bioBidet BB-800 Technical Document

Installation Manual and
Operating Instructions
BB-800, 900, 1000
This Product should be installed according to this manual.
Please read this manual carefully and install properly.
Please keep this manual for future reference.
Please register Warranty for proper service.
PERSONAL HYGIENE APPLIANCE
ELECTRONIC BIDET TOILET SEAT
PDS Hygiene
Greyfriars, Greyfriars Close, Old Catton,
Norwich, Norfolk NR6 7DX
Telephone: [phone]
Fax: [phone]
E-mail : [email protected]
www.pdshygiene.com
DISTRIBUTOR
www.biobidet.com

Thank you for purchasing The Bio Bidet Electronic Bidet Toilet Seat
This unit was manufactured for household use.
MAINTENANCE
WATER DRAINING
TROUBLE SHOOTING
SPECIFICATIONS
WARRANTY
INFORMATION TO THE USER
OPERATION (BASIC)
OPERATION (DETAILS)
INSTALLATION
SEPARATION OF THE UNIT FROM
THE TOILET BOWL
IMPORTANT SAFEGUARDS /
GENERAL CAUTIONS
CAUTIONS BEFORE INSTALLATION
CARTON CONTENTS / IDENTIFICATION
PREPARATION OPERATION INSTALLATION MAINTENANCE
Contents
4
7
8
9
10
14
17
18
19
20
21
22
23
3
2Installation Manual and Operating Instructions
Bio Bidet
ELECTRONIC BIDET TOILET SEAT
Installation Manual and Operating Instructions
ELECTRONIC BIDET TOILET SEAT

4
IMPORTANT SAFEGUARDS / GENERAL CAUTIONS
1
The following terms are used in this manual to indicate hazards of varying degrees of severity
Indicates potentially hazardous situation which, if not avoided, may result in minor or
moderate injury or in damage to the product or other property.
Indicates potentially hazardous situation which, if not avoided,
could result in death or serious injury.
WARNING
Indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
DANGER
CAUTION
READ ALL INSTRUCTIONS BEFORE INSTALLATION AND USE
DANGER - To reduce the risk of electrocution
WARNING - To reduce the risk of burns, electrocution, fire or injury to persons
PLEASE OBSERVE THE FOLLOWING PRECAUTION BEFORE USING THIS PRODUCT
PREPARATION
Do not open the product to repair or remodel.
Only qualified service personnel should service this product.
Do not use attachments not recommended by the manufacturer.
Do not dismantle
Connect the product to cold water supply pipe
carrying potable water.
Do not connect to an industrial water supply line that
does not carry water of drinking quality as this
will negatively affect hygiene and performance.
Prohibited
About Low Temperature Burns-
A burn occurs when the skin has been exposed to high temperatures. However,
a low temperature burn may occur when the skin has been in contact with an
object at relatively low temperature (about 104 ℉/40℃). Close supervision is
necessary when this product is used by children or people with sensitive skin.
Prohibited
If using any chemical toilet bowl cleaner, be sure to
wipe up any spills that splash onto The Electric Bidet.
Do not use benzene or any acid chemical detergent.
Only neutral detergent permitted.
Prohibited
5
Do not plug in the power cord before connecting
the water supply hose.
Prohibited
This product must be earthed.
An approved residual current device(RCD) must be used.
Earthing
Do not splash water on this product. Please provide
adequate ventilation to avoid damage to electronic
components due to high level of humidity.
It is necessary to provide adequate ventilation with a
fan, open door or open window when bathing.
Do not spray water
Do not touch the power cord with wet hands.
Do not reach for a product that has fallen into water.
Unplug immediately!
Wet hands prohibited
This product must be connected to a standard
voltage power source. Do not connect power
cord if the cord is damaged or broken.
Do not plug the unit into a loose electric outlet.
Observe at all times
Please disconnect the power cord when you clean
this product or detach it from toilet bowl.
Do not supply electrical power to the unit until the
plumbing work has been completed.
Observe at all times
Keep the electrical cord away from heated surfaces to
prevent a fire hazard. Also, keep any flammable materials
away from this product at all times.
Use of fire prohibited
Bio Bidet
ELECTRONIC BIDET TOILET SEAT
Installation Manual and Operating Instructions Installation Manual and Operating Instructions
ELECTRONIC BIDET TOILET SEAT

7
6
PREPARATION
CAUTION
Never operate this product if it is not
working properly, if it has been
dropped or damaged, or dropped into
water. Return the product to a service
centre for examination and repair
Prohibited
Do not obstruct or
put anything into the
dry air outlet. Do not
apply excessive force
to the shower nozzle.
Prohibited
Do not strain or push the connected hose and tube connecter;
it may cause water leakage. Never drop or insert any object
into any opening or hose. Use proper plumbing supplies if any
modification is to be made.
Prohibited
Drain the water from the unit and switch off the power if it is
not going to be used for an extended period of time.
Refer to page 19
Observe at all times
Do not stand or sit
on the seat lid.
It is not designed to
support a user’s
body weight.
Prohibited
Allow the seat
and lid to close
automatically;
do not force the
seat and lid.
Prohibited
Use this product only as
described in the operating
instructions. Never use while
sleeping or drowsy.
Do not use while bathing.
Observe at all times
Be careful so that
this product does not
become stained with
excrement and urine.
Observe at all times
- SAVE THESE INSTRUCTIONS - OPTIONAL ADDITIONAL EARTHING INSTRUCTIONS
Improper earthing can result in a risk of electric shock. Electric wiring must be done
in accordance with all local and national codes.
WARNING : This appliance must be earthed.
Bio Bidet
ELECTRONIC BIDET TOILET SEAT
Installation Manual and Operating Instructions Installation Manual and Operating Instructions
CAUTIONS BEFORE INSTALLATION
2
This product is supplied with a three-pin earthing plug complying with BS 1363 which must be
plugged into a three pin earthed power socket(220-240V AC, 50-60Hz) and protected by a residual current
device(RCD). The rated power consumption is 600-700W.
If this product is used in a bathroom or shower room, the supplied plug must be cut off and
the connection to the power supply must be made via a switched fused spur and RCD.
No other appliance should share the spur with this product.
The work must be carried out by a qualified electrician.
The use of an extension cord is not recommended. If it is necessary to use an extension cord, use
only a three-pin extension cord incorporating a RCD and a socket that will accept the plug on this product.
The marked rating of the extension cord should be equal to or greater than the rating of this unit(10amp)
Consult a qualified electrician if you are unsure whether the unit is properly earthed.
If repair of the cord or replacement of the plug is necessary, this should only be carried out by a
competent person using a plug complying with BS 1363.
If in any doubt about the correct wiring of the plug, an electrician should be consulted.
The manufacturer and distributor cannot be held responsible for damage or injury resulting
from the use of this product on other than specified voltage or without proper earthing.
WIRING REQUIREMENT
ELECTRONIC BIDET TOILET SEAT

9
8
IDENTIFICATION
3
OPERATION (BASIC)
4
MAIN UNIT
1
ACCESSORIES
2
Simple Operation Panel
For
BB-1000
Remote
control
Remote control
Fixed Panel
Battery (2pcs)
1.5V AA
Parts for BB-1000 only
Washer (2 pcs) Cone Packing (2 pcs)
Mounting Bolts (2 pcs)
Installation Base (1 pc)
Nuts (2 pcs)
Installed Bolt Case
(2 pcs)
Water Supply Tube to
Toilet Fresh Water Tank
T-Valve and Washer
Nut to Water Tank
Water Supply Tube to Toilet Seat Deodorizer Filter Cartridge/
Carbon Deodorant
(BB-900 / 1000 Models)
User
Operating
Manual
Backflow Prevention
CHECK VALVE
Adaptor Valve
•When you sit on the seat, please sit down on the central position
in order to activate the sensor.
•After an extended wash, allow about three minutes for water to reheat.
Adjust the
oscillation
function and
nozzle position
(5 levels)
Power Saving
mode button.
Simple Operation Pane l
Stop
Posterior Wash
Feminine Wash
BB-800, 900 Control Panel BB-1000 Remote Control
Adjust the water
pressure and
warm air dryer
temperature.
Adjust the
water and seat
temperature
(3 levels).
Adjust the
water and seat
temperature
(3 levels)
Adjust the
oscillation
function and
nozzle position
(5 levels)
Adjust the water pressure and
warm air dryer temperature.
Power Saving
mode button.
OPERATION
Operation
Guide
Bio Bidet
ELECTRONIC BIDET TOILET SEAT
Installation Manual and Operating Instructions Installation Manual and Operating Instructions
Feminine Wash Nozzle
Posterior Wash Nozzle
Turbo Wash Nozzle
ELECTRONIC BIDET TOILET SEAT
Feminine Wash Nozzle
Posterior Wash Nozzle
Digital Occupied Sensor
Drain / Quick Release
Operation LED Window
Heated Seat
Lid
Caution Label
Deodorizer
(Only BB-1000)
Dryer Vent
Control Panel for
BB-800, 900
Turbo Wash Nozzle
BB-800, 900
BB-1000

11
WARM WATER TEMPERATURE
AND SEAT TEMPERATURE ADJUSTMENT
10
OPERATION (DETAILS)
5
PREPARATION
1
SIT ON THE SEAT
• When you sit on the seat, the digital sensor on the seat is activated and the ORANGE LED lamp
on the main unit indicating
“Occupied sensor” will light up.
•Simultaneously the Deodorizer fan will start working. (BB-900 / 1000 Models)
•See page 11 for details about changing the seat or water temperature.
•Check for any water leaks.
•Plug the unit into the proper power source and the LED power light will start flashing.
•Wait until the LED power light stops flashing and becomes solid red.
•The water tank will be filled after pressing a “Wash”( , or , ) button.
•When the water tank is filling the buzzer “Beeps”continuously.
After the water tank is full the buzzer will end with “One Solid Beep”.
OPERATION
2
CLEANSING
•CLEANSING 1. (Posterior Wash)
1- Press “ Posterior ” (, ). The nozzle comes out and
sprays warm water to posterior.
2- Additional functions during Posterior Wash are available. See Oscillation,
pg.12 and Massage, pg. 13 for details.
STOP
•Press this button to stop all operation.
•CLEANSING 2. (Feminine Wash)
1- Press “Feminine”(
,
). The nozzle comes out and
sprays warm water to feminine area.
2- Additional functions during Feminine Wash are available. See Oscillation,
pg.12 and Massage, pg. 13 for details.
• CLEANSING 3. (Turbo Wash)
1- Press “Turbo Wash” (, ) . The nozzle spray is more focused
to produce the effect a strong wash, to help stimulate bowel movement.
2- Press “ / button”to adjust the water pressure.
OPERATION
CLEANSING cont.
Room temperature approx. 93.2℉ (34 ℃ ) 98.6℉ (37 ℃ ) 104℉ (40 ℃ )
SEAT TEMPERATURE
WATER TEMPERATURE
Room temperature approx. 93.2℉ (34
℃ ) 98.6℉ (37 ℃ ) 105.8℉ (41 ℃ )
•CLEANSING 3. (Turbo Wash)
1- Press “Turbo Wash”, The water nozzle comes out and
sprays a concentrated stream of water to the posterior.
2- If necessary, adjust “Position”of water stream with the ( / )buttons.
3- Press
“ / button” to adjust the water pressure as desired.
4- Press the “STOP”( )button when you feel your abdomen is full or wait until
the “Turbo Wash”function stops. (approximately 1 minute.)
5- You will shortly feel the urge to push the water out of your colon, push the water and feces
out as completely as you can.
6- Relax for a few minutes and be sure you feel your colon is empty and then use
the “Posterior Wash”and “Air Dry”function to finish.
WARM AIR DRYER
1- Press “Dry”( , ), warm dry air is gently directed to washed area for about 3 minutes.
2- You may adjust the warm air temperature by pressing High( ) and Low( ) buttons.
※This product memorizes the air temperature of prior use.
WATER PRESSURE ADJUSTMENT
•After sitting down on the seat, the LED lamp( ) for water
pressure on the Power Control will light at third or middle level( )
•Press high( ) , or low( ) to adjust the pressure of the water spray to
your desired comfort level
•The temperature of water and seat are adjustable to the desired level by pressing
the “WATER”( , )and “SEAT”( , ) button.
CAUTION
DO NOT ALLOW CHILDREN TO USE THE TURBO WASH FUNCTION!
SUPERVISION IS STRONGLY RECOMMENDED FOR THE ELDERLY OR OTHER PERSONS
THAT MAY HAVE LIMITATIONS IN BODY MOVEMENT, ILLNESS OR DISABILITIES!
Observe at all times
Bio Bidet
ELECTRONIC BIDET TOILET SEAT
Installation Manual and Operating Instructions Installation Manual and Operating Instructions
ELECTRONIC BIDET TOILET SEAT

12 13
•Nozzle position is adjustable to the desired position by pressing “Front”( ) or
“Rear”( ) button from 1 to 5 positions.
When selecting a wash cycle the nozzle will extend to its last used position.
OPERATION (DETAILS)
5
NOZZLE POSITION ADJUSTMENT
•The deodorizer fan is activated when the seat is occupied.
When finished, the fan will stop after 1 minute.
•Air current for the deodorizer has 4 adjustable levels. While pressing the “STOP”( ) button,
press the “WATER”( , ) button to the desired air current level. See diagram:
DEODORIZER (BB-900, 1000 Models)
1 Level
OFF
Deodorizer
(Air Current)
Occupied →
Low Speed
After using →
Low Speed
Deodorizer
(Air Current)
Occupied →
Low Speed
After using →
High Speed
Deodorizer
(Air Current)
Occupied →
High Speed
After using →
High Speed
2 Level 3 Level 4 Level
(Level1~4)
( , )
+
•When using Posterior or Feminine Washing functions, pressing the “MOVE”( , )
button will provide a short-motion, front to back oscillating spray for a much wider cleansing
effect. Note: This function will not work during the “Turbo Wash”function.
• You may change the position of the Oscillating spray by pressing the
“Front”( ) or “Rear”( ) button.
• Push the “ MOVE ”( , ) button again and the oscillation motion will stop automatically.
Auto-Setting of Oscillation Feature
•You can set this function to automatically oscillate whenever the seat is occupied and the Posterior or
Feminine washes are in operation.
•Without sitting on the seat, press
•The “MOVE”( , ) button for 3 seconds or until you hear a single Chime.
•Sit on the seat and proceed with Posterior or Feminine Wash.
Note :In the automatic setting, you may still adjust the position of the Oscillating spray by pressing the
“Front”( ) or “Rear”( ) buttons.
Canceling the Automatic Oscillation function
•Without sitting on the seat, press
•The “MOVE”( , ) button for 3 seconds or until you hear a double Chime.
OSCILLATION ( Nozzle Movement Function)
•When using any of the wash programs pressing the “MASSAGE”( , )
button will provide a pulsating spray.
•You may change the pressure of the spray by pressing the “High”( ) button or
“Low”( ) button.
•Push the “MASSAGE”( , ) button again and the pulsating action will stop automatically.
Auto-Setting of Massage Feature
•You can set this function to automatically pulsate whenever the seat is occupied and
any of the wash programs is in operation.
•Without sitting on the seat, press
•The “MASSAGE”( , ) button for 3 seconds or until you hear a single Chime.
•Sit on the seat and proceed with the wash program.
Note
:In the automatic setting, you may still adjust the pressure of the pulsating spray by
pressing the “high”( ) or “low”( ) buttons.
Canceling the Automatic Oscillation function
•Without sitting on the seat, press
•The “MASSAGE”( , ) button for 3 seconds or until you hear a double Chime.
MASSAGE (Rhythm Wash)
ECONOMY (Energy Save Mode)
- The ENERGY SAVER is not on when the LED light is off.
- Press button once to choose“ECONOMY 1”
- Press button again to choose“ECONOMY 2”
- Press button third time to turn “ECONOMY”off
* ECONOMY 1 : the water temperature will be kept at 90℉(32℃)
* ECONOMY 2 (SMART MODE) : this will lower the water temperature to 90℉(32℃) when it is not
being used, and raise the water temperature back to normal level during the time of use.
It takes about 4 days for the unit to
“learn”
, and
“remember”
, the usage pattern of the user(s)
NOZZLE CLEANING (Automatically)
• This product has an automatic nozzle self-cleaning function that cleans the nozzle before and after each use.
CHIME SOUND ON/OFF SET
•While sitting on the seat, press “MOVE”( , ) button for 3 seconds and you can hear
the chime sound change to ON or OFF. (Remote model doesn’t have off function, BB-1000)
NOZZLE CLEANING (Manual)
•Nozzle can be cleaned manually by pressing “Posterior Wash”( / ) button for 3 seconds
while the seat is not occupied ; the nozzle will come out without spraying water.
After cleaning the nozzle, Press “Stop”( , ) button to return nozzle to stand-by mode.
( , : in Simple Operation panel -Remote Model)
OPERATION
Bio Bidet
ELECTRONIC BIDET TOILET SEAT
Installation Manual and Operating Instructions Installation Manual and Operating Instructions
ELECTRONIC BIDET TOILET SEAT

15
14
INSTALLATION
INSTALLATION
6
CAUTION BEFORE INSTALLATION
•Do not connect to electricity before water connection.
•
If you need an electric power system or extension, please consult a qualified electrician.
STEPS
Existing Flexible Tube
(The water supply hose)
Existing Flexible Tube
(The water supply hose)
DOUBLE CHECK VALVE MUST
COMPLY WITH THE UK WATER
REGULATION
Thread from tank
(TEFLON tape is strongly recommended around threads to help prevent leakage) (TEFLON tape is strongly recommended around threads to help prevent leakage)
CHECK
VALVE
ADAPTOR
1Removing the existing seat and lid.
•Release the nuts on both sides of existing toilet
seat to remove the seat and lid.
2
Remove existing supply pipe from the cistern tank and connect the tee to the cistern tank.
Connect the double check valve supplied to the tee and the 1/2”male-male adaptor to the
check-valve. Connect existing supply pipe to the tee.
An approved double-check valve must be installed on the inlet connection to this device.
※Check for any water leaks. ※Check for any water leaks.
3
Shut off the water supply to the
existing toilet tank by closing the
angle stop valve. Drain the toilet
tank completely by flushing toilet.
Remove the water supply hose to
toilet tank.
Intallation Base
1. Put the 2 Bolts into the 2 Installed Bolt Cases
2. Place this Bolt assembly into the Installation
Base as shown.
3. Guide Arrows on the Installation Base should
face up and towards the Toilet Tank.
4. Place the Installation Base and guide the Bolts
into the 2 holes on the toilet bowl.
4
1. Slide the seat onto the installation Base centering
the unit with the guide arrows on the Base.
2. You will hear a click once the seat is securely
mounted to the Installation Base.
3. The seat will feel a little loose on the toilet bowl.
Adjust the fit from front to back and side to side for balance.
4. Tighten the nuts on both bolts securely.
6
1. Connect the flexible tube from male-male
Adaptor to the seat.
2. Open the water valve.
3. Check for leaks.
4. If there are no leaks and the surrounding
area is clean and dry, connect the power
cord to a ground protected power outlet.
7
1. Fit the cone packing and plastic washers onto
the bolts from below the toilet bowl as shown.
2. Loosely tighten nuts by hand.
5
Installation Base Assembly. Bolt and Nut Assembly.
Bio Bidet Shower Toilet Seat Assembly. Water Supply Tube Assembly.
Cone Packing
Washer
Nut
Bio Bidet
ELECTRONIC BIDET TOILET SEAT
Installation Manual and Operating Instructions Installation Manual and Operating Instructions
Bolt Case
Bolt
ELECTRONIC BIDET TOILET SEAT

17
16
INSTALLATION
INSTALLATION
6
SEPARATION OF UNIT FROM THE TOILET BOWL
7
How to change the deodorant catalyst
Place 1.5V(AA) batteries properly
and shut the cover
Deodorant case
Deodorant
Cover
Adhesive Tape
Installation of Remote Control on wall or convenient surface. (BB-1000)
•Check the deodorant package.
•Follow the photos below to change the deodorant.
1
2Insert the new deodorant case into the unit.
1- Mount Fixed Panel to wall location.
Peel the cover from the adhesive tape on the
Remote Control Fixed Panel and use the
adhesive tape in order to stick the
Remote Control Fixed Panel on wall.
2- Then slide Remote Control on to
Remote Control Fixed Panel.
Deodorizer Installation.
Insert the deodorant cartrige into the unit.
(BB-900 / 1000 Models)
9
10
Switch off power supply.
Shut off the Water Supply Valve.
Push the button on the right side of the unit to
completely drain the water from water tank.
Separate the unit from toilet as following photos.
Do not turn unit upside down.
•When you pull the unit while pushing the drain button, the unit will separate from the installation base.
1
2
3
4
Bio Bidet
ELECTRONIC BIDET TOILET SEAT
Installation Manual and Operating Instructions Installation Manual and Operating Instructions
ELECTRONIC BIDET TOILET SEAT

19
18
MAINTENANCE
MAINTENANCE
8
WATER DRAINING
9
MAINTENANCE FOR WINTER SEASON
•When the “Posterior Wash ( / )”button is pressed
for 3 seconds without occupying the seat, the nozzle can be
cleaned with a soft toothbrush.
•After cleaning the nozzle, push the “Stop ( , )”
button once again, and the nozzle retracts itself.
( : in Simple Operation panel -Remote Model)
1) Close the water shut off valve.
2) Flush the toilet to empty the water reservoir.
3) Unscrew the water filter nut.
4) Clean the strainer with a small brush or water.
5) Re-screw the water filter nut.
6) Open the water shut off valve.
This product will not operate
properly if the strainer is clogged.
Please clean the strainer regularly.
BB-800, 900
( : in Simple Operation panel -Remote Model)
CLEANING THE NOZZLE DRAINING THE WARM WATER TANK IN THE UNIT
•When you clean this product, do not use “thinner
” , “benzene ” or
toilet bowl cleaner. It may cause damage to the surface of unit.
•Use a wet cloth when you clean this product.
•Do not spray water directly on to this product.
•When you clean this product, switch off power supply.
CLEANING THE BODY OF UNIT
CLEANING THE STRAINER
If you do not intend to use this product for 14 days or longer,
drain the water from the product warm water tank.
1) Disconnect the power plug.
2) Close the water shut off valve.
3) Press the drain lever until the water is
completely drained from the unit’s water tank.
4) To re-supply water after draining,
open the water shut off valve.
Do not drink the drained water.
Do not insert finger into the drain hole.
Before draining, switch off power and wait 30 minutes until the unit has cooled down.
Check the power is ON or OFF.
1
Keep the water temperature on “Middle or High Level”to prevent water from freezing.
2
If you do not intend to use the unit for 14 days or longer, switch the power off
and drain the water.
3
Bio Bidet
ELECTRONIC BIDET TOILET SEAT
Installation Manual and Operating Instructions Installation Manual and Operating Instructions
BB-1000
ELECTRONIC BIDET TOILET SEAT

21
20
MAINTENANCE
TROUBLE SHOOTING
10
SPECIFICATIONS
11
Trouble Cause Remedy
1.The water tank is not filled.
2.The shut off valve is closed.
3. Freezing inside the main unit
or the water supply pipe.
1.Power is switched off.
2.The seat is not occupied.
3.The battery of remote
controller is exhausted.
(Only BB-1000 model)
1.Faulty connection
2.Faulty unit
1.The water pressure level is set to
“LOW”.
2.The strainer is clogged.
1.The water temperature is set to
“LOW”.
2.Continuous operation has
depleted the supply of warm
water.
1.The seat & dryer temperature is
set to “LOW”.
1.Wait about one minute.
Press the desired washing
button once again.
2.Turn on the shut off valve.
3.Heat the room (for about two
hours). Operating the unit while
parts are frozen will cause a
malfunction.
1.Switch power on.
Check the power supply system
in your house.
2.Occupy the seat (The unit has
an occupied sensor).
3.Replace the battery.
1.Set the water pressure to
“HIGH”.
2.Clean the strainer.
1.Set the water temperature to
“HIGH”.
2.Wait about three minutes.
1.Set the seat & dryer
temperature to “HIGH”.
The washing water
does not spray
The unit is not
operating
Water is leaking
The washing water
pressure is weak
The washing water
is not warm
The seat and dryer
is not warm
Feminine Wash
Wash
Device
Heated Seat
Warm
Air Dryer
Device
Posterior Wash
Water Pressure
Adjustable
Warm Water
Temperature
Heater
Safety Devices
Temperature
Heater
Safety Device
Adjustable Dry Temperature
(Room Temp~45℃)
Deodorizer
Turbo& Enema Function
Remote control
Inlet water temperature
3℃~ 35℃ ( 37.4℉ ~ 95℉ )
3℃~ 40℃ ( 37.4℉ ~ 104℉ )
Ambient Temperature
Dimensions
Weight (kg)
Heater
(250W)
Safety Device
(Themal fuse, bimetal)
Power Rating
Power cord
Type
Water inlet type
Water inlet pressure
Specification
Direct Inlet flow type
0.4 ~ 7.5 kgf/㎠( 5.69 psi ~ 106.7psi )
(1.2m (4 feet): AMERICA) / (1.8m:Australia or Europe)
Max. 1.2ℓ/min ( Max. 0.32 GPM )
Max. 1.2ℓ/min ( Max. 0.32 GPM )
5 Levels
Room Temp - 40
℃ ( Room Temp. 104 ℉ )
600 W
Thermal fuse, Thermal switch, Float switch
Room Temp ~ 41
℃ ( Room Temp. ~ 105.8 ℉ )
55 W
Thermal fuse
5.3kg 5.4kg 5.2kg
BB-800 BB-900 BB-1000
○
○
-
-
○
○
-
○
○
○
○
○
W : 495mm (19.4 inch)
L : 525mm (20.6 inch)
H : 185mm (7.28 inch)
W : 475mm (18.7 inch)
L : 525mm (20.6 inch)
H : 185mm (7.28 inch)
W : 495mm (19.4 inch)
L : 493mm (19.4 inch)
H : 185mm (7.28 inch)
W : 475mm (18.7 inch)
L : 493mm (19.4 inch)
H : 185mm (7.28 inch)
Australia or Europe: 220 - 240V~, 50/60Hz , 600 - 700W
America or Canada: 120Vac, 60Hz, 660W
Bio Bidet
ELECTRONIC BIDET TOILET SEAT
Installation Manual and Operating Instructions Installation Manual and Operating Instructions
Elongated(Control) Elongated (Remote)Round (Control) Round (Remote)
1.Fix connections.
2.If water is leaking from the main unit,
call the service center or the place you
purchased.
ELECTRONIC BIDET TOILET SEAT

23
22
MAINTENANCE
WARRANTY
12
INFORMATION TO THE USER
13
Serial Number #
Date of Purchase
Purchaser
Dealer(Company)
To ensure your warranty protection you must complete and return this card along with
a copy of your receipt to PDS Hygiene within 30 days after Date of Purchase.
Model
company
Address
City
Phone
Address
Country
E-mail
Dealer Code
MAIL TO :
PDS Hygiene
GREYFRIARS
GREYFRIARS CLOSE
OLD CATTON
NORWICH
NORFOLK NR6 7DX
Telephone: [phone]
Fax: [phone]
E-mail : [email protected]
Web : www.pdshygiene.com
WARRANTY REGISTRATION
Bio Bidet
ELECTRONIC BIDET TOILET SEAT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more
of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the manufacturer could void the user's authority to
operate the equipment.
Note : The manufacturer is not responsible for any Radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user's authority to operate the equipment.
WARNING
Installation Manual and Operating Instructions Installation Manual and Operating Instructions
PDS Hygiene One Year Limited Warranty
1. All Our products are warranted to be free from manufacturing defects under normal use and
service for a period of one (1) year from date of purchase. This warranty is extended only to
the ORIGINAL PURCHASER. This warranty does not affect your statutory rights as a consumer.
2. Our obligations under this warranty are limited to repair or replacement, at our option, of
products or parts found to be defective, provided that such products were properly installed and
used in accordance with instructions. We reserve the right to make such inspections as may
be necessary in order to determine the cause of the defect. We will not charge for labour, parts
or carriage in connection with warranty repairs or replacements. We are not responsible for the
cost of removal or reinstallation of the products.
3. This warranty does not apply to the following items:
a. Damage or loss sustained in a natural calamity such as fire, earthquake, flood, electrical storm etc.
b. Damage or loss resulting from any unreasonable use, misuse, abuse, negligence or
improper maintenance of the product.
c. Damage or loss resulting from removal, improper repair or modification of the product.
d. Damage or loss resulting from sediments or foreign matter contained in a water system.
e. Damage or loss resulting from improper installation or from installation of a unit in a
harsh and/or hazardous environment.
4. This written warranty is the only warranty made by us. Repair or replacement as provided
under this warranty shall be the exclusive remedy available to the purchaser. We shall not be
responsible for loss of the product or for other incidental, special or consequential damages or
expenses incurred by the purchaser, or for labour or other costs due to installation or removal, or
costs of repairs by others, or for any other expense not specifically stated above. Except to the
extent prohibited by applicable law, any implied warranties, including that of merchantability or
fitness for use, are expressly limited to the duration of this warranty.
Note : We will not be responsible or liable for any failure of or damage to this plumbing product or
product component caused by either chloramines in the treatment of public water supply or in-tank bowl
cleaners containing chlorine (calcium hypochlorite). The use of high concentration of chlorine or
chlorine related products could seriously damage the fittings. This damage can cause leakage and
serious property damage.
To obtain repair service under this warranty, you must first contact us in writing (see Contact Details below)
to obtain a Return Merchandise Authorisation (RMA) and return instructions.
Contact Details
Post : PDS Hygiene, Greyfriars, Greyfriars Close, Old Catton, Norwich, Norfolk NR6 7DX
Tel : [phone]
Fax : [phone]
E-mail : [email protected]
ELECTRONIC BIDET TOILET SEAT