero
marking of the Incisal Guide Pin (fig. 56)
b) Now turn the articulator upside down on the laboratory
bench and affirm the lower cast, with retentions and
previously hydrated, upon the interocclusal register that
should be placed in the mounted upper cast (fig. 57). In
totally edentureless patients, this was obtained by
joining the wax rollers together.
c) We recommend fixing the casts with rubber bands or
staples (fixed with “godiva” or wax) so that they remain in
position until the plaster hardens. Place a small amount
of plaster on the lower part of the mandibular cast and a
small amount on the mounting plate of the lower frame of
the articulator to fill in the gap between them (fig. 58).
Wax registration
Silicon registration
FIG. 56
FIG. 57
FIG. 58
8

d) Make sure the condylar elements are duly positioned and
close the lower frame until the Incisal guide pin touches the
Incisal table. Afterwards, fasten the articulator frames
using rubber bands to prevent possible distortion occurred
by the plaster expansion (fig. 59)
Note: The sides of the mounting plates, which are in
contact with the articulator frames, should be devoid of
plaster.
e) After the plaster hardens, turn the articulator back to its
upright position (lower frame resting on the laboratory
bench) and complete the work, filling the cast fixation
towers with plaster for the finishing touches (fig. 60).
FIG. 59
FIG. 60
TROCAR
A FOTO
FIG. 61 FIG. 62 FIG. 63
3.5 PARTICULARITIES OF THE RAIL MOUNTING PLATE
The Rail Mounting Plate was specially developed to allow the removal of the plaster cast
without the needs of breaking it, as occurs in most of the conventional mounting plates.
In order to use of this resource satisfactorily, the professional should take some cares, mainly
during the confection of the cast, and afterwards when handling the removal of
the plate, occording to the following procedure:
a) The plaster finishing on the edge of the mounting plate should be done in such way to avoid
excess of plaster around the edge and to allow the splitting and the sliding of the plate
afterwards, i.e., during the removal procedure (fig. 61).
b) Before the removal of the cast, the plaster contained in the retention hole should be
removed with an instrumental tip. The function of this retention hole is to avoid
displacement of the plate when handling the cast (fig. 62).
c) Once the plaster contained in the retention hole is removed, the cast should be firmly held
and a slight strike must be applied on the edge of the plate, in the direction of the arrows
stamped in the plate lower face. This procedure will detach the mounting plate from the
cast and enable its removal through the sliding (fig. 63).
PS: Once the cast is removed from the rail mounting plate, we do not assure its returning to the
initial precision since it dependes on the technique applied and quality of the materials used in
the process (specially the plaster).
9

Adjustable / Curve
Silicone Connection
Fixed at 110 mm
Fixed at 110 mm
Arcon
Adjustable / Curve
Adjustable
Adjustable *
No
Elastic Band (O´ring) Magnetic
Arcon Arcon
Fixed at 15° Adjustable
Yes Yes
Curve
Fixed at 30°
4000-S A7 Fix A7 Plus
Classification Condylar Guide Bennet Angle Intercondylar Distance Central Lock Stabilization System **
Model
Features
* Adjustment made through the micrometrical
expanding spindle. (Bio-Art's exclusive system)
** Joining system between the upper and lower frames
provides stability during articulating movements.
Interchangeable Articulators (Optional)
Bio-Art's interchangeable articulators are
standardized (calibrated) by the manufacturer to allow for interchangeability of the casts among these articulator models. Only model 4000-S cannot be supplied in the standardized option.
4 - SPECIAL FEATURES OF THE BIO-ART ARTICULATORS
Mod. 4000-S
Mod. A7 Plus
Mod. A7 Fix
10

5 - SPECIAL FEATURES OF THE STANDARD FACE-BOW
5.3 - INSTRUCTIONS FOR USE THE NOSE PIECE
SUPPORT
Slide the Nose Piece Support in the Face-Bow's Cross Bar
through the groove, pressing it until realize a slight "click"
indicating that the support is fully embedded. The support
may be laterally moved, so that it can be placed in the
position desired by the operator (fig. 64).
To withdraw the Nose Piece Support, make a movement of
twist to facilitate its removal (fig. 65).
FIG. 64
FIG. 65
Magnetic Mounting
Plate
Toothless Fork
(Adjustable)
Fox RulerRail Plate Camper's Plane Exclusive Plastic Case
Adjustable Incisal Guiding
Table (Metallic)
Fork Support
6 - ACCESSORIES
11
5.1 - STANDARD FACE-BOW
The Bio-Art Standard model is simple and easy to work with. It
has manually tightened wing nuts to fix the fork, eliminating the
inconvenient use of the key. In this model, the registration of
the position of the patient's upper dental arcade in relation to
the skull is transferred to the articulator by setting the complete
face-bow in the upper frame assembly of the articulator
(chapter 3 Item 3.2.1)
The Standard Face Bow can be used with the all Articulators
models, its use is forbidden with the Models EVA Fix and EVA
Plus.

7 - SAFETY RULES
• This manual only contains basic and simplified information regarding the use of the
instrument and under no circumstances it is a substitute for a proper training course. The
articulator and face-bow are products aimed at the exclusive use of qualified dental
professionals.
• The Bio-Art face-bow is designed for use with Bio-Art's own articulator and vice-versa.
Although, the Standard face-bow is compatible with other articulator models, its use with
similar models should be consulted.
• Bio-Art articulators are not interchangeable, i.e. the casts mounted on one articulator
model should not be transferred (mounted) to any other articulator. Therefore, Bio-Art does
not guarantee precision when casts mounted on one articulator are transferred to another.
• The only Bio-Art articulators, which are interchangeable, are those which are calibrated in
the factory. Thus, for safe and precise interchangeability, casts should be transferred only
between calibrated articulators.
• Before using the articulator and face-bow, the professional should check the instrument for
possible damage, distortion of the incisal pin, face-bow's parallelism, proper centricity of
the incisal pin in relation to the lower frame, etc. Should any abnormality be found, Bio-Art's
Technical assistance or Authorized Representative should be contacted immediately.
• The face-bow should be cleaned with warm water prior to its use. The Bite Fork must be
autoclaved and the Earpieces disinfected with a bactericide or with 70° alcohol.
• Bio-Art recommends only warm water for the general cleaning of the articulator and face-
bow.
• When using “godiva” or any other registration material, special care should be taken to
avoid excessive heating of the material, which might burn the patient's mouth. Bio-Art
urges the user to carefully follow the instructions of the registration material manufacturer.
• Because the articulator is a precision instrument, it should be handled, transported and
stored carefully. Bio-Art provides a plastic case (optional accessory) exclusively designed
to accommodate the articulator and to facilitate its transportation.
8 - TECHNICAL SERVICE
For your safety, the technical service of this product should be made by people/companies
authorized by BIO-ART. Please contact us or the distributors, where the product was
acquired.
Our web site is: www.bioart.com.br
12

9 - GUARANTEE
Bio-Art Equipamentos Odontológicos Ltda., grants 1 year warranty, starting from the
date of the device purchase (invoice). The warranty is carried out exclusively by the
authorized distributor and includes any manufacturing defect, being provided
through the repairing of the product and subjected to the following requirements:
• That the product has been used correctly in accordance with the instructions
described in the user manual;
• The claim is followed by the invoice and registered within the warranty period,
accompanying a report with description of the damage and product serial number;
• The product is handled, transported and stored with care;
• The costs of transport (from and to) is paid by the customer;
Warranty limitations:
• Natural wears and tear of parts;
• Misuse, falls or accidents;
• Inadequate transportation;
• Repair by unauthorized person;
• Use in disagreement with the features and purposes of the device;
• Wear from exposure to adverse conditions (humidity, cold and heat);
• Damage from lack of cleaning or maintenance with inappropriate products.
In case of doubt, contact the manufacturer:
BIO-ART EQUIPAMENTOS ODONTOLÓGICOS LTDA.
Rua Teotônio Vilela, 120 - Jardim Tangará
CEP 13568-000 - São Carlos - SP - Brasil
Tel. [phone] - Fax [phone]
website: www.bioart.com.br - E-mail: [email protected]
CNPJ 58.538.372/0001-56 - I.E. 637.034.447.113
13

10 - PART LIST - ARTICULATOR 4000-S
01 UM 1 FRAM1069 LOWER FRAME 4000-S 02 PC 2 FCAN0755 MAGNETIC FITTING
03 UM 2 FECD0049 CONDYLE ELEMENT 04 UM 4 CORI1170 STABILIZING ELASTIC BAND (O´RING)
05 UM 2 CIMA1118 RAIL MOUNTING PLATE MAGNET
06 UM 4 FPIG0076 MOUNTING PLATE GUIDE PIN 07 UM 2 CPIE1524 AFFIXING BLOCK PIN 08 UM 1 SALH0075 BENNETT ANGLE ADJUSTING DEVICE (RIGHT)
09 UM 2 FPIG0062 FACE BOW´S GUIDE PIN 10 UM 1 FCDL1066 CONDYLAR GUIDE (RIGHT) 11 PC 1 FPOS0759 POSITION INDICATOR OF BENNETT ANGLE ADJUSTING DEVICE (RIGHT)
12 UN 2 SCRE0099 SCREW TO FIX THE BENNETT ANGLE ADJUST. DEVICE
13 UN 1 FBCH0059 CONDYLAR BUSH (RIGHT)
14 UN 1 FFUS0042 MICROMETRIC EXPANDING SPINDLE
15 UN 1 FRLD0061 PULLEY
16 UN 2 SCRE0008 CONDILAR GUIDE WING SCREW
17 UN 2 FFIX0057 CONDYLAR GUIDE FIXER
18 UN 1 SCRE0010 MOUNTING PLATE SCREW (UPPER)
19 UN 1 FBCH0060 CONDYLAR BUSH (LEFT)
20 PC 1 FPOS0758 POSITION INDICATOR OF BENNETT ANGLE ADJUSTING DEVICE (LEFT)
21 UN 1 FCDL1067 CONDYLAR GUIDE (LEFT)
22 UN 1 SALH0074 BENNETT ANGLE ADJUSTING DEVICE (LEFT)
23 UN 1 SCRE0011 INCISAL PIN SCREW
24 UN 1 FRAM0056 UPPER FRAME 4000-S
25 UN 4 SPLA0079 RAIL MOUNTING PLATE
26 UN 1 FPIN0053 INCISAL PIN
27 UN 1 CMES1537 INCISAL TABLE STANDARD (POLYCARBONATE)
28 UN 1 FHST0058 CONDYLE ELEMENT SHAFT
29 UN 1 SCRE0078 INCISAL TABLE SCREW
30 UN 1 SCRE0082 MOUNTING PLATE SCREW (LOWER)
31 UN 2 FPIN0744 STABILIZING ELASTIC BAND PIN
Item Unit Qtd. Code Description
14

Item Qty Code Description
1 1 SCRE0078 INCISAL TABLE SCREW
2 1 FRAM0731 LOWER FRAME A7
3 1 FMES0063 INCISAL TABLE STANDARD (POLYCARBONATE)
4 1 FTAP0761 FINISHING COVER OF RIGHT COLUMN 5 1 FAGU0753 OCCLUSAL PLAN INDICATOR
6 1 FPIN0750 INCISAL PIN WITH HOLE 7 1 FRAM0740 UPPER FRAME A7 PLUS 8 1 SALH0075 BENNETT ANGLE ADJUSTING DEVICE (RIGHT)
9 1 SGUI0073 CONDYLAR GUIDE (RIGHT)
10 2 FPIN0744 STABILIZING SILICONE BAND PIN
11 1 FPOS0759 POSITION INDICATOR OF BENNETT ANGLE ADJUSTING DEVICE (RIGHT)
12 2 SCRE0099 SCREW TO FIX THE BENNETT ANGLE ADJUSTING DEVICE
13 1 CPIN1197 UPPER FRAME SUPPORT PIN
14 2 FTRA0765 LOCK OF UPPER FRAME
15 2 CANE0319 CONDYLAR GUIDE O-RING
16 1 CETQ1113 MODEL IDENTIFICATION LABEL
17 2 FFIX0766 CONDYLAR GUIDE FIXER
18 2 SCRE0008 CONDYLAR GUIDE SCREW
19 1 FTAP0764 PULLEY FINISHING COVER 20 1 FPOS0758 POSITION INDICATOR OF BENNETT ANGLE ADJUSTING DEVICE (LEFT)
21 1 SGUI0072 CONDYLAR GUIDE (LEFT)
22 1 SALH0074 BENNETT ANGLE ADJUSTING DEVICE (LEFT)
23 4 FPIG0076 MOUNTING PLATE GUIDE PIN
24 2 FCAN0755 MAGNETIC FITTING
25 2 CIMA1118 RAIL MOUNTING PLATE MAGNETIC
26 2 SPLA0079 RAIL MOUNTING PLATE
27 1 SCRE0011 INCISAL PIN SCREW
28 2 CPAR1119 CONDYLAR ELEMENT SCREW
29 2 CMOL1100 STABILIZING SILICONE BAND
30 2 FECD0734 CONDYLAR ELEMENT
31 2 FPIG0788 FACE BOW'S GUIDE PIN
32 1 FTAP0760 FINISHING COVER OF LEFT COLUMN 33 1 SCRE0082 MOUNTING PLATE SCREW (LOWER FRAME)
34 1 SCRE0010 MOUNTING PLATE SCREW (UPPER FRAME)
11 - PART LIST - ARTICULATOR A7 PLUS
15

12- PART LIST - ARTICULATOR A7 FIX
Item Qty Code Description
1 1 SCRE0078 INCISAL TABLE SCREW
2 1 FRAM0731 LOWER FRAME A7
3 1 FMES0063 INCISAL TABLE STANDARD (POLYCARBONATE)
4 1 FPIN0750 INCISAL PIN WITH HOLE
5 1 FTAP0761 FINISHING COVER OF RIGHT COLUMN
6 2 FPIN0756 LOCK PIN OF CENTRIC POSITION (ARTICULATOR)
7 2 FPIG0779 FACE BOW'S GUIDE PIN
8 1 SRAM0080 UPPER FRAME
9 1 CPIN1197 UPPER FRAME SUPPORT PIN
10 1 FTAP0777 MAGNET FINISHING COVER (RIGHT)
11 2 CIMA1111 STABILIZER MAGNET
12 1 FTAP0778 MAGNET FINISHING COVER (LEFT)
13 2 CIMA1118 MOUNTING PLATE MAGNET
14 2 SPLA0079 RAIL MOUNTING PLATE
15 1 SCRE0011 INCISAL PIN SCREW
16 2 CPAR1119 CONDYLAR ELEMENT SCREW
17 2 CORI1112 O-RING OF LOCK PIN
18 2 FECD0752 CONDYLAR ELEMENT
19 1 FTAP0760 FINISHING COVER OF LEFT COLUMN
20 2 FCAN0755 MAGNETIC FITTING
21 2 FPIG0076 MOUNTING PLATE GUIDE PIN
22 2 SCRE0082 MOUNTING PLATE SCREW
23 1 FAGU0753 OCCLUSAL PLAN INDICATOR
16

13 - PART LIST - STANDARD FACE-BOW
Item Qt Code Description
1 2 SBBL0001 Wing screw
2 1 FFIX0362 Piece to fix the cross bar (without hole)
3 2 FMOL0025 Elastic washer
4 1 SEXP0006 Horizontal slide bar
5 1 STAR0005 Cross bar
6 1 FPNZ0020 Nose piece support
7 4 SCRE0020 Face-bow wing screw
8 1 FHST0018 Nose piece shaft
9 1 FBLO0016 Nose piece
10 1 FARC0784 Face-bow arm (Right) 11 1 FAUR0033 Ear piece (Right)
12 1 CETQ0018 Model identification label 13 1 FAUR0032 Ear piece (Left) 14 1 CELA0009 Elastic band 15 1 FARC0785 Face-bow arm (Left) 16 1 FPOR0039 Center nut 17 1 SGDE0007 Bite fork 18 1 FBLO0008 Connection Block (internal) 19 2 FTMP0027 Stopping screw 20 1 FBLO0006 Connection block (external) 21 1 CARR0004 Washer for the block 22 1 FBLO0026 Fork´s connection block 23 1 CPIE0005 Affixing block pin 24 1 FFIX0022 Affixing block (with hole)
17